Casio Watch User Manual

Water Protection

This section provides essential information regarding water resistance for Casio watches.

General Precautions: For all watch categories, it is prohibited to:

• Press buttons underwater.
• Adjust hands underwater.
• Unscrew the crown underwater.

If your watch is exposed to salt water, rinse it thoroughly and dry it completely. Avoid wearing watches with leather straps while swimming or during prolonged contact with water.

Watches are classified by water resistance levels (I to V) according to their protection against water. Refer to the table below to determine the correct usage for your watch.

Notes on Water Resistance:

• Level I: Watches are not water-resistant. Avoid any moisture.
• Level II: WR (Water Resistant) indicates the model is waterproof according to ISO 2281. Brief contact with water will not cause problems.
• Level III: Watches with 5 Bar (50 meters) water resistance can withstand water pressure equivalent to that experienced during showering and brief swimming.
• Level IV: Watches with 10 Bar (100 meters) water resistance can be used for normal swimming and snorkeling.
• Level V: Watches with 20 Bar (200 meters) water resistance can be used for scuba diving, excluding depths requiring helium-oxygen gas mixtures.

Condensation: Under conditions of rapid temperature changes, slight condensation may form on the inside of the glass. This is a normal physical phenomenon and not a defect.

Disclaimer: CASIO COMPUTER CO., LTD. is not responsible for any damage that may occur from the use of these watches and does not accept claims from third parties.

Crown Operation

Your watch may differ slightly from the illustrations in this manual.

Screw-Lock Crown: Some water-resistant models are equipped with a screw-lock crown.

• To pull out the crown, you must first unlock it by turning it in the direction indicated in the illustration. Do not use excessive force when pulling out the crown, as this may cause damage.
• Note that water and moisture resistance is lost when the crown is pulled out. After performing any operations with the crown, ensure it is returned to its original position and locked.

Illustration description: A watch face showing the crown. An arrow indicates the direction to turn the crown to unlock it.

Setting Current Time

Modules 1362, 1398, 1770, 2799, 3378, 4370

Pull out the crown. Rotate it to set the hands to the current time. Push the crown back to its original position.

Illustration description: A watch face with hands and a crown, labeled "Crown".

Modules 705, 706, 1300, 1311, 1330, 1344, 1360, 1399, 1747, 1771, 1782, 4328, 4394, 4747, 5049, 5284, 5361, 5364, 5375, 5577

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. For precise time setting, advance the minute hand 4-5 minutes ahead of the current time, then return it to the correct position.
3. Push the crown back in and lock it to resume time display.

Illustration description: Two watch faces are shown. The first is a standard analog watch face with hands and a crown. The second shows a watch face with a date window, indicating the crown's positions for date and time setting. Module numbers 5284, 5361, 5364, 5375, 5577 are listed.

Modules 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. For more precise setting, move the minute hand 4-5 minutes back from the desired time, then return it to the correct value.
3. Push the crown back to its original position to resume time display.

Illustration description: A watch face with a date window. The crown is shown in its normal position (first click for date setting) and second click (time setting). Arrows indicate rotation.

Modules 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. For more precise setting, move the minute hand 4-5 minutes back from the desired time, then return it to the correct value.
3. Push the crown back to its original position to resume time display.

Illustration description: Two watch faces are shown. The left shows a watch with a date window (e.g., 'SUN 30') and a crown, indicating positions for date/day and time setting. The right shows a similar watch face with a different day display (e.g., 'WED 30'). Module numbers 709, 1333, 1347, 3716 are listed.

Setting Date and Day of the Week

To ensure the date and day of the week change at midnight, do not perform date settings between 8:00 PM (20:00) and 2:00 AM.

1. Pull out the crown to the first click.
2. Set the date by rotating the crown counter-clockwise.
3. Set the day of the week by rotating the crown clockwise. Days of the week are shown in English or Spanish.

4. Push the crown back to its original position.

Watches with Backlight

Press and hold the 'L' button to activate the watch's backlight.

• Backlight duration varies by model: 2 to 3 seconds, 1 second, or until the 'L' button is released (e.g., Module 5577).
• Backlight illumination is provided by electroluminescent (EL) elements or LEDs. EL elements may lose brightness after prolonged use.
• Frequent use of the backlight reduces battery life.
• Activating the backlight for extended periods or when the battery charge is low may cause the watch hands to stop moving temporarily.

Illustration description: Watch faces showing the location of the 'L' button (backlight) and the crown.

Watches with Rotating Bezel

Rotate the bezel to align its marker with the minute hand. After some time, you can tell how much time has passed since the marker was aligned with the minute hand.

Illustration description: A watch face with a rotating bezel. A marker on the bezel is aligned with the minute hand, indicating elapsed time.

Technical Specifications

Technical specifications are subject to change without prior notice.

Product Information

Product Name: Electronic / electro-mechanical quartz wristwatches (men/women)

Brand: CASIO

Manufacturer: CASIO COMPUTER Co.,Ltd.

Manufacturer Address: 1-6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Importer: OOO "Kasio", 127015, Russia, Moscow, Butyrskaya str., bld. 77

Warranty Period: 2 years

Authorized Organization for Claims: As indicated on the warranty card.