Westfalia 8V Mini Drill and Grinder

Introduction

Welcome to your new Westfalia 8V Mini Drill and Grinder. This manual provides essential operating instructions, technical specifications, and safety guidelines to ensure safe and effective use of your tool. Please read this document carefully and keep it for future reference. If you transfer ownership of the device, include this manual.

Product Overview

The 8V Mini Drill and Grinder is designed for various drilling and grinding tasks. Key components include:

• 1. Clamping Chuck: The part that securely holds the tool bit in place.
• 2. LED Light: Integrated light to illuminate the work area for better visibility.
• 3. Spindle Lock: A mechanism to lock the spindle, facilitating the easy and secure insertion or removal of tool bits.
• 4. On/Off Switch: The primary control for powering the device on and off.
• 5. Speed Regulator: Allows adjustment of the tool's rotational speed to suit different materials and tasks.
• 6. Battery Charge Indicator: A visual display (e.g., LEDs or bars) showing the current battery charge level.
• 7. USB-C Charging Socket: Port for recharging the internal battery.

Operating Instructions

1. Unboxing and Initial Setup

   Carefully unpack the device and all accessories. Dispose of packaging materials responsibly, ensuring they are kept out of reach of children ?? to prevent any suffocation hazards.

2. Charging the Battery

   Connect the provided USB-C cable to the charging socket (7) on the tool and to a suitable USB power source. The battery charge indicator (6) will display the charging status. For optimal battery health, charge the device within a temperature range of +10°C to +40°C ?️.

3. Inserting a Tool Bit

   Loosen the clamping chuck (1) by turning it. Insert the desired tool bit fully into the chuck. Tighten the clamping chuck securely. For extra security, engage the spindle lock (3) while tightening.

4. Powering On the Device

   Press the On/Off switch (4) to turn the tool on. Ensure the tool bit is clear of the workpiece before activation ▶️.

5. Adjusting Speed

   Use the speed regulator (5) to select the appropriate speed for your specific application. Adjust the speed as needed during operation for optimal control and results.

6. Monitoring Battery Level

   Refer to the battery charge indicator (6) to monitor the remaining battery power and plan your work accordingly.

Technical Specifications

The declared vibration total value and noise emission values are measured according to standard test methods and can be used for comparison between tools or for preliminary exposure assessment.

Safety Instructions

General Warnings:

• ⚠️ Read all safety instructions and this manual carefully before use.
• ⛑️ Always wear appropriate personal protective equipment, including safety goggles and hearing protection.
• If the device causes discomfort or irritation, stop work immediately and investigate the cause.
• ?? Dispose of unnecessary packaging material responsibly, keeping it out of reach of children to prevent suffocation hazards.
• ? Individuals with limited physical, sensory, or mental capabilities should only use the device under supervision and instruction.
• ⚡️?? Use metal and voltage detectors to locate hidden power, water, and gas lines. Do not touch live components or conductors.
• ? Ensure the work area is adequately lit.
• Ensure the tool bit is securely fastened in the clamping chuck. Loose bits can be ejected and cause injury.
• Place the tool on the workpiece before switching it on.
• Check for sufficient clearance under the workpiece for the tool bit.
• Do not apply excessive pressure; this shortens the device's lifespan.
• ? Tool bits can become very hot during operation. Risk of burns. Allow bits to cool before touching.
• Never use your hands to remove chips or debris near the tool bit.
• If interrupted, complete the current step and turn off the device before looking away.
• Use clamps or a vise to secure the workpiece whenever possible.
• Regularly inspect the clamping chuck for wear and damage. Have defective parts repaired by an authorized workshop.
• Always wait for the tool bit to come to a complete stop before setting the device down.
• Periodically check all screws, nuts, and fasteners for tightness and tighten if necessary.
• Have repairs performed only by qualified specialists using original spare parts.
• Allow the device to cool down for 15 minutes after charging or intensive use to prevent overheating or fire.
• Do not open, disassemble, compress, heat above 60°C, or incinerate the device. Do not throw into fire or similar.
• ? Be cautious when using near flammable or easily meltable materials (e.g., plastic, glass).
• Do not aim the device at the same spot for extended periods.
• Never point the switched-on device at people, animals, plants, flammable objects, or liquids.
• ? Do not use in explosive atmospheres.
• Be aware that heat can conduct to obscured combustible materials.
• Keep air vents clean to prevent overheating and fire risk.
• Use only original accessories.
• If the device is damaged, stop use and contact customer service for repair. Do not attempt self-repair.

Battery Safety Warnings:

• ?⚠️ Lithium-ion batteries pose a fire, burn, and explosion hazard if misused, stored, or charged improperly.
• ♻️?️❌ Cordless devices and their batteries do not belong in household waste. Dispose of them properly according to local regulations.

EC Declaration of Conformity

Westfalia Werkzeugcompany declares that the 8 V Akku Mini-Bohr-Fräswerkzeug (Art. No. 99 20 18) complies with essential safety requirements of relevant European Directives, including RoHS, EMC, and Machinery directives.

The technical documentation is on file at the QA department of Westfalia Werkzeugcompany.

Hagen, 17th of July, 2023

Thomas Klingbeil, Quality Assurance Representative

Customer Support and Disposal

Customer Services

Germany: Westfalia, Werkzeugstraße 1, D-58093 Hagen. Tel: (0180) 5 30 31 32, Fax: (0180) 5 30 31 30, Internet: www.westfalia.de

Austria: Westfalia, Moosham 31, A-4943 Geinberg OÖ. Tel: (07723) 4 27 59 54, Fax: (07723) 4 27 59 23, Internet: www.westfalia-versand.at

Switzerland: Westfalia, Wydenhof 3a, CH-3422 Kirchberg (BE). Tel: (034) 4 13 80 00, Fax: (034) 4 13 80 01, Internet: www.westfalia-versand.ch

Disposal Information

Please help avoid waste. This article contains valuable materials that can be recycled. Do not dispose of it in household waste. Take it to your local collection point for electrical and electronic equipment.

♻️ Cordless devices and batteries must be disposed of properly together with the devices.