Winix C545(AU) Air Purifier

Product Overview

Thank you for purchasing a Winix air purifier. This product is designed for household use and features a 4-stage air purification system with PlasmaWave® technology and Wi-Fi connectivity.

Package Contents

• (1) Pre-Filter
• Unit
• (8) Activated Carbon Filters
• (2) True HEPA Filters
• User Manual
• Wi-Fi Setup Guide

Where to Use

Placement Guidelines:

• Allow 30-45cm of space between the unit and other electronics to prevent electromagnetic interference.
• Place indoors away from direct sunlight, which may cause malfunction or failure.
• Only place on hard, flat surfaces to avoid abnormal noise and vibrations.
• Ensure at least 30-45cm clearance from walls for optimal air flow.

4-Stage Air Purification

The Winix C545(AU) uses a four-stage process to purify the air:

1. Pre-Filter: Captures larger airborne particles like dust and pet hair.
2. Activated Carbon Filter: Reduces odors, VOCs, and smoke.
3. True HEPA Filter: Captures 99.97% of airborne particles as small as 0.3 microns, including fine dust, pollen, mold spores, and bacteria.
4. PlasmaWave® Technology: Creates hydroxyls to help neutralize airborne viruses, bacteria, and gases without producing harmful ozone.

Control Panel

The control panel features the following indicators and buttons:

• 01. Auto Mode Indicator: LED light indicates when Auto Mode is active.
• 02. Air Quality Indicator: Color-coded LED shows air quality: Red (poor), Amber (fair), Blue (good).
• 03. Fan Speed Indicator: Displays the current fan speed setting.
• 04. Sleep Mode Indicator: LED light indicates when Sleep Mode is on.
• 05. Filter Replacement Indicator: Illuminates when it's time to replace the filter.
• 06. Filter Reset Button: Press and hold for 5 seconds after filter replacement to reset the indicator.
• 07. Smart Sensor: Detects odorous gases and adjusts fan speed automatically in Auto Mode.
• 08. Power Button: Turns the unit on or off.
• 09-1. Fan Speed/Auto/Sleep Buttons: Cycle through fan speeds (Auto, Low, Medium, High, Turbo, Sleep).
• 09-2. PlasmaWave® Button: Toggles PlasmaWave® technology on or off. A slight chirping sound may occur, which is normal.
• 10. PlasmaWave® Indicator: Shows if PlasmaWave® is enabled or disabled.
• 11. Wi-Fi Button: Press and hold for 3 seconds to activate pairing mode.
• 12. Wi-Fi Indicator: Shows Wi-Fi status (flashing during pairing, solid white when connected).
• 13. Light Sensor: Detects ambient light to activate Sleep Mode automatically in Auto Mode.

For Wi-Fi setup, refer to the provided Winix Smart Wi-Fi Setup Guide.

Initial Operation and Filter Installation

1. Grasp the upper edge of the front panel and gently pull forward to remove it.
2. Remove the Pre-Filter, then the bag containing the other filters.
3. Remove filters from their protective plastic bags.
4. Install the filters in the correct order: Pre-Filter (front), Activated Carbon Filter (middle), True HEPA Filter (back). Ensure they fit securely.
5. Close the front panel.
6. Insert the power cord into an electrical outlet.

Note: The smart sensor takes approximately 4 minutes to detect air quality for initial operation.

Maintenance and Filter Replacement

Filter Lifespan and Service:

Note: Filter replacement intervals may vary depending on the environment.

Replacing Filters and Resetting Life:

1. After replacing the True HEPA Filter, re-install the Pre-Filter and close the front panel.
2. With the unit powered on, press and hold the Filter Reset Button for at least 5 seconds until a beep is heard. The Filter Replacement Indicator will turn off, indicating the True HEPA Filter life has been reset.

Cleaning and Care

Cleaning the Filters:

• Pre-Filter: Use a vacuum cleaner or soft brush. If excessively soiled, rinse in room temperature water. Do not use detergent or soap. Allow to dry completely (24+ hours) before re-installing.
• Activated Carbon & True HEPA Filters: These filters cannot be washed and should be replaced as per the maintenance schedule.

Cleaning the Exterior & Interior:

• Wipe the exterior with a soft damp cloth using room temperature water, then dry with a clean cloth.
• Open the front panel and clean the interior with a vacuum cleaner. Clean every 1-2 months for optimal performance.

Notice: Always unplug the unit before cleaning. Do not use hot water over 40°C, volatile fluids, flammable sprays, liquid detergents, benzene, alcohol, or paint thinner. Do not allow children to clean or maintain the unit unsupervised.

