H300-310 Assembly Instructions and Safety Guide
Important Safety Notice
Always use proper tools. Follow assembly steps in order; do not skip any steps. Check all packing materials carefully for small parts that may have come loose inside the carton during shipment. If parts are missing, contact the retailer from which you purchased the product to obtain any missing parts. DO NOT USE SUBSTITUTE PARTS. Periodically check to ensure that all connectors (bolts, screws, etc.) are tight. Keep the instructions for future reference. Handle glass or mirrors with extreme care, as severe injury may result if they break. Never handle large pieces of glass or mirrors by yourself. When assembling products that have electric cords (lamps, light, etc.), always ensure the electrical cord is unplugged before assembly and be careful not to twist the electrical cord during assembly. When assembling shelves or entertainment centers, do not stand on lower shelves to assemble upper shelves; use a step ladder. Do not stand on tables, including but not limited to, end tables, coffee tables, and dinner tables, as tables are not designed to support the weight of a person. Where assembly instructions state that assembly requires two or more people, do not attempt by yourself as there is a risk of injury. Ashley Furniture Industries, LLC disclaims any liability for damages or injuries which may occur due to failure to properly follow assembly instructions, properly assemble the product, or properly use the product. Note: Your unit may look different in appearance from the one shown in the illustrations on this instruction sheet.
Parts List
- Ax2: Two (2) Frame Side Panels
- Bx2: Two (2) Frame Side Panels
- Cx1: One (1) Crossbar
- Dx2: Two (2) Shelf Panels
- Ex1: One (1) Back Panel
- Fx11: Eleven (11) Bolts (1/4" x 28mm)
- Gx4: Four (4) Bolts (1/4" x 18mm)
- Hx1: One (1) Allen Wrench (4mm)
- Jx8: Eight (8) Screws (#4 x 13mm)
- Kx6: Six (6) Screws (#8 x 27mm)
- Lx2: Two (2) Levelers (Not Included)
Assembly Steps
Step 1
Attach two (2) Frame Side Panels (A) to the Crossbar (C). Use four (4) bolts (F) and four (4) washers (G). Do not tighten any bolts until all bolts have been started.
Diagram Description: Shows two frame pieces (A) being connected to a crossbar (C) with bolts (F) and washers (G).
Step 2
Attach the other two (2) Frame Side Panels (B) to the Crossbar (C). Use four (4) bolts (F) and four (4) washers (G).
Diagram Description: Shows the other set of frame pieces (B) being attached to the crossbar (C) using bolts (F) and washers (G).
Step 3
Attach the Shelf Panels (D) to the frame assembly. Use six (6) screws (K) to attach the shelf panels (D) to the frame.
Diagram Description: Shows two shelf panels (D) being screwed into the frame structure using screws (K).
Step 4
Attach the Back Panel (E) to the frame. Use eight (8) screws (J) to attach the back panel (E) to the frame.
Diagram Description: Shows the back panel (E) being attached to the assembled frame using screws (J).
Step 5
Attach Levelers (L) to the bottom of the unit's legs. If the unit is placed on an unlevel surface, place a leveler underneath one foot until the unit is level. Break off any protruding segments.
Diagram Description: Shows levelers (L) being attached to the bottom of the unit's legs. Close-ups illustrate placement and adjustment.
Step 6
The unit is now fully assembled.
Diagram Description: Shows the completed furniture piece.
Additional Information
Contact and Support
For replacement parts or assistance, please contact:
- Email: RTAParts@ashleyfurniture.com
- Website: www.ashleyfurniture.parts
- Phone: 1-844-966-0809
General Assembly Notes
- The unit should be assembled by two or more people.
- Do not tighten any bolts until all bolts have been started.
- Periodically check to ensure all connectors are tight.
- Keep these instructions for future reference.