Fortin EVO-ALL Installation Guide

Model Compatibility: Jeep Compass (2020-2021) with Automatic Transmission and Push-to-Start

Document Revision: 20250113

Guide Number: 103241

Introduction

This guide provides instructions for the standalone installation of the Fortin EVO-ALL module for automatic transmission vehicles. It is compatible with Jeep Compass models from 2020 to 2025 equipped with a push-to-start system.

Important Note: This product is ONLY compatible with automatic transmission vehicles.

Vehicle Functionality Support

The EVO-ALL module supports various vehicle functions, including:

Immobilizer bypass
T-Harness
Lock
Unlock
Arm
Disarm
Parking Lights
Trunk (open)
Tachometer
Heated mirror
Comfort Group / Comfort AUX. 1
Rear defrost
Door Status
Hood Status*
Remote Start Status
OEM Remote Monitoring
Foot-Brake Status

*Hood Status: The hood pin switch must be installed. If the vehicle can be remote started with the hood open, set Function A11 to OFF.

Firmware Information

Minimum Firmware Version Required: 68.[02]

To update the firmware and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Parts Required (Not Included)

1x THAR-CHR7
1x THAR-CHR6

Wiring Diagrams

Detailed wiring diagrams are provided for:

Wire to Wire Diagram
THARNESS Diagram (T-Harness)

Refer to specific pages for THARNESS THAR-CHR7 and THARNESS THAR-CHR6 diagrams.

Mandatory Installation Components

Hood Pin: This is a mandatory safety element and must be installed. If the vehicle can be remote started with the hood open, set Function A11 to OFF.
Valet Switch: This is an essential security element and must be installed.

Warning: This module must be installed by a qualified technician. Incorrect wiring can cause permanent damage to the vehicle.

Configuration Options

Stand Alone Configuration

OEM Remote Stand Alone: Program bypass option for original remote.
OEM Remote: Program bypass option with original remote.
RF KIT Antenna: Program bypass option with RF Kit antenna.

Remote Starter Functionality

To remote start or stop the vehicle, press the OEM remote's Lock button 3 times.

Programming Procedures

DCRYPTOR Programming Procedure

Follow these steps to program the module using the DCRYPTOR:

Press and hold the programming button, then insert the 4-Pin (Data-Link) connector. Observe LED illumination.
Release the programming button when the LED is BLUE. If the LED is not solid BLUE, repeat the step.
Insert remaining connectors.
Press the Push-to-Start button once to turn ON the ignition.
Press and release the programming button once. The BLUE LED will flash rapidly.
Press the Push-to-Start button once to turn OFF the ignition. The BLUE LED will turn OFF, and the RED LED will turn ON.
Press the Push-to-Start button once to turn ON the ignition. The YELLOW LED will turn ON, and the RED LED will turn OFF.
Repeat the process approximately 10 times until the RED and YELLOW LEDs alternate at ignition OFF.
Disconnect all connectors, including the Data-Link (4-pins) connector.
Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCRYPTOR menu.

After programming, reconnect the Data-Link connector and all other connectors.

Optional RF-Kit Programming

Follow the specific instructions for programming the RF-KIT Series 4 or Series 9.

Program Bypass Option: H2 (Supported RF-KITS enable, H2 Fortin 2)
Activation RF Kits: Supported H2 Fortin 2

Refer to the guide for detailed step-by-step instructions involving button presses and LED indicators for RF-kit programming.

Remote Starter Verification

Test the remote starter by initiating a remote start sequence.

Notes and Warnings

12V Battery: The T-Harness current is limited to 5 AMP MAXIMUM. If a parking lights (+) wire requiring more than 5A is used, connect the remote starter's power directly to the vehicle's battery with an appropriate fuse.
Some remote starters cannot be powered through Data-Link. Connect the 12V power wire directly to the T-Harness in such cases.
Safety Elements: The hood pin and valet switch are mandatory safety elements.
Installation Responsibility: Installation is the sole responsibility of the installer. Incorrect installation may lead to vehicle damage.
Information Accuracy: Information provided is a guide and may change without notice. Always refer to www.fortinbypass.com for the latest version.

Technical Support

Phone: 514-255-HELP (4357) or 1-877-336-7797

Website: www.fortinbypass.com

	Fortin EVO-ALL Installation Guide for Lincoln Aviator (2020-2024) Push-to-Start Comprehensive installation guide for the Fortin EVO-ALL module in a Lincoln Aviator (2020-2024) with push-to-start functionality. Covers wiring diagrams, configuration options, and remote starter functionality.
	Fortin EVO-ALL Installation Guide for Nissan Sentra (Push-to-Start) Installation guide and wiring diagram for the Fortin EVO-ALL remote starter and data bypass module for Nissan Sentra vehicles equipped with a Push-to-Start system. Includes programming procedures, functionality details, and technical specifications.
	Fortin EVO-ONE Installation and Programming Guide for Toyota Corolla This guide provides detailed instructions for installing and programming the Fortin EVO-ONE remote starter and bypass module for Toyota Corolla models, including 2023-2024 Hatchback and 2023 Sedan Push-to-Start variants. It covers wiring, DCryptor programming, key bypass procedures, and remote starter functionality.
	Fortin EVO-ALL Stand Alone Installation Guide for Lexus UX250H Comprehensive installation guide for the Fortin EVO-ALL remote starter and bypass module for the 2019-2024 Lexus UX250H, covering wiring, programming, and functionality.
	Fortin EVO-ALL Installation Guide for Jeep Cherokee (2019-2021) This guide provides detailed instructions for installing the Fortin EVO-ALL remote start and bypass module in a Jeep Cherokee (2019-2021 Tip-key). It covers wiring, programming procedures, vehicle compatibility, and important safety notes.
	Fortin EVO-ALL Stand Alone Installation Guide for Volkswagen Golf (2019-2022) This guide provides detailed instructions for the stand-alone installation of the Fortin EVO-ALL interface module for Volkswagen Golf models (2019-2022) equipped with push-to-start and automatic transmissions. It covers wiring configurations, programming procedures, functionality, and important safety warnings.
	Fortin EVO-ALL Installation Guide for Cadillac CT4 (2020-2023) Push-to-Start Comprehensive installation guide for the Fortin EVO-ALL remote starter and bypass module in a 2020-2023 Cadillac CT4 with Push-to-Start. Includes wiring diagrams, programming steps, function details, and safety warnings.
	Fortin EVO-ALL Stand Alone Installation Guide for Cadillac CT5 (2020-2023) Comprehensive installation guide for the Fortin EVO-ALL remote starter and bypass module for Cadillac CT5 vehicles (2020-2023) with Push-to-Start ignition. Includes wiring diagrams, programming procedures, and function descriptions.