Manuals+

MOMAN H2 PRO

Headset Helmet Intercom

Welcome

Thank you for choosing MOMAN product. Please read this manual carefully before use and follow all instructions mentioned herein.

Caring for Your Moman Product

  • Keep the product in a dry, clean, and dust-free environment.
  • Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage.
  • Use only a soft, dry cloth to clean the product.
  • Malfunction may be due to a fall or impact from an external force.
  • Do not attempt to disassemble the product. Doing so voids the warranty.
  • Have authorized technicians inspect or repair the product if any malfunction occurs.
  • Failure to follow all instructions may cause mechanical damage.
  • The warranty does not apply to human error.

Package List

  • Intercomunicador x2 (x1 for 1-Rider Kit) [Image: Line drawing of the intercom unit.]
  • Clips de velcro x2 (x1 for 1-Rider Kit) [Image: Line drawing of two velcro clips.]
  • Clip Trasero x2 (x1 for 1-Rider Kit) [Image: Line drawing of a rear mounting clip.]
  • Sujetadores de gancho y bucle x2 (x1 for 1-Rider Kit) [Image: Line drawing of hook and loop fasteners.]
  • Altavoces de mic duro y mic suave reemplazables x2 (x1 for 1-Rider Kit) [Image: Line drawing of microphone and speaker components.]
  • Manual x1 [Image: Line drawing of a booklet.]
  • Cable USB x2 (x1 for 1-Rider Kit) [Image: Line drawing of a USB cable.]
  • Destornillador x2 (x1 for 1-Rider Kit) [Image: Line drawing of a small screwdriver.]
  • Velcro para auriculares x8 (x4 for 1-Rider Kit) [Image: Line drawing of circular velcro pads.]

Product Introduction

[Diagram: Line drawing of the intercom unit with numbered callouts pointing to specific parts: 1. On/Off Button, 2. Indicator Light, 3. Function Button, 4. Charging Port, 5. Rotary Button, 6. Headphone Interface, 7. Buckle Flap, 8. Speaker, 9. Headphone Jack, 10. Microphone Adapter, 11. Replaceable Hard Microphone, 12. Replaceable Soft Microphone.]

Important Notice: Before installing the headphones, follow the Quick Start Guide instructions to connect your phone and adjust sound and volume. If there is a significant difference in sound effect and volume after installing in the helmet, adjust the speaker position in the helmet.

Operation

1. Power On/Off

Powering ON: Press the On/Off button for 2 seconds.

Powering OFF: Press and hold the ON/OFF button for 4 seconds.

Restart: In power-on mode, press and hold the ON/OFF button for 8 seconds.

LED Indicators:

  • POWERING ON: Blue light flashes twice, then RED and BLUE lights flash alternately. [Diagram: Line drawing of the intercom unit showing flashing blue and red lights.]
  • Voice Prompt: "Di"
  • POWERING OFF: Red light flashes once. [Diagram: Line drawing of the intercom unit showing flashing red light.]

2. Phone Control

Incoming Call:

  • Manual Answer: Briefly press the Function button. ?
  • Auto Answer: No operation after 8 seconds. ?
  • Reject Call: Press and hold the Function button for 3 seconds. ?

End Call: Briefly press the Function button. ?

Redial Last Call: With Bluetooth disconnected, double-click the On/Off button. ?

Auto-answer Mode:

  • Without Bluetooth connection: Double-click the On/Off button.
  • Auto-answer ON: Blue light flashes twice. ?
  • Auto-answer OFF: Red light flashes twice. ?

3. Music Control

  • Play/Pause: With Bluetooth connected, briefly press the Function button once. ▶️⏸️
  • Previous Song: Turn the rotary knob counter-clockwise. ⏪
  • Next Song: Turn the rotary knob clockwise. ⏩
  • Volume Up: Turn the rotary knob counter-clockwise and then HOLD. ➕
  • Volume Down: Turn the rotary knob clockwise and then HOLD. ➖
Note: There is a voice alarm for excessively high and low volume.

4. FM Radio

  • ON: In standby mode, double-click the Function button twice. ?
  • OFF: Double-click the Function button. ?
  • Select Channels: Quickly turn and release the rotary knob to select and adjust. ?
Notes: If the signal is weak indoors, try turning on the FM radio near a window or in an open area. When there is a phone call, the FM radio will be automatically cut off. It resumes when the call ends.

5. Language Change

Turn on, press the ON/OFF button and the rotary button simultaneously. (English → Japanese → Italian) ?

