Scosche TAQ04 Qi Center Console Direct Fit Bezel

Parts Included

• (1) Direct Fit Bezel w/ MQUSM
• (1) Vehicle Specific T-harness
• (2) MAGICPLATE™
• (2) MAGICPLATE™ Applicator
• (6) Double-sided Adhesive

Diagram Description: Visual representation of the kit components: a direct fit bezel, a vehicle-specific T-harness, two MAGICPLATE™ units, two MAGICPLATE™ Applicators, and double-sided adhesive strips.

Important Notes & Warnings

WARNING: Do not use the magnetic mount with any hard-drive based devices such as iPod classic, iPod Video, and Zune MP3 players. Use caution when removing or handling plastic parts of any vehicle. Unnecessary force or pressure can cause pieces to crack or break. Please use a plastic card to remove the metal plates. Remove adhesive residue with a non-abrasive cleaner.

CAUTION: This magnetic device is not a toy. The small magnets are harmful if swallowed. Keep away from children.

Preliminary Introduction

Wirelessly charge your Qi-enabled smartphone without the need to plug your device into a car charger or USB cable. This kit offers quick charging at 5W or 10W. The high-powered neodymium magnets are 100% safe and will not damage your device. The TAQ04 is compatible with Qi-enabled smartphones from manufacturers like Apple, Samsung, Google, Microsoft, LG, HTC, and Motorola, as well as Qi-enabled cases, receivers, and battery covers.

Installation Caution

CAUTION: Disconnect your vehicle's negative battery terminal before installation to help prevent electrical damage. It is recommended to use a volt/ohm meter over a test light to check wiring. A test or grounded wire probe can cause damage to the vehicle's computer and/or diagnostic system. Avoid all factory airbag wiring, as airbags can accidentally deploy causing serious injury or death. Refer to your vehicle's instructions for any special tools your installation might require.

Support & Liability

IMPORTANT! DO NOT RETURN PRODUCT TO THE RETAILER. For assistance or replacement parts, contact Scosche at: 1-800-363-4490 X1 | www.scosche.com/contact. Office hours: Mon-Fri: 8AM-5:30PM (PST) and Sat: 8AM-2PM (PST).

Liability Disclaimer: This instruction booklet is based on carefully documented data and research of automobile disassembly, wire harness, and installation information. Scosche Industries, Inc. cannot be held responsible for discrepancies or inconsistencies due to automobile manufacturing changes or options, or damages that may occur during installation.

©2018 SCOSCHE INDUSTRIES, INC. TAQ04 02/19

MAGICPLATE™ Mounting Options

Option 1: For mounting directly to device

Use the large single plate with template guide.

Step 1

Remove the white paper backing from both plates.

Step 2

Line up the corresponding arrows on the Template Guide to the bottom of your phone.

Step 3

When positioned, press plates firmly to affix and remove template.

Diagram Description: Visual guide for Option 1: showing removal of paper backing from a plate, alignment of a template guide on a phone's bottom edge, and firm pressing of the plate onto the phone.

Removing the Plate

Use a thin plastic card to carefully lift the plate's adhesive surface. Slowly lift and remove the plate. Do not use heat or liquids, as this may damage your phone. Contact Scosche Customer Service for assistance at 800.363.4490 Ext. 1 or customerservice@scosche.com.

Option 2: For mounting directly to CASE

Use the (2) small plates with the integrated template guide.

Step 1

Remove the white paper backing from both plates.

Step 2

Line up the corresponding arrows on the Template Guide to the bottom of your phone.

Step 3

When positioned, press plates firmly to affix.

Diagram Description: Visual guide for Option 2: showing removal of paper backing from small plates, alignment of a template guide on a phone case's bottom edge, and firm pressing of the plates onto the case.

Removing the Plate

Use a thin plastic card to carefully lift the plate's adhesive surface. Slowly lift and remove the plate. Do not use heat or liquids, as this may damage your phone. Contact Scosche Customer Service for assistance at 800.363.4490 Ext. 1 or customerservice@scosche.com.

Option 3: For mounting directly to Galaxy S9/S9+ device only

Use the (2) small plates with the integrated template guide for Galaxy.

Step 1

Remove the white paper backing from both plates.

Step 2

Line up the "U" channel to the fingerprint reader and camera on the phone.

Step 3

Remove the backing from the protective film (A) and place it between the device and the lower plate (B). The protective film must be used when applying MAGICPLATE™ directly to the back of the device.

Step 4

When positioned, press plates firmly to affix.

Step 5

Remove template guide.

Diagram Description: Visual guide for Option 3: showing paper backing removal, alignment of a template guide with a "U" channel for fingerprint reader/camera, placement of protective film between device and plate, firm pressing, and removal of the template guide.

Removing the Plate

Use a thin plastic card to carefully lift the plate's adhesive surface. Slowly lift and remove the plate. Do not use heat or liquids, as this may damage your phone. Contact Scosche Customer Service for assistance at 800.363.4490 Ext. 1 or customerservice@scosche.com.

Vehicle Disassembly

Modification Required: Please read complete instructions before proceeding. If you are unsure or find the installation difficult, seek professional installation. Scosche is not responsible for additional installation fees or modifications done by the installer.

Caution! Before beginning disassembly, ensure the following: Negative battery terminal is disconnected. Parking brake is ON. Gear shifter is set to a lower gear.

Accessing 12V Power

Preliminary Steps

1. Disconnect negative battery terminal.

2. Parking brake is ON.

3. Gear shifter is set to a lower gear.

Diagram Description: Illustration of a car's gear shifter console area.

