MILESEEY TP2 PLUS Thermal Imager

Warranty Statement

For complete products manufactured by Mileseey, a two-year warranty is provided from the date of initial purchase, under conditions of normal storage, reasonable use, and maintenance. The warranty period for accessories is three months.

This warranty is non-transferable and does not apply to products damaged due to misuse, negligence, accidents, or abnormal operating conditions. If defects occur, the product must not be used further or repaired privately to prevent further damage. The purchaser must immediately report the product defect to Mileseey; otherwise, this warranty will not apply.

If, upon inspection by Mileseey, the product or accessory is found to be faulty, the user may contact Mileseey's after-sales service department within the warranty period to negotiate repair or replacement.

1.2 Quality Assurance

The quality management system has been certified according to the ISO9001 standard. Mileseey reserves the right to modify or improve any product without prior notice.

Safety Instructions

Warning:

• Before using cleaning solutions, read all applicable Material Safety Data Sheets (SDS) and warning labels on the containers.
• Do not place the product in high-temperature environments exceeding 60°C or in low-temperature environments below -20°C. The device supports operation while charging.
• It is recommended to charge the device in room temperature conditions and when it is turned off. Do not charge in high-temperature environments above 40°C or in low-temperature environments below 0°C.
• Do not operate the device in high-temperature environments exceeding 50°C or in low-temperature environments below -10°C.
• The relative humidity for the device's use is 10% to 95%, non-condensing.
• Do not arbitrarily disassemble or modify the infrared thermal imager.

Applicability: Class B digital devices.

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

2. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Frequency range of WLAN radio module: 5.15~5.85GHz. Maximum power of WLAN radio module: 13dBm (Only for EU).

Mileseey Technology Co., Ltd. declares that the radio equipment type TP2 PLUS is in compliance with Directive 2014/53/EU, 2011/65/EU.

To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user's body and the handset, including the antenna.

Caution:

• Do not use the product under conditions that exceed the specified environmental requirements. Refer to the product specification sheet for specific environmental requirements.
• Do not apply cleaning solutions or similar liquids directly onto the thermal imager, cables, or other components.
• Be extremely cautious when cleaning the infrared lens. The lens has a delicate coating that can be damaged by rough materials like paper towels or excessive force.
• Avoid pointing the infrared thermal imager towards strong light sources or devices emitting laser radiation, regardless of whether the lens cap is on. This can affect the accuracy of the thermal imager and potentially damage its detector.

User Notice

3.1 Calibration

To ensure the accuracy of temperature measurements, it is recommended to calibrate the thermal imager annually. This calibration can be performed either by Mileseey or a third-party organization.

3.2 Accuracy

To achieve highly accurate results, wait for 5 minutes after turning on the thermal imager before beginning temperature measurements (this includes switching temperature ranges).

3.3 Documentation Updates

Manuals are updated several times a year, and notices about key product changes are regularly issued. To access the latest manuals and notifications, please visit the Mileseey official website.

3.4 Applicability

This manual applies to all products within a series, meaning some functions described may not be applicable to a specific model within the series.

3.5 Disposal of Electronic Waste

2012/19EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, see: www.recycle-this.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point.

Component Guide

4.1 Front View

The front view shows the Infrared Imager Lens, Power Button, Digital Imager (TP2 Plus only), and Battery Indicator light.

4.2 Back View

The back view shows the Back Clamp.

4.3 Side View

The side view shows the USB Interface.

Quick Operating Guide

1. Charging: Use a 5V 2A power adapter and USB cable to charge the device. Please charge the device in room temperature conditions.
2. Power On: Press and hold the power button to turn on the device.
3. Locate the Target: Aim the thermal imager at the object of your interest.
4. Capturing Images: Use the Mobile App on your phone to capture images by pressing the imager button and record videos by pressing the video button.
5. APP Analysis: Open the accompanying App for the thermal imager, navigate to the gallery, select the picture for secondary analysis, and proceed with the analysis.

APP Description

6.1 App Overview

The "Thermal TP Series" app, for secondary analysis, is compatible with the TP series of wireless thermal imagers. It allows viewing images in five different modes (infrared, visible light, dual-light fusion, picture-in-picture) with the ability to customize and switch between them. The app features capabilities for pseudocolor switching, photography, video recording, and custom temperature analysis with points, lines, and frames.

6.2 App Connectivity

1. Press and hold the power button to turn on the device and ensure the Bluetooth function of your smartphone is enabled.
2. Open the "Thermal TP Series" app.
3. Click on the device you want to connect to.
4. A pop-up window will prompt: "Thermal TP Series wants to join the wireless network TP2. Cancel or Join?" Click on "Join" to successfully connect (this step is only necessary for iPhone models).

6.3 Introduction of the Main User Interface

The main user interface displays various icons and their functions:

6.4 Setting Interface

Measurement Range: Options for low and high temperature ranges are available; supports automatic switching of temperature ranges.

• Auto Power-Off: Supports custom settings for no auto shut-down, or automatic shut-down after 10 or 20 minutes.
• Factory Reset: Tap to perform a factory reset. After resetting to factory settings, all device information will be erased.
• Battery Capacity: Displays remaining battery life.
• Device Info: Allows viewing of the device model, PN (Part Number), SN (Serial Number), and firmware version number.

Cleaning

7.1 Clean the exterior casing, cables, and other components of the thermal imager.

Warning:

Avoid applying the solution or similar liquids directly onto the thermal imager, cables, or other components, to prevent damage to the device.

7.2 Clean the infrared imager lens

Warning:

When cleaning the infrared lens, avoid applying excessive force. This could damage the lens's anti-reflective coating.

Technical Parameter

Contact Information

Mileseey Technology (US) Inc.

Office Add: 17800 CASTLETON ST STE 665 CITY OF INDUSTRY, CA 91748

Manufacturer: Shenzhen Mileseey Technology Co., Ltd.

Add: No.3601 Block A, Tanglang Town Plaza West, Fuguang Community, Taoyuan Street, Nanshan District, Shenzhen, China

Website: www.mileseey.net

Store: www.mileseeytools.com

E-mail: service@mileseey.com

Made in China

MILESEEY has been researching, developing, and manufacturing high-quality optical products, including golf & hunting rangefinders, laser measure devices, and thermal & digital night visions since 2009. With over 12 years of focus on development, research, and manufacturing, Mileseey strives to provide premium-quality products and satisfying customer service to make your life easier and smarter.

Certifications: FC, CE, ROHS, Reach

Recycling Information:

• WEEE Directive: Products marked with the WEEE symbol should not be disposed of as unsorted municipal waste. Return to your local supplier or designated collection points for proper recycling. More information: www.quefairedemesdechets.fr
• Battery Directive: Batteries should not be disposed of as unsorted municipal waste. Return to your supplier or a designated collection point for proper recycling.

FCC Caution

FCC ID: 2AEOG-TP2PLUS

§ 15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Body Operation

This device was tested for typical body operations. To comply with RF exposure requirements, a minimum separation distance of 5mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.