Ingenuity InLighten™ Soothing Swing - Dakota™

Important! Read Carefully and Keep for Future Reference

⚠️ WARNING

Fall and Strangulation Hazards: Infants have suffered head injuries falling from seats and have strangled in straps.

• ALWAYS use the restraint system. Adjust to fit snugly.
• STOP using product when infant attempts to climb out (approximately 9 months).
• DO NOT use this product once your child can sit up unaided or weighs more than 9 kg/20 lbs. DO NOT use this product if your child weighs less than 3kg/6 lbs.
• Stay near and watch baby during use. This product is not safe for sleep or unsupervised use. If baby falls asleep, remove baby as soon as possible and place baby on a firm, flat sleep surface such as a crib or bassinet. Never let the child sleep in this product.
• DO NOT move or lift this product with the baby inside it. Never lift product using a toy bar as a handle.
• ALWAYS place product on floor. NEVER use this product on an elevated surface (e.g. a table).
• NEVER attach any additional strings or straps to product or toy bar.

Suffocation Hazard: Young infants have limited head and neck control. If the seat is too upright, infant's head can drop forward and compress the airway.

• ALWAYS keep swing seat fully reclined until infant is at least 4 months old AND can hold up head without help.

Babies have suffocated when seats tipped over on soft surfaces.

• NEVER use on a bed, sofa, cushion, or other soft surface.

Prevent Serious Injury or Death

• NEVER leave the child unattended.
• To avoid injury, ensure that children are kept away when unfolding and folding this product.
• Do not let children play with this product.
• When using the USB cord, only use the one supplied with this swing.
• Check the USB cord and wall adaptor regularly for damage. Do not use if any damage has occurred.
• Use USB cord only with a 5 Volt/1 Amp (5 Watts) USB A wall adaptor.
• The product shall only be used with a transformer for toys.
• The transformer is not a toy.
• This product is only to be connected to equipment bearing either of the following symbols: [Π symbol], [III symbol].
• Do not use extension cords.
• NEVER use as an infant carrier for automobile or airline travel.

CAUTION

This product contains small parts. Adult assembly required.

IMPORTANT

• The provided USB cord is 183cm in length.
• Please read all instructions before assembly and use of the product.
• Care should be taken in unpacking and assembly.
• Examine product frequently for damaged, missing, or loose parts.
• DO NOT use if any parts are missing, damaged, or broken.
• Contact Kids2 for replacement parts and instructions if needed. Never substitute parts.
• This product does not replace a cot or a crib. Should the child fall asleep, then it should be placed in a suitable cot or crib.

Battery Information

The remote control requires a CR2032 (3V) battery (included). The vibration Unit requires (1) size C/LR14 (1.5V) alkaline batteries (not included).

⚠️ WARNING:

INGESTION HAZARD: This product contains a button cell or coin battery.

• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN.
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Call a local poison control center for treatment information.

CAUTION:

Follow the battery guidelines in this section. Otherwise, battery life may be shortened or the batteries may leak or rupture. To prevent battery leaks, which can burn skin and eyes:

• Examine product and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if compartment is not secure.
• Dispose of used button batteries immediately and safely. Batteries can still be dangerous.
• Always keep batteries away from children.
• Never mix old and new batteries, or batteries of different brands or types.
• Always replace the entire set of batteries at one time.
• Do not mix alkaline, standard, or rechargeable batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Install the batteries so that the polarity of each one matches the markings in the battery compartment.
• Do not short-circuit the batteries.
• Do not store batteries in areas that have extreme temperatures (such as attics, garages, or automobiles).
• Do not force discharge, recharge, disassemble, heat above 60°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Remove exhausted batteries from the battery compartment.
• Never attempt to recharge a battery unless it is specifically marked "rechargeable."
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Dispose of used batteries immediately.
• Please use the correct disposal method for batteries.
• Remove batteries before putting the product into storage for a prolonged period of time.
• Weak batteries cause erratic product operation, including distorted sound, dimming or failed lights, and slow or non-working motorized parts. Because each electrical component requires a different operating voltage, replace the batteries when any function fails to operate.
• Do not dispose of product or batteries in fire, batteries may explode or leak.
• This symbol indicates that the product is not to be disposed of in household waste as batteries contain substances that can be damaging to the environment and health. Contact local authority for recycling & collection information.

Care and Cleaning

• Seat pad: Remove from frame. Fasten buckles on seat restraint and seat pad. Fasten all hook-and-loop patches to the corresponding patch. Machine wash with cold water, gentle cycle. No bleach. Tumble dry, using low heat.
• Bolster: Machine wash with cold water, gentle cycle. No bleach. Air dry flat.
• Toys: Wipe clean with a damp cloth and mild soap. Air dry. Do not immerse in water.
• Frame: Wipe the metal frame with a soft, clean cloth and mild soap.
• Storage: When putting swing away for storage, always store in a dry location, away from any heat sources, and out of the sun.

Parts List

Assembly Instructions

Follow these steps to assemble your Ingenuity InLighten Soothing Swing:

Step 1: Attach Leg Tubes

Connect the left leg tube (2) and right leg tube (4) to the main swing frame (1). Ensure they click securely into place. The front feet (3, 5) are attached to the bottom of these tubes.

Step 2: Attach Front Feet

Attach the left front foot (3) and right front foot (5) to the bottom of the leg tubes (2, 4).

Step 3: Connect Cross Brace

Attach the cross brace assembly (7) between the leg tubes (2, 4) using screws (A) and nuts (B) as shown in the diagram.

