Allmatic 24CBA BOX Battery Kit for Sliding Gates

General Safety and Regulatory Incompatibility

Any use of this product other than its intended purpose is prohibited. The manufacturer is not liable for damage resulting from improper use or installation not complying with this manual. All operations must be performed by experienced, qualified personnel. Ensure compliance with all applicable local, regional, and national regulations. Failure to comply can result in death, serious injury, or equipment damage.

Risk of Electric Shock, Explosion, or Electric Arc: Shut down all equipment before any maintenance. Use a calibrated voltmeter to verify power is off. Ensure cable entries are sealed. Use only specified voltage. Do not disassemble, repair, or modify. Not suitable for explosive atmospheres.

Risk of Electric Shock and/or Fire: Do not expose to liquids. Maintain specified temperature and humidity ranges. Use only compatible accessories. Use appropriate cable cross-sections and torque specifications. Ensure electrical cables do not contact hot or moving parts.

Risk of Overheating and/or Fire: Do not use with loads other than specified. Power lines and output connections must be properly wired and fused as required.

Battery Safety

DANGER - RISK OF OVERHEATING, EXPLOSION, FIRE OR BURN: Handle intact batteries carefully in a ventilated area. Do not smoke, eat, or drink during assembly. Do not expose to temperatures above 100°C (60°C recommended). Avoid short circuits, crushing, and heat sources. Do not disassemble, puncture, heat, or wet batteries. Do not dispose of batteries in fire. Avoid contact with water, oxidizing agents, and alkalis. Keep batteries out of reach of children. If the battery compartment does not close securely, suspend use. Seek immediate medical attention if batteries are swallowed or inserted into body orifices. Use only specified battery types to avoid explosion risk.

Product Disposal

Disassembly must be performed by qualified personnel. The product should not be disposed of as unsorted waste but sent to separate collection facilities for recovery and recycling. Check local regulations for proper disposal or return the product to the seller. The product contains various materials, some of which may be hazardous. Improper disposal can lead to environmental and health damage and may incur penalties.

Warranty

The manufacturer's warranty is valid from the date printed on the product and covers free repair or replacement of defective parts due to material or production errors. It does not cover damage from external agents, lack of maintenance, overload, normal wear, installation errors, or tampering. The manufacturer is not responsible for malfunctions due to environmental interference, such as electromagnetic disturbances.

Installation and Connections

Read safety warnings before installation. Switch off the control unit. Connect the 24CBA BOX to the control unit using provided cables, ensuring correct polarity. Switch on the control unit. Connect batteries to the 24CBA BOX with provided cables, ensuring correct polarity. Place the 24CBA BOX and batteries as indicated in the figures, depending on the gear motor model.

Testing and Commissioning

After connecting the buffer battery:

• Connect the automation to the mains and verify charging voltage on the battery charger board.
• Perform a complete open and close maneuver to check system operation on mains power.
• Disconnect from mains and verify the control unit remains powered. Perform a complete open and close maneuver to check operation on battery power.
• Reconnect to the mains. Wait a few hours before further checks.

Maintenance

Maintenance must be performed by qualified personnel. The buffer battery requires no maintenance but should be disconnected and stored in a dry place during long periods of non-use. Batteries need replacement when their capacity significantly reduces due to aging. Every 12 months, check electrical connections and perform a functional system check.

Technical Characteristics

• Commercial Name: 24CBA BOX
• Battery Type: Maintenance-free sealed lead-acid accumulators
• Construction: Electronic device to be incorporated
• Maximum Charging Voltage: 28 V
• Maximum Current Available: 1 A
• Storage Capacity: 1.3 Ah
• Autonomy: Approx. 18 hours in stand-by; Approx. 5 minutes with 4A load (approx. 10 maneuvers)
• Time to Complete Charging: Approx. 16 hours
• Battery Life: Estimated 4-5 years
• Operating Temperature Range: Discharge: -15 to +50°C; Charge: 0 to +40°C; Storage: -15 to +40°C
• Protection Rating: IP 20 (for use in control units, gear motors, or protected environments)

Note 1: Technical characteristics are at 20°C (± 5°C). Stand-by autonomy is for the control board only. Automation autonomy is estimated for a 5m sliding gate without impediments. Battery performance is influenced by temperature, current consumption, charge state, and age.

Electrical Connections Guidelines

Use copper conductors only. Avoid exposed copper wires. Ensure correct cable cross-sections and tightening torques as specified.

EC Declaration of Conformity

Allmatic s.r.l. declares that the 24CBA BOX complies with the essential requirements of Directive EMC 2014/30/UE.