NOMA Portable Air Conditioner Window Kit
Instruction manual for household use only
Model No. 043-2729-4 | Contact us 1-866-827-4985
Parts Package
Before beginning, check that all parts are included in the parts package.
- Non-adhesive foam seal
- Adhesive foam seal (2)
- Adhesive foam seal (2)
- Flexible exhaust hose
- Window exhaust adaptor
- Coupling
- Panel H
- Panel I
- Panel J
- Panel K
- Window-lock bracket (2)
- Inner slider section-short
- Inner slider section
- Outer slider section with vent
- Outer slider section
- Rivets (4)
- Wood screws (4)
Tools needed
- Cross-head screwdriver
- Pencil
- Scissors
Step 1: Suitable Windows
The window installation kit allows you to install the air conditioner in most vertical-sliding windows 18 to 50" (45.7 to 127 cm) wide, or horizontal-sliding windows from 18 to 50" (45.7 to 127 cm) high.
Choose the right panel:
| Window Width/Height | Panel H: 18" (45.7 cm) | Panel I: 9 11/16" (24.6 cm) | Panel J: 18" (45.7 cm) | Panel K: 18" (45.7 cm) |
|---|---|---|---|---|
| 18" (45.7 cm) | V | |||
| 19 to 26" (48.3 to 66 cm) | V | V | ||
| 27 to 34" (68.6 to 86.4 cm) | V | V | V | |
| 35 to 50" (88.9 to 127 cm) | V | V | V | V |
Step 2: Window Installation
- Cut the adhesive foam seal to the proper length, and attach it to the window sash and frame.
- Insert the vent panel assembly, including extension panels, if needed, into the window opening. Extend the extension panels, if used. If your window length requires more than two panels, after adjusting the length, please secure the panels with rivets.
- Cut the non-adhesive foam seal to the window width. Stuff the foam seal between the glass and the window to prevent air and insects from getting into the room.
- Install the window-lock bracket with wood screws as shown, if you need.
Step 3: Connect it together
- Preparing the exhaust hose assembly: Press the flexible exhaust hose into the coupling and the window exhaust adaptor. Both the coupling and window exhaust adaptor have integral clips that snap onto the hose.
- Connect The Hose To The Air Conditioner: Slide the coupling into the slot on the back of the air conditioner to lock the hose on the unit.
- Connect The Hose To The Window: Roll the air conditioner to selected location. Attach the window exhaust adaptor to the outer slider section (the piece with the large exhaust hole). Pull evenly on the folds to extend the end of the flexible vent hose. Attach the portable air conditioner original coupling to flexible exhaust hose. Turn counter-clockwise until securely into place.
For other brands that use 5.9" diameter hoses:
If included coupling doesn't match your portable air conditioner outlet, remove the Noma® coupling and connect the hose to the original portable air conditioner coupling. If the original portable air conditioner's coupling requires it to be attached by screwing it onto the hose, the plastic ring on the coupling side must be removed first. To remove the plastic ring, turn it clockwise until it comes off.
Step 4: Plug In the Unit
Be sure to use a grounded 3 prong outlet. Do not use an extension cord. Plug in the unit.
Step 5: Turn The Unit On
Turn the air conditioner on, and set the desired mode and temperature.
Important Notes and Warnings
CAUTION:
- For household use only.
- Keep out of the hands of small children.
To ensure proper ventilation, keep a distance of at least 20" (50 cm) between the Portable AC and the window.
This Noma product carries a 90 Days warranty against defects in workmanship and materials. Noma Canada agrees to replace a defective product, within the stated warranty period, when returned to the place of purchase with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.
MADE IN CHINA
Imported by Noma Canada, Toronto, Canada M4S 2B8
