MOMAN H2S Helmet Intercom User Manual

Caring For the MOMAN Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping or the impact of external force.
• Do not attempt to disassemble the product. Doing so voids the warranty.
• Please have the product checked or repaired by authorized technicians if any malfunctions happen.
• Failure to follow all the instructions may result in mechanical damage.
• Warranty does not apply to human errors.

Product Instruction

Power On: Long press the on/off button for 3 seconds. Wait for the blue indicator to flash slowly. Voice Prompt: Power On, Bluetooth Mode On.

Power Off: Long press the on/off button for 3 seconds. The red indicator stays on for 2 seconds then turns off. Voice Prompt: Power Off.

Note: Will automatically turn off when not in use for 10 minutes.

Operation

1. Mobile Pairing

   For the first-time use, the blue indicator flashes and the H2S enters Bluetooth mode. Voice Prompt: Bluetooth Mode On.

   Enable Bluetooth on your phone and connect to "H2S". The blue indicator stays on after the pairing is successful. Voice Prompt: Bluetooth Connected.

   Note: The H2S automatically connects to previously connected and remembered devices. You can connect 2 phones simultaneously. To connect the second phone, disconnect from the first and connect the H2S on the second phone, then re-enable Bluetooth on the first phone to reconnect.

2. Intercom Pairing

   1. Pairing: Short press the intercom button on ONE H2S to enter intercom mode (Red and blue lights flash quickly) and search for nearby H2S. Wait 2 seconds to enter pairing mode, and the red and blue lights will flash quickly. Once paired, the blue lights on both H2S will stay on. Voice Prompt: Intercom Mode On, Intercom Pairing.
   2. Exit Intercom Mode: Long press the intercom button for 3 seconds to exit intercom mode. Voice Prompt: Intercom Mode Off.
   3. Unpairing: After exiting intercom mode, quickly double-press the intercom button on both paired H2S to unpair. (Red and blue lights flash quickly.) Voice Prompt: Bluetooth Mode On, Retry. Note: Unpairing will not be successful if only one H2S is unpaired.
   4. Auto Reconnect: If the connection is lost due to distance or signal interference, it will enter the auto-reconnect mode. Voice Prompt: Intercom Pairing Succeed. Note: If reconnection fails after 5 minutes, the device will deem it failed. Please short press the intercom button to retry searching for nearby devices.
   5. Volume Adjustment: Increase Volume: Quickly rotate the knob counterclockwise twice. Decrease Volume: Quickly rotate the knob clockwise twice.

3. Music Sharing Pairing

   1. Pairing: After intercom pairing is successful, press the on/off button to enter music sharing mode (red and blue lights flash slowly). Wait 2 seconds for pairing (red and blue lights flash quickly). Once paired, blue lights stay on. Voice Prompt: Music Sharing Pairing, Music Sharing Pairing Succeed. Note: If pairing fails, press the music sharing button to retry. (If no connection is established within 5 minutes, it is considered a failure.)
   2. Exit Music Sharing Mode: Short press the power button to exit music sharing mode. Voice Prompt: Music Sharing Off.
   3. Auto Reconnect: If the connection is lost due to distance or signal interference, it will enter the auto-reconnect mode. Voice Prompt: Music Sharing Pairing Succeed. Note: If reconnection fails after 5 minutes, the device will deem it failed and enter the intercom mode automatically. Please short press the intercom button to retry searching for nearby devices.
   4. Volume Adjustment: For Music Sharing Transmitting Device: Increase Volume: Turn the knob counterclockwise and hold. Decrease Volume: Turn the knob clockwise and hold. For Music Sharing Receiver Device: Increase Volume: Quickly turn the knob counterclockwise twice. Decrease Volume: Quickly turn the knob clockwise twice.

4. Switch Between Intercom Mode and Music Sharing Mode

   In music sharing mode, short press the intercom button to switch to intercom mode.

   In intercom mode, short press the on/off button to switch to music sharing mode.

   Short press the intercom button Music Sharing Mode

   Short press the on/off button Intercom Mode

5. Voice Assistant

   Connect the Bluetooth then long press the FM button for 2s to activate/deactivate the voice assistant.

6. Phone Settings

   Disconnect the Bluetooth connection, long press the FM button and turn the knob counterclockwise simultaneously. Release after hearing "Auto Answer/Manual Answer" to switch between manual and auto answer modes. The H2S is set to the Auto Answer mode by default.

   • Auto Answer Mode: The call will be automatically answered after 10 seconds. Long press the FM button for 2 seconds to reject the call.
   • Manual Answer Mode: Short press the power button briefly to answer/end the call. Long press the FM button for 2 seconds to reject the call.
   • Last Number Redial: Double press the power button quickly to redial the last call.

7. Music Settings

   • Pause/Play: Short press the FM button briefly to pause/play music.
   • Next Song: Turn the knob clockwise quickly.
   • Previous Song: Turn the knob counterclockwise quickly.
   • Increase Volume: Turn the knob counterclockwise and hold to increase volume (*Bass Effect: Max.Volume).
   • Decrease Volume: Turn the knob clockwise and hold to decrease volume.

