Remote Control Button Map
The remote control features a circular arrangement of buttons at the top, including TV, ANT, SNORE, HEAD, FOOT, FLAT, TILT, LUMBAR, MODE, and TIMER/ALL OFF. There are also numbered buttons from 1 to 18, each corresponding to a specific function.
System Configuration Diagram
This diagram illustrates the interconnected components of the smart home bed system. It shows two types of remote controls (HJH109 and HJH159), control boxes (HJC27 and HJC4S), single motor drivers for head, foot, and lumbar sections (HJA35, HJA66), massage rollers (HJM2), and LED light strips (HJT21A). The diagram depicts the wiring and connections between these components, including power supply and data lines. A table lists the specific part numbers, quantities, and descriptions for each component. Another table provides dimensions for certain parts.
Component List
| Serial No. | Material Name | Material Code | Quantity | Remarks |
|---|---|---|---|---|
| 1 | HJC27 Control Box | 80C270012 | 1 | Bluetooth |
| 2 | HJA35 Single Motor Driver | 144980A350616 | 1 | Head |
| 3 | HJA35 Single Motor Driver | 144980A350615 | 1 | Foot |
| 4 | HJA66 Single Motor Driver | 1449804660305 | 1 | Head |
| 5 | HJA66 Single Motor Driver | 1449804660306 | 1 | Foot |
| 6 | HJM2 Massage Roller | 800M20022 | 2 | Borrowed |
| 7 | HJT21A LED Strip | 800T21A0003 | 1 | Borrowed |
| 8 | HJC4S Control Box | 80C4S0002 | 1 | Borrowed |
| 9 | HJTU5 Charging Base | 80TU50001 | 2 | Borrowed |
| 10 | HJH109 Remote Control | 8H1090019 | 1 | YS-H109-016 |
| 11 | HJH159 Remote Control | 8H1590005 | 1 | Sync Cable |
Dimensions:
| Item | Dimension 1 | Dimension 2 |
|---|---|---|
| ZG | 41mm | 30mm |
| TV | 94mm | 0 |
| Anti | 25mm | 0 |
Change Record: Customer requirement - 1449-22062301 - Idealbed New Handset H158/H159
Remote Control Function Description
| Button Label | Function |
|---|---|
| 1 | Under-bed light on/off (5 minutes off) |
| 2 | Short press and release to run to TV position (with initial value). Multiplexing function: FLAT+TV, the backlight flashes, the buzzer sounds, and the current motor position is recorded to the TV position. (Power-off clear). |
| 3 | Short press and release to run to SNORE position (with initial value). Multiplexing function: FLAT+SNORE, the backlight flashes, the buzzer sounds, and the current motor position is recorded to the SNORE position. (Power-off clear). |
| 4 | Short press and release to run to ZG position (with initial value). Multiplexing function: FLAT+ZG, the backlight flashes, the buzzer sounds, and the current motor position is recorded to the ZG position. (Power-off clear). |
| 5 | Back up, release to stop |
| 6 | Feet rise, release to stop |
| 7 | Back down, release to stop |
| 8 | Feet down, release to stop |
| 9 | One-key reset, all motors reset to the end, power-on reset. |
| 10 | External drag two rise, release stop (TILT) |
| 11 | External tow two descend, release stop (TILT) |
| 12 | Pull it up and release it to stop (LUMBAR) |
| 13 | Pull down and release to stop (LUMBAR) |
| 14 | The head massager is enhanced, the massager can be turned on (automatically turn off after 30 minutes) (1→2→3→4→5→6→7→off cycle switching) |
| 15 | The foot massager is enhanced, the massager can be turned on (automatically turn off after 30 minutes) (1→2→3→4→5→6→7→off cycle switching) |
| 16 | Light up the flashlight |
| 17 | Adjust the massage motor mode. After the massager has been turned on, pressing this button cycles through modes: 'PULSE', 'WAVE', 'CONSTANT', and back to 'PULSE'. |
| 18 | Massager off. The working time of the massager is set at 10min, 20min and 30min respectively, and the timing time is displayed by the indicator light. Reserved function: The motor runs to the M1 position with one key (no initial value) (not clear when power off). |
Pairing and Learning Function
Pairing Method: [Remote control back up + foot up (buttons 5, 6) + control box pairing key]. The buzzer sounds, indicating successful pairing. The control box's code key has a reset function. The control box, when powered on, resets, and this process cannot be interrupted by any key.
Remote Control Mutual Learning Function: (A: to learn the remote control, B: to learn the remote control)
1. B learns A: Long press B's back down + foot down (buttons 7, 8) for 5 seconds. The flashlight turns on. Within 10 seconds, press back up + foot up (buttons 5, 6). B's flashlight flashes, indicating learning success.
2. To cancel learning function: Long press B's back up + foot down (buttons 5, 8) for 5 seconds. The flashlight turns on, indicating cancellation is successful.
Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
