Quick Start Guide

02BLP1M

Speco Technologies

1 Warning and Caution ⚠️

If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. Any unauthorized changes or modifications could void the warranty.
Do not allow water or liquid intrusion into the camera.
All installation and operation here should conform to local electrical safety codes. Make sure the device is firmly installed on the wall or ceiling.
Do not use camera beyond specified voltage range.
Do not drop the camera or subject it to physical shock.
Avoid touching the camera lens.
If cleaning is necessary, please use cleaning cloth to wipe it gently.
Do not aim the camera at the sun or extremely bright light sources.
Do not place the camera in extremely hot or cold environments and dusty and damp locations. Do not expose it to highly electromagnetic radiation.
Do not block any ventilations.

2 Package ?

Camera
Quick start guide
CD
Drill template
Screwdriver
Junction box
4 tapping screws ?
1 machine screw ?
Plastic plug ×4

3 Overview ?️

Diagram shows a camera with cables extending from its rear, labeled with numbers 1 through 10 corresponding to connector types.

1: Ethernet Connector
2: MIC-Audio Input
3: HP-Audio Output
4: Alarm Output/Input
5: Power Connector *
6: Micro SD Card Slot ?
7: Zoom +* ?
8: Zoom -* ?
9: CVBS output (unavailable)
10: Reset ?

* 1 It is recommended to install the security cap for outdoor installation.

* 2 If the PoE switch is used to power the camera, DC12V power supply is not required.

Connecting Network Cable ?

Diagram illustrating the connection of a network cable:

Loosen the nut from the main element.
Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector.
Connect the cable to the hermetic connector. Then tighten the nut and the main cover.

The process involves three steps: loosening a connector nut, routing the cable through components, and connecting to a hermetic connector.

4 Installation ?

SD Card Installation ?

Open the camera cover, insert a micro SD card, and then re-install the cover. Ensure the cover is installed evenly.

Diagram shows a camera with its cover removed, indicating where a micro SD card is inserted. A close-up shows the SD card slot.

Camera Installation with a Junction Box ?️

Important: Before starting, ensure the wall or ceiling is strong enough to support three times the weight of the camera and junction box.

Open the mounting base and the upper cover of the junction box.
Install the mounting base of the junction box onto the wall using the provided screws ?.

Diagram shows the components of a junction box: a mounting base and an upper cover, with arrows indicating they are being opened.

Camera Installation with Junction Box (cont.)

Fix the mounting base of the camera to the upper cover of the junction box.
Route the cables through the cable hole and connect the camera. Then install the camera onto the mounting base of the junction box.
Three-axis Adjustment: Before adjustment, preview the camera's image on a monitor. Loosen the fixed screws to adjust the camera to the optimum angle.

Diagram shows the camera being mounted to the junction box's upper cover, then routed through a cable hole, and finally attached to the mounting base. A subsequent diagram shows the camera mounted and being adjusted with fixed screws for pan (360°), tilt (90°), and rotate (360°).

Configuration requirements of camera and surrounding area ⚙️

Note: Installation requirements are based on optimum conditions; license capture rate may vary with speed, lighting, position, and license plate designs.

The monitoring image should cover the lane, entry/exit vehicles, and their license plates must be visible.
Avoid objects blocking the camera (e.g., pillars, obstacles, doors).
Avoid scenes with many trees or moving objects (humans, non-motor vehicles).

Overhead Monitoring

Installation height (H): 15~20 ft.
Distance D (camera to captured area): 50~82 ft. (Typically 3-4 times the installation height).
Distance of captured area (L): 50~65 ft.

Diagram illustrates an overhead monitoring setup. A camera is mounted at height H (15-20ft) overlooking a road segment of length L (50-65ft) at a distance D (50-82ft) from the camera. A vehicle speed limit of <40MPH is indicated.

Depression angle: 10° to 15°.
Pan angle (side of road installation): 0° to 20°.
Pan angle (directly above middle of road): -10° to 10°.

Entrance & Exit Monitoring

Installation height (H): 4.2~5 ft.
Distance D (camera to captured area): 8.2~10 ft.
Distance of captured area (L): 5~6.5 ft.

Diagram illustrates an entrance/exit monitoring setup. A camera is mounted at height H (4.2-5ft) overlooking a lane segment of length L (5-6.5ft) at a distance D (8.2-10ft) from the camera.

Depression angle: 0° to 5°.
Pan angle: 5° to 20°.

The tilt angle of the license plate

After installation, log into the web client to check the license plate tilt in the video. The tilt angle should range from -5° to 5°.

Diagram shows three representations of license plates. The first two are within acceptable tilt angles (indicated by checkmarks ✔️), while the third is at an unacceptable angle (indicated by a cross ❌).

If the captured license plate does not meet requirements, adjust the pan angle of the camera.

5 Web Operation and Login ?

IP Scanner can search for the device on the local network.

Operation

Ensure the camera and PC are connected to the same local network. The camera defaults to DHCP.
Install and run IP Scanner from the CD.

Screenshot of the 'SecureGuard IP Scanner' software interface showing a list of network devices, including the 'O2BLP1M' model with its IP and MAC addresses. Below this is a screenshot of a login page with fields for 'Username' and 'Password'.

Default username is 'admin' and password is '1234'. After logging in, follow instructions to install necessary plugins.

	Speco Technologies 08VT2 Quick Start Guide This guide provides essential information for the Speco Technologies 08VT2 network camera, covering safety precautions, package contents, device overview, installation steps, and web-based operation for setup and configuration.
	Speco Technologies 04T7N Network Camera Quick Start Guide This guide provides instructions for setting up and operating the Speco Technologies 04T7N network camera, covering installation, network connection, and web interface access.
	Speco Technologies 08LMST1 Network Camera Quick Start Guide A quick start guide for the Speco Technologies 08LMST1 network camera, detailing installation steps, overview of features, and web operation and login procedures. Includes important safety warnings and package contents.
	Speco Technologies 04FT2W Quick Start Guide This quick start guide provides essential information for installing and operating the Speco Technologies 04FT2W network camera, including setup, network connection, and web interface access.
	Speco Technologies 04VT1M Quick Start Guide: Installation and Operation A comprehensive quick start guide for the Speco Technologies 04VT1M IP Turret Camera, detailing installation steps, package contents, and initial web operation.
	Speco Technologies 04BDD1M Network Camera Quick Start Guide Get started quickly with the Speco Technologies 04BDD1M network camera. This guide provides essential information on installation, connection, and basic operation for your surveillance system.
	Speco Technologies 05D2 Quick Start Guide A concise guide for installing and operating the Speco Technologies 05D2 network camera, including setup, connections, and web interface access.
	Speco Technologies 08D7M IP Dome Camera Quick Start Guide A quick start guide for the Speco Technologies 08D7M IP Dome Camera, detailing its features, package contents, installation steps, and web operation. Includes important safety warnings and maintenance tips.