Step 4: Attach Swing Arm Assembly

Connect the swing arm assembly (6) to the top of the main frame (1). Secure it using screws (A) and nuts (B).

Step 5: Attach Recline Mechanisms

Attach the left recline (9) and right recline (8) components to the swing arm assembly (6).

Step 6: Attach Footrest Tube

Connect the footrest tube (10) to the swing arm assembly (6).

Step 7: Install Vibe Unit

Open the battery compartment on the Vibe Unit (12) using a screwdriver. Insert 1.5V C/LR14 batteries (not included) following the polarity markings. Close the compartment securely.

Step 8: Mount Vibe Unit

Attach the Vibe Unit (12) to the underside of the swing seat frame.

Step 9: Prepare Seat Pad

Align the seat pad (15) with the seat frame. Attach the back rest tube (11) to the seat pad.

Step 10: Secure Seat Pad

Attach the seat pad (15) to the swing seat frame. Ensure it is securely fastened.

Step 11: Attach Harness

Thread the harness straps through the seat pad and frame. Ensure the straps are correctly positioned and secured.

Step 12: Install Seat

Place the assembled seat onto the main swing frame.

Step 13: Secure Seat

Fasten the seat securely to the frame, ensuring all locking mechanisms are engaged.

Step 14: Attach Mobile

Attach the mobile arm (13) to the top of the swing frame. Hang the mobile toys (18, 19) onto the mobile arm.

Step 15: Connect USB Cable

Connect the USB cable (14) to the Vibe Unit (12) and to a compatible USB power source (5V/1A adaptor required, not included).

Step 16: Add Head Rest and Bolster

Place the head rest (16) and bolster (17) onto the seat pad for added comfort and support.

Step 17: Install Seat Restraint

Position the seat restraint (17) onto the seat pad and secure it.

Step 18: Attach Toys

Attach the elephant toy (19) and the circle toy (18) to the mobile arm as shown.

Using the Seat Restraint

Follow the diagrams to correctly thread and secure the seat restraint straps through the seat pad and frame. Ensure all buckles are fastened and adjusted snugly for the infant.

Using the Recline Function

To adjust the recline position, locate the recline adjustment lever on the side of the seat. Move the lever to select the desired recline angle.

Rotation of the Seat

To rotate the seat, press and hold the rotation lock button while turning the seat to the desired position. Release the button to lock the seat in place.

Storage and Travel

To fold the swing for storage or travel, press the release buttons on the legs and fold the frame inwards. Ensure the swing is stable before storing.

IR Remote Operation

The remote control requires one CR2032 (3V) battery. Open the battery compartment on the remote using a screwdriver. Insert the battery, ensuring correct polarity. Close the compartment securely.

Using the Swing Control Module

The control module allows you to manage various functions of the swing.

Power

Touch the Power switch to turn the Swing Control Module on or off.

Speed Selector

The Speed Selector provides 5 speed settings and an OFF setting. Touch the button to cycle through the settings until the LED bar graph displays the desired speed. The LEDs will flash for five seconds during adjustment. The swing stops when the timer expires.

Timer

Use the Timer Select function to automatically turn off the swing. Touch the button to cycle through 30, 60, or 90-minute settings. If no setting is selected (all LEDs OFF), it defaults to 30 minutes. To resume swinging after auto-shutoff, press the Timer Select or Speed Selector button.

Nature Sounds/Music

Touch the Nature Sounds/Music button to play music and nature sounds. Touch as needed to select desired songs or sounds. Auto-shutoff occurs after approximately 20 minutes.

Volume Control

Touch the Volume Control switch to adjust the volume for music and nature sounds, or to turn them off.

Mobile Illumination

Press the Mobile Illumination button to start the mobile and its lights. Press again to cycle through random light/play patterns.

Using the Vibration Unit

To use the vibration function, push the button on the Vibe Unit to turn it on or off.

FCC Statement / CAN ICES-3 (B) / NMB-3(B)

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Déclaration FCC / CAN ICES-3 (B) / NMB-3(B)

Cet appareil est conforme à l'article 15 de la réglementation FCC. Son utilisation est sujette aux deux conditions suivantes : 1 ce dispositif ne peut causer d'interférences nuisibles, et 2 ce dispositif doit accepter toute interférence reçue, y compris les interférences pouvant causer un fonctionnement indésirable.

ATTENTION : Toute modification apportée à cet appareil, sans consentement explicite des responsables conformité, est susceptible d'annuler le droit d'usage de cet appareil.

REMARQUE : Cet article a été testé et déclaré conforme aux exigences requises pour les appareils numériques de classe B, conformément à l'article 15 de la réglementation FCC. Ces exigences visent à assurer une protection raisonnable contre les interférences nuisibles dans une installation chez des particuliers. Cet appareil génère, utilise et peut émettre de l'énergie radioélectrique, et s'il n'est pas installé et utilisé conformément aux instructions, il est susceptible de perturber les communications radio.

Nous ne pouvons garantir la non-interférence pour une installation donnée. Lorsque vous constatez que le matériel perturbe effectivement la réception radio ou télévision, vous pouvez vérifier ces interférences en éteignant et rallumant l'appareil. Dans ce cas, essayez une ou plusieurs des mesures suivantes :

• Réorientez ou déplacez l'antenne de réception.
• Éloignez l'appareil et le récepteur.
• Raccordez le matériel à une prise hors-circuit connexion de ce récepteur.
• Adressez-vous au fournisseur ou à un technicien expert en radio et télévision.