MOGA XP5-A PLUS BLUETOOTH CONTROLLER

Setup and Operation

For optimal results, fully charge the controller and power bank before first use.

Charging Controller + Power Bank

Use the included 6.6 ft. (2 m) USB Cable. Connect the Micro-USB end to the lower port at the top of the controller and the Standard USB end to any powered USB source.

During charging, four LEDs will indicate the charging level (25%, 50%, 75%, 100%).

Charge Level Indicator

Check the battery charge level by pressing the [Battery Status Button] located on the front lower left of the controller. The LEDs will show the current charge level (25-100%) even when the controller is off.

Wireless Mode

Move the Wireless/Wired switch on the front center of the controller to [BT Icon] to enable Bluetooth wireless mode.

• If the controller is off, press the [MENU Button] to turn it on (the LED will illuminate).
• Press and hold the [Bluetooth Sync Button] on the top of the controller for 2 seconds to enter pairing mode (the LED will flash rapidly).
• On your device, navigate to Bluetooth settings and select the MOGA controller. The pairing LED will turn solid when connected.

Note: Previously paired devices will automatically connect when the controller is powered on.

Powering Off

Hold the [MENU Button] for 5 seconds to turn off the controller and conserve battery.

Wired Mode

Move the Wireless/Wired switch on the front center of the controller to [USB Icon] to enable wired mode.

• Connect the Micro-USB end of the 11.8" (30 cm) or 6.5ft (2 m) cable to the lower port at the top of the controller, and connect the other end to your gaming device.
• Your gaming device's input ports (Standard USB, Micro-USB, USB-C) will determine the appropriate cable length.
• This MOGA controller supports DirectInput by default and also XInput mode. If the initial wired connection fails, switch modes by pressing Start + Select simultaneously for three seconds. Three LED flashes confirm the mode change.

Gaming Clip

A detachable gaming clip is included for mobile gaming. USB cables can be used with the clip attached for charging or wired mode.

1. Slide the MOGA Controller into the gaming clip by tipping the top edge in first.
2. Push the controller's bottom edge down into the clip until it locks into the notch on the front edge.
3. To insert your phone, push the top edge of the phone against the top of the phone grip to expand it.
4. Push the bottom of the phone down flat into place as you reach the top limit of the phone grip.
5. Adjust the phone horizontally to center it over the controller and set the viewing angle.
6. Open the kickstand on the clip when setting the controller down between sessions to prevent tipping.
7. Remove the clip by pulling the front edge forward to release it from the notch.

Integrated Power Bank

The controller features a built-in power bank to charge your phone during gameplay or when the controller is off.

• Connect the Standard USB end of the 11.8" (30 cm) cable to the upper port on the controller and the other end to your mobile device.
• During gameplay, move the Power Bank switch (located below the right thumbstick) to the right (ON) to start charging. To prioritize controller usage time over phone charging, move the switch to the left (OFF).
• To charge a mobile device when the controller is not in use, simply connect the cable between the controller and device (the Power Bank switch must be ON).
• Your mobile device will show the charge status. If charging doesn't begin, the power bank battery may be too low; recharge the controller.
• The available charge for your phone depends on the controller's remaining battery capacity.

Assigning Advanced Gaming Buttons

1. Press the Orange Program Button on the bottom of the controller for 2 seconds. The LED Connection Indicator will flash, indicating assign mode.

2. Press one of the following buttons (A/B/X/Y/LB/RB/LT/RT/Left Stick Press/Right Stick Press/D-pad) to re-assign. Then press the Advanced Gaming Button (AGR or AGL) you wish to assign. The LED will stop flashing.

3. Repeat for the remaining Advanced Gaming Button.

Note: Advanced Gaming Button assignments are saved even after disconnection.

Resetting Advanced Gaming Buttons

1. Hold the Program Button for 2 seconds. The LED Connection Indicator will flash slowly.

2. Press and hold the assigned button for 5 seconds to clear its function.

Frequently Asked Questions (FAQs)

For the latest FAQs, visit PowerA.com/Support.

Problem: My controller will not power on?

