Jensen CAR710-4 Quick Start Guide

Installation

Before You Start

• Disconnect the negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures (e.g., direct sunlight) or where it would be subject to dust, dirt, or excessive vibration.

Mounting Hardware: TRIM RING, MOUNTING SCREWS (T5 x 6mm). Use 2 or 3 screws to affix the monitor to the bracket.

Control Locations

The radio display features the following functions and controls:

• (1) RESET button
• (2) VOL- / VOL+ buttons (Power/Mute)
• (3) SOURCE button
• (4) VOICE ACTIVATION BUTTON

Wiring Diagram - Inputs/Outputs

The unit features the following connections:

• VIDEO IN
• CAMERA IN
• AV IN L
• AV IN R
• SUB PREAMP OUT (Green RCA)
• REAR LEFT PREAMP OUTPUT (White RCA)
• FRONT LEFT PREAMP OUTPUT (White RCA)
• FRONT RIGHT PREAMP OUTPUT (White RCA)
• REAR RIGHT PREAMP OUTPUT (White RCA)
• RADIO ANTENNA
• MIC (for external microphone)
• 20-PIN Connector

Fuse: The unit uses one 15A ATC mini style fuse located on the power connector. Replace with the same 15A ATC style fuse.

Wiring Notes:

• Subwoofer output: The Subwoofer preamp audio output (Green RCA) is active in all audio modes.
• Rear camera input: A rear view camera (not included) can be used with the Camera input.

Main Menu & Operations

Main Menu

In the main menu, press the desired icon to enter the corresponding mode: Radio, USB, BT Phone, BT Audio, Android Auto, Apple CarPlay, AV In, Equalizer, Settings.

Tuner Operation

The tuner operation screen displays the current frequency, preset stations, AM/FM band, and controls for Seek Tune Up/Down, Keypad access, and EQ settings.

USB Operation

From the main menu, touch the USB icon. The screen shows playback controls (Play/Pause ▶️/⏸️), track information, track navigation (Track Up/Down ⬆️/⬇️), List ☰, Repeat ?, Random Search ?, and EQ settings. Note: Video playback is enabled only when the vehicle is in park and the parking brake is engaged.

Bluetooth Operation

Pairing a New Device: The unit broadcasts a pairing signal when no devices are connected. Complete the pairing sequence from your Bluetooth device. The device name is "CAR710-4".

Connecting: The head unit can be set to automatically connect to the last connected device.

Bluetooth Phone: From the main menu, touch the Bluetooth icon. The screen provides a keypad for dialing, controls to connect/end calls ?/?, transfer audio between the head unit and mobile phone, and controls for streaming audio (Play/Pause ▶️/⏸️, Previous/Next Track ◀️/▶️).

Audio Operation

Press the Settings icon to adjust Fader and Balance controls, Equalizer (8-Band Tone Control and 8 Presets EQ Settings), Subwoofer settings, and Loudness.

Apple CarPlay Operation

Select Apple CarPlay from the Main Menu. If an iPhone is connected via USB, its apps will mirror onto the screen. The CAR710-4 will automatically switch to Apple CarPlay mode when the iPhone USB cable is inserted.

Android Auto™ Operation

Select Android Auto from the Main Menu. If an Android Phone is connected via USB, the Android Auto interface will mirror onto the screen. The CAR710-4 will automatically switch to Android Auto mode when the Android Phone USB cable is inserted.

General Operation (Setup)

From the Main Menu, select Setup to access settings for General, Audio, Display, and Others. Options include Time Format (12/24 Hour), Beep On/Off, Radio Region, Right Hand Drive, Time Alignment, Loudness, Subwoofer, and Subwoofer Gain.

Warranty Information

Jensen Limited Warranty

Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of original purchase. A limited 3-year warranty is available when purchased from and professionally installed by an authorized Jensen dealer (proof of purchase and installation required).

What is covered: All defects in material and workmanship.

What is not covered: Software, installation/removal costs, damage from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair, or damage during return shipment.

To obtain service: Check the troubleshooting guide. Pack the product carefully (preferably in original packaging) and ship it by prepaid transportation with a copy of the original receipt to an authorized service center. Include a written description of the problem, your name, UPS shipping address (no P.O. Boxes), and a daytime phone number.

Contact Jensen: Toll-free at (888) 921-4088 (Monday-Friday, 9:00 a.m. to 5:00 p.m. EST) or email at cs@jensenmobile.com.

This warranty is exclusive and in lieu of all other warranties. Namsung America Inc. is not liable for indirect, incidental, or consequential damages.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For more information and to register your warranty, visit www.jensenmobile.com/register.html. Follow Jensen on Facebook, Instagram, and Twitter @JensenAudio.

© 2024 Namsung America Inc. All rights reserved.

BUCAM350 Universal License Plate Style Camera

What's in the box

• Product Sheet
• BUCAM350 License plate style camera
• Power Cable w/ Fuse, Video Cable

Mounting the Camera

Position the camera on the license plate top screws for the best viewing angle. Avoid placing it directly next to or under a reverse/backup/license lamp, as this may blind the camera at night. Before drilling, determine the best way to run power wires to the reverse lights and the extension cable through the car, ensuring no interference with safety equipment or trunk releases. The camera should lay flat against the mounting surface for proper installation.

Wiring Options

• OPTION 1: Connect camera power wire to the vehicle's reverse lamp: Locate the reverse lamp in the tail light assembly. Attach the red wire to the positive 12-volt wire from the reverse lamp using a crimp connector or soldering tool. The red power wire on the video RCA cable will not be needed. Cap or tape off bare wires to prevent interruption. Attach the black wire to ground (-). Run the video cable to the receiver/monitor and connect the yellow RCA end to the camera and the other end to the video source.
• OPTION 2: Connect camera power wire to receiver/monitor power: From the camera location, connect the red power wire from the power cable to the red power wire of one end of the video cable. Attach the black wire to ground. Run the video cable to the receiver/monitor. Connect the yellow RCA end of the video cable to the camera and the other end to the video source. From the video source location, connect the red power wire from the video cable end to the reverse wire lead on the video source.

Camera Specifications

• Image Sensor: CMOS, OV 7955
• Power: 12V DC, Negative Ground
• Power Consumption: < 1 Watt
• Effective Pixels: 672H x 492V
• Video Format: NTSC
• Lux: <0.5
• White Balance: Auto
• Viewing Angle: 170 Degrees
• IP Rating: IP67
• Operating Temperature: -30°C to +70°C
• Plate material: Stainless Steel SUS304
• Camera Body: Plastic

Blue Loop Feature

The camera includes a blue loop wire that, when connected, allows backup lines to appear on the screen. If you do not want these lines, cut the blue loop wire. After cutting, ensure the two wires are insulated to prevent shorting.

Dual Electronics Corp. Limited Warranty

Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. This warranty is extended to the original retail purchaser for products purchased from an authorized JENSEN/Dual/Axerra dealer and used in the U.S.A.

What is covered: All defects in material and workmanship.

What is not covered: Software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair, or failure to follow instructions, or damage occurring during return shipment.

To obtain service: Before calling for service, check the troubleshooting guide in your owner's manual. If service is required, carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number.

Contact Dual Electronics: Call toll-free at 1-866-382-5476 or email at cs@dualav.com.

This warranty is exclusive and in lieu of any and all other warranties, expressed or implied. Dual Electronics Corp. shall not be liable for indirect, incidental, or consequential damages.

© 2023 Dual Electronics Corp. Printed in China.