PowerA Battle Dragon Wireless Controller User Manual

Contents

• Controller
• USB adaptor
• 5 ft./1.5 m USB-C to USB-A Cable
• Two analog caps
• User Manual

Charging Controller

For best results, fully charge the controller prior to first use.

1. Using a USB-C Cable, connect the USB-C port at the top of the controller to a powered USB source.
2. While charging, the battery indicator LED will flash AMBER.
3. When fully charged, the battery indicator LED will be solid GREEN.
4. The battery indicator will flash RED when the battery is low.

Wireless Mode: 2.4G

1. Insert the wireless USB dongle into an open PC USB port.
2. Set the mode switch on the back of the controller to "RF".
3. If the controller is off, press the [Home Button] to turn it on (LED will illuminate WHITE).
4. Press and hold the [Sync Button] on top of the controller for 3 seconds to enter pairing mode (LED will flash WHITE rapidly).
5. Enter the Settings menu on your device and choose the PC Wireless controller. The LED will turn solid WHITE when connected.

Note: A previously paired device will automatically pair to the controller when powered on.

Wireless Mode: Bluetooth

1. Set the mode switch on the back of the controller to "BT".
2. If the controller is off, press the [Home Button] to turn it on (LED will illuminate BLUE).
3. Press and hold the [Sync Button] on top of the controller for 3 seconds to enter pairing mode (LED will flash BLUE rapidly).
4. Enter the Bluetooth settings on your device.
5. Select the PC Wireless Controller. The LED will turn solid BLUE when connected.

Note: A previously paired device will automatically pair to the controller when powered on.

Wired Mode: USB

1. Set the mode switch on the back of the controller to "USB".
2. Using the included USB-C Cable, connect the USB-C port at the top of the controller to an available USB port on the PC.
3. If the controller is off, press the [Home Button] to turn it on (LED will illuminate GREEN).

Note: A previously paired device will automatically pair to the controller when powered on.

Mode XInput to DirectInput

(Applicable for 2.4 RF/USB Wired Modes Only)

1. Press and hold the [SELECT] and [START] buttons simultaneously for 3 seconds.
2. The [LED Indicator] will flash 3 times to indicate the mode has been changed.
3. To change modes again, press and hold the [SELECT] and [START] buttons again for 3 seconds until the [LED Indicator] flashes 3 times.

Powering Off

Hold the [Home Button] for 5 seconds to turn the controller off and save battery capacity.

Battery Status Indication

• Low Battery: RED LED
• Battery Charging: AMBER LED
• Battery Charged: GREEN LED

Assigning the Advanced Gaming Buttons

Advanced Gaming Buttons (AGR1, AGR2, AGL1, AGL2) can be programmed to perform actions of other buttons.

1. Press and hold the [Program Button] on the back of the controller for 3 seconds.
2. The [LED Indicator] will flash, signaling the controller is in assign mode.
3. Press one of the following buttons to re-assign: A, B, X, Y, LB, RB, LT, RT, Left Stick Press, Right Stick Press, or D-pad. The [LED Indicator] will flash rapidly.
4. Then, press the Advanced Gaming Button (AGR1, AGR2, AGL1, or AGL2) that you wish to assign. The [LED Indicator] connection indicator will stop flashing, signaling the Advanced Gaming Button has been set.
5. Repeat steps 3 and 4 for the remaining Advanced Gaming Buttons.

Note: Advanced Gaming Button assignments will remain in memory even after the controller is disconnected.

Resetting the Advanced Gaming Buttons

1. Hold the [Program Button] down for 2 seconds. The [LED Connection Indicator] will slowly flash, signaling the controller is in assign mode.
2. Press the previously assigned button for 5 seconds, and the function will be cleared.

Turbo Setting

1. Press and hold one of the A, B, X, Y buttons that you wish to set to Turbo.
2. While holding down the desired button, press the [Turbo Button].
3. The [LED Indicator] will flash 3 times to show you Turbo has been set.
4. Press the [Turbo Button] again to turn Turbo off.

Trigger Lock Adjustment

This feature allows adjustment of the trigger sensitivity. A diagram shows a small switch or slider located on the back of the trigger mechanism, which can be moved to adjust the trigger lock.

Analog Caps (Optional Accessory)

Enhance the controller's grip and comfort by attaching the included analog caps to the analog sticks for improved gameplay. The caps are designed to fit over the existing analog sticks.

Troubleshooting

Problem: My controller will not power on.

Solution: Confirm the controller is fully charged. Plug it in to recharge as needed.

Problem: I don't see my PC controller listed in my device's settings.

Solution: Re-try the steps for "Wireless Mode: Bluetooth" pairing.

Problem: My wireless controller is not pairing.

Solution: Confirm the battery is charged by plugging in the USB-C cable. Re-try the pairing process for "Wireless Mode: RF" or "Wireless Mode: Bluetooth". If pairing issues persist, use a pointed object like a paper clip to press the [Factory Reset Hole] on the controller to reset it to factory settings.

For the latest FAQs and support, visit www.powera.com/support.

Motion Warning

Playing video games may cause muscle, joint, skin, or eye discomfort. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation, or eyestrain:

• Avoid excessive play. Take a 10- to 15-minute break every hour, even if you don't think you need it. Parents should monitor their children for appropriate play.
• If your hands, wrists, arms, or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning, or stiffness, stop and rest for several hours before playing again.
• If you continue to have any of the above symptoms or other discomfort during or after play, stop playing and see a doctor.

Battery Warnings

• Do not attempt to repair, disassemble, or modify the battery yourself. Damage to the battery can cause overheating, fire, or injury.
• Dispose of the controller according to your local regulations, as it contains a built-in battery. Contact your local municipality if unsure.
• Do not use or leave the controller in high-temperature environments (e.g., direct sunlight, inside a hot car). High temperatures can cause the battery to overheat or ignite, and may also degrade battery performance and lifespan.
• Avoid using the controller in environments with excessive static electricity. Excessive static can damage the battery's internal safety features, increasing the risk of overheating or fire.
• If battery fluid gets into your eyes, do not rub them. Immediately rinse thoroughly with clean running water and seek medical attention.
• If the battery emits an unusual odor, becomes hot, or shows other abnormalities during use, charging, or storage, immediately remove it from the charging device. Place it in a sealed, fire-resistant container (like a metal box) or in a safe location away from people and flammable materials.
• Do not heat, incinerate, or place the controller or battery near fire.

Two-Year Limited Warranty

For warranty details or support with your authentic PowerA accessories, please visit www.powera.com/support.

Note: Proof of purchase (receipt or invoice) is required for warranty service.

Manufactured For & Legal Information

Manufactured for: ACCO Brands USA LLC, 4 Corporate Drive, Lake Zurich, IL 60047. Visit ACCOBRANDS.COM | POWERA.COM. MADE IN CHINA.

© 2024 ACCO Brands. All Rights Reserved. PowerA and the PowerA Logo are trademarks of ACCO Brands. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ACCO Brands is under license. Other trademarks and trade names are those of their respective owners. USB-C® is a registered trademark of USB Implementers Forum.