Solution: Confirm the controller is fully charged by pressing the [Battery Status Button]. Plug in to recharge if needed.

Problem: MOGA controller not listed in mobile device Bluetooth settings?

Solution: Press and hold the [Bluetooth Sync Button] on the back of the controller for 2 seconds to enter pairing mode (LED flashes rapidly).

Problem: The integrated power bank is not functioning?

Solution: Ensure the controller has more than 25% charge and the Power Bank button is switched ON.

Safety Information and Warnings

Battery Warning

• Do not attempt to repair the Li-ion battery yourself, as this may cause overheating, fire, or injury.
• The Li-ion battery should be serviced or recycled by PowerA or an authorized provider and disposed of separately from household waste, following local environmental laws and guidelines.
• Avoid using or leaving the device in high-temperature environments (e.g., direct sunlight, hot vehicles), as this can lead to overheating, fire, and reduced battery performance or lifespan.
• Do not use the device in environments with high static electricity, as this can compromise internal safety measures and increase the risk of overheating or fire.
• If the battery emits an odor, generates heat, or appears abnormal during use, charging, or storage, immediately remove it from the charging device and place it in a sealed, fireproof container or a safe location away from people and flammable materials.
• Discarded batteries can cause fires. Do not heat the controller or battery, or place them near fire.

Battery Leakage Warning

• Battery chemical leakage can cause personal injury and damage to the controller.
• Avoid skin contact with battery chemicals. If contact occurs, wash immediately and thoroughly with soap and water.
• If battery liquid contacts your eyes, DO NOT RUB. Flush eyes immediately with clean running water and seek medical attention.

Motion Warning

Prolonged gaming can cause muscle, joint, skin, or eye discomfort. Follow these guidelines to prevent issues like tendinitis, carpal tunnel syndrome, skin irritation, or eyestrain:

• Avoid excessive play. Take 10-15 minute breaks every hour, even if you don't feel the need. Parents should monitor children's play habits.
• If you experience fatigue or pain in your hands, wrists, arms, or eyes, or symptoms like tingling, numbness, burning, or stiffness, stop playing and rest for several hours before resuming.
• If symptoms persist or you experience other discomfort during or after play, stop playing and consult a doctor.

Compliance and Legal Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-003(B)/NMB-003(B): This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSS(s).

Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits for an uncontrolled environment.

Warranty Against Defects (Australia & New Zealand): This product has a 2-year warranty against manufacturing or material defects. Claims must be made at the place of purchase with proof. Expenses are the consumer's responsibility. See PowerA.com/warranty-ANZ for full conditions.

Distributor Contact Details:

• Australian Customers: ACCO Brands Australia Pty Ltd, Locked Bag 50, Blacktown BC, NSW 2148. Phone: 1300 278 546 | Email: consumer.support@powera.com
• New Zealand Customers: ACCO Brands New Zealand Ltd., PO Box 11-677, Ellerslie, Auckland 1542. Phone: 0800 800 526 | Email: consumer.support@powera.com

Regional Compliance Symbols: Information on symbols like WEEE, CE, UKCA, and Regulatory Compliance Mark is available via web search.

EU/UK Declaration of Conformity: ACCO Brands USA LLC declares that this wireless controller complies with Directive 2014/53/EU and UK Radio Equipment Regulation 2017. The full text is available at PowerA.com/Compliance.

Wireless Rating for EU Compliance: Frequency Range: 2402 MHz – 2480 MHz | Max E.I.R.P.: 6.1 dBm

Electrical Rating Information: Battery: DC3.7V

Support and Warranty

For support with your authentic PowerA accessories, please visit PowerA.com/Support.

2-Year Limited Warranty: Visit PowerA.com for details.

Manufactured For: ACCO Brands USA LLC, 4 Corporate Drive, Lake Zurich, IL 60047. ACCOBRANDS.com | POWERA.com | Made in China.

Contents: MOGA XP5-A Plus Controller | Detachable Gaming Clip | 6.6 ft (2 m) Micro USB to USB Cable | 7.8 in (19.8 cm) Micro USB to USB-C Cable | 11.8 in (30cm) Micro USB to USB Cable | User Guide.