Casio Watch Module User Manual

Module Numbers

The following module numbers are covered in this manual:

705, 706, 707, 708, 709, 1300, 1309, 1311, 1330, 1331, 1332, 1333, 1334, 1335, 1336, 1342, 1344, 1345, 1346, 1347, 1360, 1362, 1369, 1370, 1373, 1398, 1399, 1701, 1710, 1711, 1747, 1770, 1771, 1782, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 2799, 3363, 3378, 3711, 3712, 3716, 4328, 4370, 4393, 4394, 4747, 5025, 5044, 5049, 5058, 5116, 5125, 5128, 5167, 5180, 5199, 5206, 5207, 5218, 5223, 5237, 5249, 5250, 5284, 5339, 5340, 5341, 5342, 5343, 5352, 5358, 5361, 5364, 5373, 5375, 5383, 5393, 5436, 5458, 5474, 5507, 5532.

The title "Руководство по пользованию функциями часов" translates to "User Manual for Watch Functions".

Important Information - Read First

Water Resistance

For all watch categories, the following are prohibited:

• Pressing buttons underwater.
• Moving the hands underwater.
• Unscrewing the crown underwater.

If the watch is exposed to salt water, rinse it thoroughly and dry it. Do not wear watches with leather straps while swimming. Avoid prolonged contact of leather straps with water.

Watches are classified into levels (from I to V) according to their water resistance. Check your watch's level using the table below to determine correct usage.

Notes

• I Watches are not water-resistant. Avoid any moisture ingress.
• II WR (Water Resistant) means the model is water-resistant according to ISO 2281. Brief contact with water will not cause any problems.
• III With 5 Bar (50 meters) water resistance, the watch can withstand water pressure as indicated and can therefore be used during showers and brief swimming.
• IV 10 Bar (100 meters) water resistance means the watch can be used during normal swimming and snorkeling.
• V 20 Bar (200 meters) water resistance means the watch can be used for scuba diving (except for depths requiring a helium-oxygen mixture).

When using the product in conditions of rapid temperature changes, slight condensation may form on the inside of the glass. This phenomenon is due to the laws of physics and is not a defect.

CASIO COMPUTER CO., LTD. is not responsible for any damage that may occur from the use of this watch, and does not accept any claims from third parties.

General Notes

Your watch may differ slightly from the illustrations in this manual.

Note on Screw-Lock Crown

Some water-resistant watch models are equipped with a screw-lock crown. To pull out such a crown, you must unlock it by turning it in the direction indicated [arrow symbol]. Do not use excessive force when pulling out the crown, as this may cause damage. Please note that the watch is no longer protected from water and moisture when the crown is pulled out. After completing all operations using the crown, return it to its original position and lock it.

Setting the Current Time

For Modules 1362, 1398, 1770, 2799, 3378, 4370

Pull out the crown. Rotate it to set the hands to the current time. Push the crown back to its original position.

[Diagram showing watch and crown]

For Modules 705, 706, 1300, 1311, 1330, 1344, 1360, 1399, 1747, 1771, 1782, 4328, 4394, 4747, 5049, 5284, 5361, 5364, 5375, 5577

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. Set the minute hand 4-5 minutes ahead of the current time, and then move it back.
3. When the time signal sounds, push and lock the crown.

[Diagrams showing watch faces and crown positions for module group]

For Modules 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. For more precise time setting, move the minute hand back 4-5 minutes from the desired time, then move it forward to the current time.
3. Push the crown back to its original position to resume time display.

[Diagram showing crown positions: normal, first click (date setting), second click (time setting), and date display '30']

Setting the Date

To ensure the date changes at midnight, do not set the date between 8:00 PM and 2:00 AM.

1. Pull out the crown to the first click.
2. Rotate it to set the desired date.
3. Push the crown back to its original position.

[Diagram showing crown positions and date display '30' for modules 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532]

For Modules 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

Setting the Current Time

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. For more precise time setting, move the minute hand back 4-5 minutes from the desired time, then move it forward to the current time.
3. Push the crown back to its original position to resume time display.

[Diagrams showing crown positions and day/date displays 'SUN 30' and 'WED 30' for module groups]

Setting the Date and Day of Week

To ensure the date and day of week change at midnight, do not set the date between 8:00 PM and 2:00 AM.

1. Pull out the crown to the first click.
2. Set the date by rotating the crown counter-clockwise.
3. Set the day of the week by rotating the crown clockwise. Days of the week are indicated in English or Spanish.

4. Push the crown back to its original position.

Watches with Backlight

Press and hold button L [⛭] to illuminate the watch face.

Depending on the watch model, the backlight duration is 2 to 3 seconds, or 1 second, or while button L is pressed (module 5577).

Depending on the watch model, the face illumination is by electroluminescent (EL) elements or LEDs. EL elements lose power after prolonged use.

Frequent use of the backlight reduces battery life.

Activating the backlight for an extended period or with a low battery charge may cause the watch hands to stop moving for a while.

[Diagrams showing watch faces with backlight button L and crown]

Watches with Rotating Bezel

Rotate the bezel to align a mark with the minute hand. After some time, you can tell how much time has passed since you aligned the mark with the minute hand.

[Diagram of a watch with a rotating bezel, indicating bezel for measuring elapsed time]

Technical Specifications

Specifications are subject to change without prior notice.

Product Information

Product Name: Electronic / Electro-mechanical Quartz Wristwatch (Men's/Women's)

Brand: CASIO

Manufacturer: CASIO COMPUTER Co., Ltd.

Manufacturer Address: 1-6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Importer: OOO 'Casio', 127015, Russia, Moscow, Butyrskaya St., bld. 77

Warranty Period: 2 years

Address of authorized organization for claims: Indicated on the warranty card.