FUFU&GAGA KF180135-01 TV Stand

Model Number: KF180135-01

Version: 03/29/2023

Important Information & Safety

IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or use this product. Follow the manual thoroughly and keep it for further reference.

AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

ANTI-TOPPLE WARNING!

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT! It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.

For regular maintenance and cleaning of the product: For the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Serious or fatal crushing injuries can occur from furniture tip-over. To further reduce the risk of serious injury and death from tip-overs:

ALWAYS install tipover restraint provided.
NEVER put a TV on this product.
NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
NEVER open more than one drawer at a time.
Place heaviest items in the lowest drawers.

This is a permanent label. Do not remove!

Parts and Hardware

Please prepare the following tools and hardware. When installing, please carefully confirm whether each screw corresponds to the manual, as accessories with similar shapes can be distinguished by size.

Hardware List:

A: Screw (Ø5 x 31 mm) - Quantity: 48

B: Cam Lock (Ø15 x 11 mm) - Quantity: 48

C: Wooden Dowel (Ø8 x 30 mm) - Quantity: 8

D: Screw (Ø3 x 10 mm) - Quantity: 4

E: Screw (Ø6 x 30 mm) - Quantity: 9

F: Screw (3 x 10 mm) - Quantity: 3

G: Fastener (Quantity: 48)

H: Fastener (Quantity: 5)

White nut: Quantity: 3

Parts List:

The following numbered parts are used in the assembly:

Part 1: Top Panel

Part 2: Left Side Panel

Part 3: Right Side Panel

Part 4: Internal Divider

Part 5: Internal Divider

Part 6: Back Panel

Part 7: Support Beam

Part 10: Drawer Side Panel (Left)

Part 11: Drawer Side Panel (Right)

Part 12: Drawer Front Panel

Part 13: Drawer Bottom Panel

Part 14: Drawer Back Panel

Part 15: Drawer Front Panel

Part 16: Drawer Front Panel

Part 17: Drawer Side Panel

Part 18: Drawer Back Panel

Part 19: Base Panel

Part 20: Base Panel

Part 22: Leg

Part 23: Drawer Front Panel

Assembly Steps

Step 1

Insert quickfit screw (A) into the designated holes on plate 10 and plate 11. Use a screwdriver to tighten.

Diagram shows screw A being inserted into panels 10 and 11, with a close-up of a screwdriver turning the screw.

Step 2

Attach plate 10 and plate 11 to plate 12. Insert cam lock (B) into plate 12 and turn clockwise to tighten.

Diagram shows panels 10 and 11 connecting to panel 12. Cam locks (B) are inserted into panel 12 and rotated clockwise. A close-up illustrates the cam lock mechanism.

Step 3

Insert quickfit screw (A) into the designated holes on plate 14. Use a screwdriver to tighten.

Diagram shows screw A being inserted into panel 14, with a close-up of a screwdriver turning the screw.

Step 4

Slide plate 13 along the grooves. Attach plate 14 to plate 10 and plate 11. Insert cam lock (B) into plate 10 and 11, and turn clockwise to tighten.

Diagram shows panel 13 sliding into grooves on panels 10 and 11. Panel 14 is then attached to the front edges of panels 10 and 11, secured with cam locks (B) turned clockwise. A close-up shows the cam lock mechanism.

Step 5

Insert quickfit screw (A) into the designated holes on plate 16. Use a screwdriver to tighten.

Diagram shows screw A being inserted into panel 16, with a close-up of a screwdriver turning the screw.

Step 6

Slide plate 13 along the grooves. Attach plate 16 to plate 10 and plate 11. Insert cam lock (B) into plate 10 and 11, and turn clockwise to tighten.

Diagram shows panel 13 sliding into grooves on panels 10 and 11. Panel 16 is then attached to the front edges of panels 10 and 11, secured with cam locks (B) turned clockwise. A close-up shows the cam lock mechanism.

Step 7

Insert quickfit screw (A) into the designated holes on plate 20 and plate 23. Use a screwdriver to tighten.

Diagram shows screw A being inserted into panels 20 and 23, with a close-up of a screwdriver turning the screw.

Step 8

Attach plate 12 and plate 17 to plate 20. Insert cam lock (B) into plate 12 and 17, and turn clockwise to tighten.

