Scosche MagicMount PRO CHARGE

Section A: iPhone 12 or Later (with optional MagSafe™ Case)

For iPhone 12 or later models using a MagSafe-compatible case, the MagicMount PRO CHARGE can attach directly. The MagSafe case is required for proper function. The MagicPlate is not needed in this configuration.

For iPhone 12 or later models without a case, the MagicPlate is also not required.

Section B: Wireless Charging Smartphones (with Case)

For other Qi-compatible smartphones (e.g., iPhone 11, Pixel 4 and newer) that require a case for wireless charging:

Use the included template (I) to position the MagicPlate (E) correctly on the back of the device's case. Ensure the plate is centered for optimal charging. Note: Manufacturing materials of some cases may prevent direct adhesive bonding.

Section C: Attaching Device with MagicPlate

For Qi-compatible smartphones without a case, or for devices that do not have a built-in MagSafe or Qi charging system:

1. Clean the device surface with the supplied wipe (H).

2. Apply the Protective Film (F) to the device surface where the MagicPlate will be placed. This film helps with easier removal later.

3. Use the Mounting Template (I) to accurately position the MagicPlate (E) onto the Protective Film. Press firmly to adhere.

Note on MagicPlate Removal: If the MagicPlate needs to be removed, use a credit card to gently slide between the film and the plate. Avoid using sharp or hard objects, as they can damage the device.

Section D: Window/Dash Mount

Window Mount:

1. Clean the window surface thoroughly.

2. With the lever in the UP position, place the mount arm onto the window. Press the lever down to securely lock it in place.

StickGrip Dash Mount:

1. Select a flat surface on the dashboard and clean it using the supplied wipe (H). Test the wipe in an inconspicuous area first, as it may cause discoloration on some plastic, vinyl, or painted surfaces.

2. Remove the protective film from the StickGrip mounting base (G). Place the base onto the prepared surface and press firmly.

3. With the lever in the UP position, place the mount arm onto the StickGrip base and press the lever down to lock it in place.

Note on StickGrip: StickGrip may leave residue or discoloration on some surfaces. It might also leave a ring mark when mounted on a dashboard. To renew and reuse the StickGrip base, rinse it under warm water and allow it to air dry.

Section E: Mount Adjustment

Charge Mount Adjustment: Loosen the ball-joint collar to adjust the viewing angle or rotate the mount 360°.

Telescoping Arm Adjustment: Loosen the front knob to extend the telescoping arm. Loosen the rear knob to adjust the angle of the arm.

Section F: Connection & Charging

LED Indicators:

• Blue: Charging
• Flashing Red: Foreign Object Detected (FOD)

Wireless Charging Head Specifications:

• Input: 12V-2A
• Output: 15W / 10W / 7.5W / 5W
• *Actual charge rates may vary based on device software and environmental conditions.

Car Charger Specifications:

• Input: 12V-24V-6A
• Output (Type-C): 5V-3A / 9V-2.22A (20W USB-C Power Delivery Port)
• Output (DC): 12V-2A

Connect the charging cable from the MagicMount PRO CHARGE head to the Car Charger, and plug the Car Charger into the vehicle's power outlet.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body.

Canadian Compliance Statement

This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3 (B)/NMB-3(B)

CE Declaration of Conformity

Scosche Industries Inc. declares that the product type MPQ4 is in compliance with Directives 2014/53/EU. The full text of the EU declaration of conformity is available at: www.scosche.com

This equipment should be installed and operated with a minimum distance of 10 cm between the device & your body.

Frequency Bands: 111~148KHz.

Maximum radio-frequency power: The maximum power for all bands is less than the highest limit value specified in the related Harmonized Standard. Nominal limits applicable to this radio equipment are:

• 29.31 dBuA/m at 3m
• SAR 6.176 V/m at 10 cm distance

Max operation temperature: 25℃