6. Voice Assistant

With Bluetooth connected, press the Function button for 1 second. Voice prompt: "Di". ?

7. Pairing and Disconnection

7.1 With Mobile Phone

  • After powering on, press the ON/OFF and Function buttons simultaneously for 4 seconds. The BLUE light flashes twice, then the RED and BLUE lights flash alternately.
  • Pairing: Activate Bluetooth function, search for "MOMAN H2 PRO" to connect.
  • Voice Prompt: "Bluetooth connected". ? [Diagram: Line drawing of the intercom unit showing connection status.]

7.2 Pairing Two Intercoms

  • After powering on, press the ON/OFF and Function buttons simultaneously for 4 seconds. The BLUE light flashes twice, then the RED and BLUE lights flash alternately.
  • Press the ON/OFF button of one intercom; the BLUE light flashes rapidly. [Diagram: Line drawing of two intercom units.]
  • Voice Prompt: "Intercom Search". ?
  • Voice Prompt: "Bluetooth connected". ?
  • Two intercoms are paired correctly and the BLUE light flashes slowly. [Diagram: Line drawing of two paired intercom units.]
Note: Automatic connection: once the intercoms are paired correctly, they do not need to be paired repeatedly.

7.3 Reconnect and Disconnect

  • Reconnect: Briefly press the ON/OFF key. Voice prompt: "Di". ?
  • Disconnect: Briefly press the ON/OFF key. Voice prompt: "Di". ❌
Notes: Within five minutes of disconnection, it connects automatically; after more than five minutes, briefly press the ON/OFF key to search.

8. Music Sharing

(1) POWERING ON:

  1. After connecting Intercom A to Bluetooth, pair Intercom A with Intercom B.
  2. Disconnect Intercom A and Intercom B.
  3. Intercom A plays music.
  4. Press and hold the Function button of Intercom A. After hearing the voice prompt "Di", continue pressing the Function button for 2 seconds. Music sharing is performed correctly when you hear a voice prompt. [Diagrams illustrating the music sharing process between two intercom units.]

(2) POWERING OFF: Press the Function button of Intercom A for 2 seconds. [Diagram: Line drawing of the intercom unit.]

Note:

  • Music can only be shared from the primary device. The auxiliary device cannot share music. (Statement: If Intercom A and Intercom B are paired, the one that actively pairs is the primary device).
  • Only after resetting factory settings and re-pairing can the primary and auxiliary devices be switched.

If Intercom A's music is paused and Intercom B's music is playing, Intercom A will play Intercom B's music.

9. Multi-mode Switch

① Between Intercom and Music/FM Radio: In Intercom mode, briefly press the ON/OFF button. Voice prompt: "Di". Exit Intercom mode and enter Music/Radio FM mode. [Diagram: Line drawing of the intercom unit with arrows indicating mode switching.]

② Between Intercom and Mobile Phone: [Flowchart: Illustrating call handling sequence: In Intercom mode -> Incoming Call -> Exit call answering mode -> Call ends -> Automatically enter Intercom mode in 5 seconds. ?]

10. Function Priority

  • Level 1: Mobile Phone
  • Level 2: Intercom
  • Level 3: Music/Radio FM

Installation

1. Method 1: Install with Rear Clip

  • Use the screwdriver to loosen the screws of the rear clip so it can be opened to the appropriate extent.
  • Open the inner lining of the helmet, insert the rear clip in the correct position on the left side of the helmet, and tighten the screw.
  • Slide the intercom into the rear mounting slot to secure it.
  • Open the helmet liner (ear area) and clean the helmet surface. Place a velcro strap on the left and right sides of the helmet.
  • Attach the speaker to the velcro surface, and the speaker with the short cord should be placed near the device. Attach the microphone, then the helmet liner and cable.
  • Connect the headphones to the intercom jack and firmly secure the headphone cable.
[Series of diagrams illustrating the steps for installing the intercom onto a helmet using the rear clip method.]

2. Method 2: Installation with Velcro

Disconnect the hook and loop fasteners. First, attach the hook to the velcro clip. Then select the appropriate fixing point on the helmet and fix the intercom to the velcro clip. For installing the speakers, please refer to the previous description. [Series of diagrams illustrating the steps for installing the intercom onto a helmet using the velcro method.]

3. How to Remove the Intercom from the Helmet

First unplug the headphone, then press the fixed buckle in the middle of the rear clip with a finger (push towards the helmet side), so that the hook of the rear clip separates from the intercom, and push the intercom upwards to slide it out of the rear clip smoothly to complete the disassembly. [Series of diagrams illustrating how to remove the intercom from the helmet clip.]

