Scosche MagicMount Charge Elite User Guide

Included Elements

• A. MagicMount™ Charge Elite Magnetic Wireless Charging Mount with Integrated Cable Management System
• B. Rotating Mounting Arm
• C. Adhesive Dash Mount
• D. Locking Vent Mount
• E. Mounting Arm Removal Tool
• F. Car Adapter
• G. Replacement Adhesive for Dash Mount
• H. Cable Clips (2)
• I. Cleaning Wipe

Device Setup

This guide covers setup for various mounting options:

• Section A: iPhone® Setup
• Section B: Adhesive Dash Mount Installation
• Section C: Monitor Mount Installation
• Section D: Vent Mount Installation
• Section E: Integrated Cable Management System
• Section F: Connection & Charging Specifications
• Section G: Charging Head Adjustment

Section A: iPhone® Setup

With Case: For iPhone 12 and later, cases must include embedded magnets designed to work with MagSafe™ accessories for secure attachment.

Without Case: iPhone 12 and later without a case can be directly attached to the MagicMount Charge Elite.

Section B: Adhesive Dash Mount

Installation Steps:

1. Thoroughly clean the desired mounting surface using the provided cleaning wipe.
2. Firmly bend Flex Tabs before attaching to a curved surface.
3. Peel off the protective backing and attach the mount to the desired surface.
4. For best adhesion, firmly hold the mount against the dash for 30-60 seconds. Ultimate bond strength is achieved after 24 hours.

Note: The cleaning wipe may cause discoloration on certain plastics, vinyls, and painted surfaces. It is recommended to test in an inconspicuous area first.

Section C: Monitor Mount

To attach the mount to a monitor:

1. Use the included tool to remove and reverse the adhesive mounting base. Ensure the adhesive side faces the same direction as the phone mount and the monitor screen [Diagram A].
2. Follow the steps to attach the adhesive base to the rear of the monitor [Diagram B].

Section D: Vent Mount

To attach the mount to a vehicle vent:

1. Remove the mounting arm from the adhesive mount [Diagram A] and assemble it with the vent mount [Diagram B].
2. Tighten the collar to close the vent clips, lock the support skirt, and secure the mount onto the vent [Diagram C]. Loosen the collar to open the vent clips [Diagram D].
3. Note: Loosening the collar also unlocks the support skirt, allowing it to rotate in relation to the vent clips [Diagram E]. This enables installation on different vent styles (horizontal, vertical, angled) while the support skirt is positioned independently. For maximum support, it is recommended to install the support skirt upright (vertically).
4. With the vent clips open and positioned correctly, place them on the vent and tighten the collar to secure the mount [Diagram F].

Note: This mount works with many vent designs [Diagram G]. It is not compatible with curved or circular vents [Diagram H].

Section E: Integrated Cable Management System

Manage your charging cable length:

1. Release the cable from the output slot [Diagram A].
2. Manually unwind the cable from the internal storage reel [Diagram B], or wind the cable onto the storage reel [Diagram C] to adjust the exposed cable length.
3. Once the desired length is set, replace the cable in the output slot [Diagram D].

Note: Minimum cable length is 1 ft (30 cm); maximum length is 4 ft (1.2 m).

Section F: Connection & Charging Specifications

Qi2 Wireless Charging Head:

• Input (USB-C PD): 5V-3A / 9V-2.22A
• Output: 15W / 10W / 7.5W / 5W

Note: Actual charge rates may vary depending on device software and environmental conditions.

Car Adapter:

• Input: 12V-24V-7A
• Output (USB-C): 5V-3A / 9V-2.22A

Section G: Mount Adjustment

Adjust the mount for optimal positioning:

• The dual ball-joint design allows the charge head to tilt and rotate [Diagram A].
• The charge head slides along the mounting arm to adjust its reach [Diagram B].
• The mounting arm can be rotated by loosening the collar at the mounting base [Diagram C].