8. FM Radio

   • Enter/Exit FM Mode: Double press the FM button. Voice Prompt: FM Radio On.
   • Search Stations: Short press the FM button to start/stop searching for FM stations.
   • Next Station: Turn the knob clockwise quickly to switch to the next station.
   • Previous Station: Turn the knob counterclockwise quickly to switch to the previous station.
   • Increase Volume: Turn the knob counterclockwise and hold to increase volume (*Bass Effect: Max.Volume).
   • Decrease Volume: Turn the knob clockwise and hold to decrease volume.

   Note: Radio Station: 76-108MHz. Will store the stations automatically. Will delete the saved stations if re-scanning.

9. Audio Mixing Function

   The dual-chip design of the H2S supports simultaneous intercom and Bluetooth operation, allowing you to listen to intercom + music/navigation/FM/voice assistant. During intercom calls, music/FM/navigation/voice assistant volume will automatically decrease and return to normal after the call ends.

10. Language Settings

    Disconnect the Bluetooth, long press the power button and turn the knob clockwise. Release after hearing "English/Japanese" to switch between English and Japanese.

11. Restore Factory Settings

    Power it on and disconnect the Bluetooth, long press the FM button for 8 seconds to restore factory settings. Pairing memory will be eliminated. During reset, the red and blue lights stay on, then turn off after release, and the device shuts down automatically.

12. Charging

    Red light flashes and voice prompt "low battery, please charge" when the battery is low, please charge via Type-C charging cable. Red Light on when charging. Light off when fully charged. Charging Voltage: 5V-0.5A.

Installation

Method 1: Using the Back Clip (Insert Style)

1. Loosen the screws on the clip and separate the front and back parts.
2. Open the helmet padding and insert the clip into the rear edge of the helmet (as shown), then close the clip and tighten the screws.
3. Slide the microphone headset into the clip slot and lock it securely.
4. Open the helmet padding at the ear position, clean the EPS surface, and stick the adhesive tape on both sides of the helmet.
5. Attach the speakers to the adhesive tape, with the shorter speaker cable placed near the microphone. Secure the speakers and tidy up the helmet padding and cables.
6. Plug the headset cable into the microphone port, organize the wires, and secure them inside the helmet.

Installation Method 2: Back Clip (Stick Style)

1. Loosen the screws on the clip and separate the front and back parts.
2. Apply the adhesive to the back of the clip and stick it to the side of the helmet.
3. Slide the microphone headset into the clip slot and lock it securely.
4. Open the helmet padding at the ear position, clean the EPS surface, and apply the adhesive tape to both sides of the helmet.
5. Attach the speakers to the adhesive tape, with the shorter speaker cable placed near the microphone. Secure the speakers and organize the helmet padding and wires.
6. Plug the headset cable into the microphone port, organize the wires, and secure them inside the helmet.

Removal

1. Remove the microphone cable.
2. Press the inner clip bar in the center of the clip with one finger. Slide the microphone out of the clip.
3. For the removal of the speakers and clip, refer to the installation instructions.

Packing List

1-Intercom-Kit

• H2S Wireless Helmet Intercom x1
• Changeable Hard Mic and Soft Mic x1
• Double-Sided Tape x1
• Back Clip(Insert Style) x2
• Back Clip(Stick Style) x1
• Tape Kit (Speaker x4/Hard Mic x2/Soft Mic x2) x1
• Type-C Charging Cable x1
• Interchangeable Pattern Shells Kit (Yellow/Blue) x1
• Hexagon Key x1
• User Manual x1

2-Intercom-Kit

• H2S Wireless Helmet Intercom x2
• Changeable Hard Mic and Soft Mic x2
• Double-Sided Tape x2
• Back Clip(Insert Style) x2
• Back Clip(Stick Style) x2
• Tape Kit (Speaker x4/Hard Mic x2/Soft Mic x2) x2
• Type-C Charging Cable x2
• Interchangeable Pattern Shells Kit (Yellow/Blue) x2
• Hexagon Key x2
• User Manual x1

Specifications

• Connection Distance with Mobile: 10m
• Wireless Version: 5.1 & 5.3
• Wireless Protocol: A2DP, AVRCP
• Charging Port: Type-C
• Battery: 800mAh
• Charging Time: 1.5H
• Charging Voltage: 5V
• Speaker Diameter: 40mm
• Frequency Range: 2.4GHZ
• Temperature Range: -20~50°C

Instruction Warning

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits apply to a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. and (2) This device must accept any interference received, including interference that may cause undesired operation.

Important Notice

• Do not put the product into the fire to avoid explosion.
• Do not dismantle the product to avoid damage.
• Keep the product away from sharp objects to avoid damage.
• If not used for a long time, keep the product in a dry place.