Diagram shows panels 12 and 17 connecting to panel 20. Cam locks (B) are inserted into panels 12 and 17 and rotated clockwise. A close-up illustrates the cam lock mechanism.

Step 9

Slide plate 13 along the grooves. Attach plate 23 to plate 12 and plate 17. Insert cam lock (B) into plate 12 and 17, and turn clockwise to tighten.

Diagram shows panel 13 sliding into grooves on panels 12 and 17. Panel 23 is then attached to the front edges of panels 12 and 17, secured with cam locks (B) turned clockwise. A close-up shows the cam lock mechanism.

Step 10

Fix plate 15 and plate 18 to plate 17 using screw (E).

Diagram shows panels 15 and 18 being attached to the side of panel 17 using screws (E). A close-up shows screws (E) being driven into panel 17.

Step 11

Fix drawer runners (DL and DR) to plate 20 and plate 22 using screw (D).

Diagram shows drawer runners labeled DL and DR being attached to the sides of panels 20 and 22 using screws (D). A close-up shows screw D being used to attach a runner.

Step 12

Fix drawer runners (DL and DR) to plate 10 and plate 11 using screw (D).

Diagram shows drawer runners labeled DL and DR being attached to the sides of panels 10 and 11 using screws (D). A close-up shows screw D being used to attach a runner.

Step 13

Fix drawer runners (DL and DR) to plate 10 and plate 11 using screw (D).

Diagram shows drawer runners labeled DL and DR being attached to the sides of panels 10 and 11 using screws (D). A close-up shows screw D being used to attach a runner.

Step 14

Fix slide rail (CL) to plate 2 using screw (D).

Diagram shows a slide rail labeled CL being attached to the inner side of panel 2 using screws (D). A close-up shows screw D being used to attach the rail.

Step 15

Fix slide rail (CR) to plate 3 using screw (D).

Diagram shows a slide rail labeled CR being attached to the inner side of panel 3 using screws (D). A close-up shows screw D being used to attach the rail.

Step 16

Fix slide rail (CR) to plate 4 using screw (D). Flip the plate, then fix slide rail (CL).

Diagram shows slide rail CR attached to panel 4. The panel is then flipped, and slide rail CL is attached to the other side. Close-ups show the attachment process.

Step 17

Fix slide rail (CR) to plate 5 using screw (D). Flip the plate, then fix slide rail (CL).

Diagram shows slide rail CR attached to panel 5. The panel is then flipped, and slide rail CL is attached to the other side. Close-ups show the attachment process.

Step 18

Insert quickfit screw (A) into the corresponding holes in plate 19. Use a screwdriver to tighten.

Diagram shows screws A being inserted into multiple pre-drilled holes on panel 19. Close-ups show a screwdriver turning screw A.

Step 19

Fix leg 22 to plate 19 using screw (E).

Diagram shows legs (22) being attached to the underside of panel 19 using screws (E). Close-ups show screws (E) being driven into panel 19 to secure the legs.

Step 20

Attach plate 7 to plate 19. Insert cam lock (B) into plate 7 and turn clockwise to tighten.

Diagram shows panel 7 being attached to panel 19. Cam locks (B) are inserted into panel 7 and rotated clockwise. A close-up shows the cam lock mechanism.

Step 21

Insert quickfit screw (A) into the corresponding holes in plate 1. Use a screwdriver to tighten.

Diagram shows screws A being inserted into multiple pre-drilled holes on panel 1. Close-ups show a screwdriver turning screw A.

Step 22

Attach plate 7 to plate 1. Insert cam lock (B) into plate 7 and turn clockwise to tighten.

Diagram shows panel 7 being attached to panel 1. Cam locks (B) are inserted into panel 7 and rotated clockwise. A close-up shows the cam lock mechanism.

Step 23

Insert wooden dowel (C) into plates 2, 4, 5, and 3. Attach these panels to plate 19. Insert cam lock (B) into plates 2, 3, 4, and 5, and turn clockwise to tighten.

Diagram shows dowels (C) inserted into panels 2, 4, 5, and 3. These panels are then attached to panel 19. Cam locks (B) are inserted into the appropriate holes on panels 2, 3, 4, and 5 and turned clockwise to secure them. A close-up shows the cam lock mechanism.