4. How to Attach the Headphone Jack (if necessary)

Unscrew the screws on the back of the intercom with a screwdriver, open the buckle flap, plug in the headphone connector, and tighten the screws. If you need to disconnect the headphones, open the buckle flap by unscrewing the screws. [Diagram illustrating the attachment of the headphone jack.]

Charging Notes

  • Before using the Bluetooth intercom, use the attached charging cable to charge the intercom. The small Type-C interface on the charging line connects to the charging port of the Bluetooth intercom, and the large USB connector on the charging cable connects to the power supply interface for power supply: A. Computer USB interface; B. A mobile power supply with DC 5V output; C. A USB power adapter with DC 5V output.
  • During charging, the red LED is always on. When fully charged, the red light slowly turns off. It takes up to 2.5 hours to fully charge the unit.
[Diagram: Line drawing showing the USB Type-C charging port on the intercom and the USB cable connection to a power source.]

Specifications

SpecificationValue
Transmission Rangeup to 1000 m
Connection Distance with Mobile20m
Bluetooth Version5.1
Bluetooth ProtocolA2DP, AVRCP
Charging PortType-C
Standby Time300H
Working Time20H
Battery900mAh
Charging Time2H
Charging Voltage5V
Speaker Diameter40 mm
Frequency Range2.4 GHz
Temperature Range-20 ℃ ~ 50 ℃

Notes

  • If you do not use the intercom for one month or more, charge it once every two months to protect the lithium battery.
  • The storage temperature of this product is -20 ℃ to 50 ℃, and do not store it in an environment with excessively high or low temperatures, otherwise, the product's lifespan will be affected. ⚠️
  • Do not expose this product to fire to avoid explosions. ⚠️
  • Only two screws on the rear of the intercom can be opened. Do not open other screws on the intercom to avoid short circuits on the main board or damage to the battery.

Contact Information

Moman (UK) Limited
? Unit 25 Basepoint Business Centre, Aviation Park, West Christchurch, United Kingdom BH23 6NX
✉️ www.momanx.com
Social Media: @MomanGlobal ??<0xF0><0x9F><0x97><0xB3>️
▶️ https://moman.co/youtube

PDF preview unavailable. Download the PDF instead.

Moman Voice Activated Intercom H2 Pro User Guide ES ?v=1714042271

Related Documents

PreviewMOMAN H2 Helmet Intercom User Manual
User manual for the MOMAN H2 2-Rider Kit Helmet Intercom, detailing installation, operation, features like Bluetooth pairing, music playback, FM radio, and volume control.
PreviewMOMAN H2 PRO Headset Helmet Intercom User Manual
The MOMAN H2 PRO Headset Helmet Intercom User Manual provides comprehensive instructions for operating, installing, and maintaining the H2 PRO Bluetooth intercom system. Learn about features like music control, phone calls, FM radio, multi-intercom pairing, and troubleshooting for an optimal helmet communication experience.
PreviewMOMAN H2 PRO Helmet Intercom User Manual
Comprehensive user manual for the MOMAN H2 PRO motorcycle helmet intercom system, covering installation, operation, features, and specifications. Learn how to pair, control music, use FM radio, and more.
PreviewMOMAN H2 PRO Headset Helmet Intercom User Manual
User manual for the MOMAN H2 PRO Headset Helmet Intercom, detailing installation, operation, music control, phone functions, intercom pairing, and specifications. Learn how to use and care for your MOMAN H2 PRO.
PreviewMOMAN CP-S Motorcycle Helmet Intercom User Guide
A comprehensive guide to the features and operation of the MOMAN CP-S Motorcycle Helmet Intercom, covering phone calls, intercom functionality, and music playback.
PreviewMOMAN H4C Motorcycle Helmet Headset: User Manual & Features
Comprehensive guide to the MOMAN H4C motorcycle helmet headset, detailing its Bluetooth connectivity, integrated recorder, app control via Roadcam, and operational instructions. Includes specifications and care tips.
PreviewMoman H1 Motorcycle Helmet Intercom User Manual
User manual for the Moman H1 motorcycle helmet intercom system. Learn about product care, package contents, operation, and specifications.
PreviewMOMAN CP-S Motorcycle Helmet Intercom User Guide
This guide provides instructions and specifications for the MOMAN CP-S Motorcycle Helmet Intercom, covering features, operation, and technical details.