Specifications

Exterior design and specifications are subject to change without prior notice.

For replacement filters, visit ausclimate.com.au/pages/filter-club.

Safety and Cautions

General Safety:

• Read and follow all safety instructions before operating.
• Ensure filters are installed before running the unit.
• Do not insert foreign objects into vents.
• Do not touch interior parts with wet hands.
• Ensure intake and outlet vents are not blocked to prevent overheating and failure.
• Do not use the unit as a step stool or place heavy objects on it.

WARNING: Follow instructions to reduce risk of electric shock, short circuit, fire, or injury.

• If the supply cord is damaged, it must be replaced by the manufacturer, service agent, or qualified persons.
• This appliance can be used by children aged 8 and above under supervision. Persons with reduced capabilities can use it if supervised and instructed safely.
• Children should be supervised to ensure they do not play with the appliance.
• Cleaning and user maintenance should not be done by children without supervision.
• Always unplug the unit before cleaning or maintenance.
• Avoid damaging the power cord by bending, pulling, twisting, bundling, pinching, or placing heavy objects on it.
• Do not install in motor vehicles or transport vehicles.
• Do not place in areas with excessive noxious gases, flammable materials, or excessive humidity.
• Do not place closer than 30 cm from walls during operation to prevent condensation.
• Do not use around industrial oil mist, metallic dust, or where the unit may become wet.
• Do not place below electrical outlets or facing into wind/drafts.
• Do not pull the power cord when unplugging; grasp the plug itself.
• Do not tie or knot the power cord during operation.
• If the unit is submerged in water, unplug and contact customer service.
• Do not unplug or move the unit while in operation.
• Do not plug additional appliances into the same outlet.
• Do not handle the power plug with wet hands.
• Unplug the unit when not in use for extended periods.
• Do not place around heating elements.
• Do not operate without a filter.
• Do not wash and reuse the True HEPA Filter.
• Hold by the handle on the back for transport; do not hold by the front panel.
• Do not stick small objects into air outlet vents or the fan.
• Do not use near flammable gases, cigarettes, incense, or spark-creating items.
• Use AC 220-240 V only.
• Periodically remove dust from the power plug to reduce shock risk from humidity.
• Do not use detergent to clean the unit; do not use benzene or paint thinner. Do not spray insecticides on the unit.
• Do not operate when using indoor smoke-generating insecticides.
• Do not use where it is humid or may become wet, such as a bathroom.
• Do not use the unit on its side.
• Keep away from products that generate oily residue, such as deep fryers.

Frequently Asked Questions

Problem: It does not turn on at all.

Check / Actions: Is the plug securely attached to the outlet? Ensure the outlet has power. Is there a power outage? Check other electrical equipment.

Problem: It doesn't work in Auto Mode.

Check / Actions: Has Auto Mode been selected? Press the Mode button until Auto Mode is selected.

Problem: It vibrates and makes a lot of noise.

Check / Actions: Is it running on a slanted or uneven surface? Move the unit to a hard, flat, even area of the floor.

Problem: The power plug and outlet feel hot.

Check / Actions: Is the plug securely plugged in? Ensure the plug is properly inserted into the outlet.

Problem: There is a strange smell.

Check / Actions: Is it being used in a place with a lot of smoke, dust, or odors? Clean air intakes and the Pre-Filter. Clean or change the filters.

Problem: The fan strength is weak. The unit is not purifying the air.

Check / Actions: Is the Check Filter indicator light on? Change the filters as required.

Problem: The display panel is dim.

Check / Actions: Is the Light Sensor blocked by debris? When Auto Mode is on, Sleep Mode is automatically activated when the Light Sensor detects darkness.

Product Warranty

Product Name: Air Purifier

Model Name: C545(AU)

Warranty Period: Two (2) Years

Please complete the warranty information below after purchase:

Purchase Date: _________________________

Place of Purchase: _________________________

Place of Purchase Tel: _________________________

Address: _________________________________________________________________

Customer Name: _________________________

Tel: _________________________

Address: _________________________________________________________________

Additional Notes

The product uses the "WFM60-SFP201" wireless module. The RCM mark was added to this user manual due to label size constraints on the module itself.

This product is manufactured for use only in Australia and is suitable for 220-240 V only.

For support, visit www.cdbgroup.com (Australia: PO Box 574 South Morang Victoria 3752; New Zealand: PO Box 100707 North Shore Mail Centre Auckland 0745).