Step 24

Slide back plate 6 along the grooves into the assembled unit.

Diagram shows the back panel (6) being slid into grooves on the assembled side and divider panels. Arrows indicate the direction of insertion.

Step 25

Insert wooden dowel (C) into plates 2, 4, 5, and 3. Attach these panels to the top panel (1). Insert cam lock (B) into plates 2, 3, 4, and 5, and turn clockwise to tighten.

Diagram shows dowels (C) inserted into panels 2, 4, 5, and 3. These panels are then attached to the top panel (1). Cam locks (B) are inserted into the appropriate holes on panels 2, 3, 4, and 5 and turned clockwise to secure them. A close-up shows the cam lock mechanism.

Step 26

Align the drawer runners and slide all drawers into the unit.

Diagram shows the assembled TV stand with drawers being slid into their respective slots. Arrows indicate the direction of insertion. A close-up shows drawer runners aligning.

Step 27

Attach fasteners (G and H) to the bottom of the TV stand legs.

Diagram shows fasteners labeled G and H being attached to the bottom of the TV stand legs.

Warranty Information

WARRANTY CLAIMS

There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
Before making a claim, please call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is an item out of stock, we will reply with a shipping date.
The product must be used in accordance with the instructions provided. For health reasons.
For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

Failure to follow the furniture instructions will invalidate the warranty.
Damage during installation is not covered, but damage during transportation is included.

Scope of Responsibility

FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
After use, damage and scratches of the furniture are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas:

Sheet parts: 1 month from the date of purchase.
Electrical parts: 1 month from the date of purchase.

Returns

CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?

PLEASE FOLLOW THE BELOW INSTRUCTIONS:

If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

If your item is defective in any way, i.e. it doesn't work but you can't identify why, in the first instance, please call us.

DAMAGED ITEMS

If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.

In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive a credit for the return.

Final Safety Warning

Serious or fatal crushing injuries can occur from furniture tip-over.

To further reduce the risk of serious injury and death from tip-overs:

(Note: The German text on the last page is a translation of the above warning and is omitted as per the primary language requirement.)

	FUFU&GAGA KF020434-01 TV Cabinet Assembly Instructions Comprehensive assembly guide for the FUFU&GAGA KF020434-01 TV Cabinet, including safety warnings, parts list, tools required, and step-by-step instructions for building a modern entertainment center. Covers warranty and returns information.
	FUFU&GAGA Display Cabinet Assembly Instructions This document provides detailed assembly instructions for the FUFU&GAGA Display Cabinet, including a list of parts, tools required, and step-by-step guidance for assembly. It also includes important safety information and warranty details.
	FUFU&GAGA Sideboard Assembly Instructions and Warranty Information Comprehensive guide for assembling the FUFU&GAGA Sideboard, including important safety information, parts list, step-by-step instructions, and warranty/returns policy.
	FUFU&GAGA Display Cabinet Assembly Instructions Comprehensive assembly guide for the FUFU&GAGA Display Cabinet, detailing tools required, parts identification, step-by-step assembly instructions, important safety warnings, warranty information, and returns policy.
	FUFU&GAGA Sideboard Assembly Instructions and Manual Step-by-step assembly guide for the FUFU&GAGA Sideboard (Model KF260080-01). This manual provides detailed instructions, a parts list, safety warnings, maintenance tips, warranty, and returns information for assembling your new furniture.
	FUFU&GAGA LJY-KF020283-01 4-Door Storage Cabinet Assembly Instructions Comprehensive assembly guide for the FUFU&GAGA LJY-KF020283-01 4-door storage cabinet, detailing all parts and step-by-step construction for safe and proper setup.
	FUFU&GAGA Night Table Assembly Instructions and Safety Guide Comprehensive assembly instructions, safety warnings, and maintenance tips for the FUFU&GAGA Night Table / Shoe Storage Cabinet (Model KF020233-01). Learn how to safely build and care for your furniture.
	FUFU&GAGA KF150167-01 Assembly Instructions and Product Manual Comprehensive assembly guide for the FUFU&GAGA KF150167-01 furniture, featuring detailed steps, parts list, hardware identification, safety warnings, and warranty information.