RYNOSKIN Standard Width Front Bumper Installation Instructions
Part No. RSFB-JK0001
Fits:
- 2007-2018 Jeep Wrangler JK
- 2018-2024 Jeep Wrangler JL (Excludes Rubicon/plug-in hybrid models/2021-2024 V8 engine)
- 2020-2024 Jeep Gladiator (Excludes Mojave trim)
Installation Overview
⏱️Installation Time: 90-180 minutes (time may vary by individual).
✔️Cutting Not Required
✔️Drilling Not Required
Tools Required
- Screwdriver
- Ratchet Socket Set
- Torque Wrench
- Allen Wrench (Provided)
- Trim Panel Removal Tool
Torque Specifications
DO NOT OVER TORQUE. PLEASE FOLLOW THE TIGHTEN OPERATING LOAD STANDARD BELOW:
- 6mm Bolts & Nuts: 7 to 8.5 Foot Pounds
- 8mm Bolts & Nuts: 18 to 20 Foot Pounds
- 10mm Bolts & Nuts: 35 to 40 Foot Pounds
- 12mm Bolts & Nuts: 60 to 70 Foot Pounds
Cleaning and Care
TO PROTECT YOUR INVESTMENT, DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES THAT COULD DAMAGE THE FINISH. MILD SOAP MAY BE USED TO CLEAN THE PRODUCT.
Parts List
| Description | Qty | Image | Remark |
|---|---|---|---|
| Bumper | 1 | [Image of the main front bumper assembly] | |
| 3/4" D-Rings | 2 | [Image of a D-ring shackle] | |
| Plastic Retainers | 4 | [Image of a plastic retainer clip] | |
| Fog Light Brackets | 2 | [Image of a fog light mounting bracket] | |
| M12*35 Combo Bolts | 4 | [Image of an M12x35mm combo bolt with washer face] | |
| M12x35mm Bolts | 4 | [Image of an M12x35mm bolt] | |
| M12 Nuts | 4 | [Image of an M12 nut] | |
| M12 Flat Washers | 8 | [Image of an M12 flat washer] | |
| M12 Lock Washers | 8 | [Image of an M12 lock washer] | |
| M4x15mm Button Head Bolts | 12 | [Image of an M4x15mm button head bolt] | Use the provided S=2.5 Allen wrench to tighten |
| M4 Flat Washers | 20 | [Image of an M4 flat washer] | |
| M4 Lock Washers | 12 | [Image of an M4 lock washer] | |
| M4 Nuts | 8 | [Image of an M4 nut] | |
| S=2.5 Allen Wrench | 1 | [Image of a 2.5mm Allen wrench] | Use for 4mm hardware |
Note: Images in the original document are illustrative representations of the parts.
Installation Procedure
-
Step 1: Preparation
Remove contents from the box and verify all parts are present. Read all instructions carefully. Factory installed or aftermarket front bumpers must be removed before proceeding.
-
Step 2: Remove Factory Splash Shield
Remove the six (6) plastic push pins securing the factory splash shield to the vehicle. Four (4) are located across the front edge, and two (2) are on the rear edge. [Illustration showing removal of plastic push pins from the factory splash shield].
-
Step 3: Disconnect Fog Lights
From under the vehicle, remove the factory fog light connectors and free the fog light wiring loom from the bumper. [Illustration showing disconnection of factory fog light connectors and wiring loom].
-
Step 4: Remove Factory Bumper Nuts
From under the vehicle, access and remove the eight (8) 18mm nuts securing the factory bumper to the vehicle. [Illustration showing removal of nuts securing the factory bumper].
-
Step 5: Remove Top Cover Push Pins
Remove the two (2) push pins holding the top cover onto the vehicle. [Illustration showing removal of push pins holding the top cover].
-
Step 6: Remove Fog Light Screws
Remove the eight (8) 7mm screws securing the fog lights to the factory front bumper. [Illustration showing removal of screws securing fog lights].
-
Step 7: Install Fog Light Brackets
Install the fog light bracket using six (6) M4 Bolts, ten (10) M4 Flat Washers, six (6) M4 Lock Washers, and four (4) M4 Nuts. Repeat this process for both fog lights. [Illustration showing installation of fog light bracket with M4 hardware].
-
Step 8: Install M12 Combo Bolts
Slide the two (2) M12 combo Bolts into place through the open square in the Bumper, and secure them with two (2) Plastic Retainers. Repeat this process for both bracket parts. [Illustration showing installation of M12 combo bolts and plastic retainers].
-
Step 9: Mount Bumper
Slide the bumper into place. Using the supplied M12 hardware, secure each side of the bumper to the vehicle using four (4) M12 Nuts, four (4) M12 Bolts, eight (8) M12 Lock Washers, and eight (8) M12 Flat Washers. Torque to 40 ft-lbs. [Illustration showing bumper mounting and securing with M12 hardware].
-
Step 10: Final Connections
Install the D-Ring brackets to the bumper. Plug the factory fog light harness into the fog lights. Installation is complete. [Illustration showing installation of D-Ring brackets and fog light harness connection].
RYNOSKIN