Removing the Shifter Knob

A. Unclip the shifter boot from the knob.

B. Twist to loosen and unscrew the shifter knob.

Diagram Description: Visuals showing how to detach the shifter boot and then unscrew the shifter knob.

Removing Lower Tray

A. Using a panel removal tool, remove the tray panel located below the shifter and cupholders.

B. Remove and retain the (2) screws securing the shifter panel.

Diagram Description: Visuals showing the removal of the lower tray panel and the extraction of its two securing screws.

Removing the Shifter Panel

A. Carefully lift, disconnect, and remove the panel from location. Note: Retain and set aside for re-installation.

Diagram Description: Visual showing the careful lifting and removal of the shifter panel.

Removing the Center Pocket

A. Remove and retain the (2) screws securing the center console pocket.

B. Carefully lift, disconnect, and remove the pocket center console pocket from location.

Diagram Description: Visuals demonstrating the removal of screws and the subsequent lifting and removal of the center console pocket.

Removing the Rubber Mat

A. Open the center console's pocket lid, then remove the mat from location. Note: The mat is not retained for re-installation; keep it safe in case you decide to uninstall the Qi assembly later.

Diagram Description: Visual showing the opening of the console pocket lid and removal of the rubber mat.

Testing Qi Module (MQUSM)

Testing Connection: Before installation, test the module's functionality by connecting the provided vehicle-specific t-harness. Connect the module, place a Qi-enabled device on it, and refer to the LED Status chart. For technical assistance, call 1-800-363-4490 x1 or visit www.scosche.com/contact.

Note: The module can also be tested using a USB to Type-C power source (not included).

Connecting Universal 12V Harness

1. Tap into the vehicle's 12V Power harness using appropriate tools.

2. Color match and clamp connect the Universal power harness to the vehicle's 12V harness.

3. If connected correctly, the module will light up when the vehicle is turned on, and the 12V power socket will retain power.

Diagram Description: Wiring diagram showing connection of 12V power harness (Black to Black Ground, Red to Red Power) to the Qi Module (MQUSM).

Important: Foreign Object Detection

Follow MAGICPLATE™ mounting instructions on pages 2 or 3 for best charging results. Metallic objects blocking the charging coil may prevent the module from working correctly.

LED Charging Status

The LED indicator on the mount shows charging status. When powered ON, it blinks: BLUE, GREEN, BLUE. Standby = Green, Charging = Blue.

Preparation

After confirming the module's working status, retrieve the pocket/shifter panel removed during disassembly. Follow the steps below to ensure correct pocket modification and proper fit of the TAQ04 bezel.

CAUTION! DO NOT attempt to drill a hole while the pocket is still mounted to the vehicle.

Preparation Step A

Place TAQ04 Direct Fit bezel into pocket panel.

Preparation Step B

Use a contrasting chalk or marker, estimate and mark the hole location, then remove the Qi-bezel.

Preparation Step C

Carefully make a hole large enough to pass the USB Type-C connector through.

Diagram Description: Visuals for preparation steps: A) placing the bezel into the pocket, B) marking the hole location, C) drilling a hole for the connector.

Vehicle Assembly

Step 7: Connect Power T-harness

Connect the provided power t-harness according to the diagram. Connect the female and male 12V power connectors first, then route the Type-C connector to the designated slot created during preparation.

Diagram Description: Wiring diagram showing the connection of the power t-harness: Female connector to 12V harness connector, Male connector to back of 12V socket, leading to the Qi Module (MQUSM).

Step 8: Routing the Type-C Connector

A. Pass the Type-C connector through the hole created during preparation on the pocket.

B. Pass the connector through the TAQ04 bezel.

C. Place the direct-Qi bezel into the pocket location.

Diagram Description: Visuals showing the Type-C connector being threaded through the prepared pocket hole and then through the TAQ04 bezel.

Step 9: Routing Type-C to MQUSM Qi Module

A. Connect the Type-C connector to the MQUSM.

B. Place the module onto the Qi bezel.

C. Re-install the pocket into place using screws removed during disassembly.

Notes:

• Hide any excess wiring under the panels/pocket before reassembling.
• Use the provided two-sided adhesives to secure the panel/module from moving.

Diagram Description: Visuals showing the Type-C connector plugged into the MQUSM module, the module seated on the Qi bezel, and the pocket being re-installed with screws.

Step 10: Final Reassembly

Reassemble everything in reverse order. Place your Qi-enabled device onto the TAQ04 assembly to charge. Refer to LED Charging Status (page 5) for charging details.

*Phone NOT included

Diagram Description: Final illustration showing a smartphone placed on the installed Qi charging assembly.

FCC Statement

This equipment has been tested and found to comply with the limits for a WPC device, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the product.

NOTE: This equipment has been tested and found to comply with the limits for a wireless power charger, pursuant to Part 18 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If interference occurs, try to correct it by reorienting/relocating the receiving antenna, increasing separation between equipment and receiver, or connecting to a different circuit. Consult a dealer or technician if needed.

FCC Statement (Canada)

This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. This equipment complies with IC RSS-102 radiation exposure limits for an uncontrolled environment. This transmitter must not be co-located or operated with any other antenna or transmitter.

Warranty and Contact Information

For complete warranty details or questions, visit www.scosche.com or contact us at: www.scosche.com/contact, customerservice@scosche.com, 1(800) 363-4490 ext.1.