MOMAN H2 Headset Helmet Intercom - 2-Rider Kit

Caring For Your MOMAN Product

• Keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids, and heat sources away from the product.
• Use only a soft and dry cloth for cleaning.
• Avoid dropping or impact.
• Do not attempt to disassemble the product; this voids the warranty.
• Have malfunctions checked or repaired by authorized technicians.
• Warranty does not apply to human errors.

Package List

• Intercom x2
• Velcro Clip x2
• Back Clip x2
• Butterfly sticker x1
• Hook and Loop Fasteners x2
• 1 Pair of Speakers with Microphone x2
• Manual x1
• USB Cable x2
• Screw Driver x2
• Headphone Velcro x8

Product Introduction

The MOMAN H2 is a 2-rider kit headset helmet intercom system.

Key Components:

• ① On/Off Key
• ② Indicator Light
• ③ Function Key
• ④ Charging Interface (Type-C)
• ⑤ Knob
• ⑥ Headset Interface
• ⑦ Buckle Flap
• ⑧ Speaker
• ⑨ Headset Plug
• Microphone

Operation

1. Power On/Off

• ON: Press the On/Off Key for 2 seconds. Blue indicator flashes twice, system enters standby mode.
• OFF: Press the On/Off Key for 2 seconds. Red indicator flashes twice, system powers off.

2. Pairing & Disconnection

2.1 with Two Intercoms

• Pairing: Power on both intercoms. Their indicators will flash red and blue alternatively. Press the On/Off Key of one intercom for 2 seconds (voice prompt "Intercom Search"). Indicators will flash blue quickly. After a few minutes, they pair automatically (blue indicator flashes slowly).
• Disconnect: Press the Function Key for 2 seconds to disconnect. Press again to reconnect.

Note: Keep intercoms within 1 meter for pairing. Once paired, they reconnect automatically in standby mode. Automatic connection is available within five minutes of disconnection; otherwise, manually press the Function Key once.

2.2 with Mobile Phone

• Pairing: After power on, indicators flash red and blue alternatively. Turn on your mobile phone's Bluetooth, search for "MOMAN H2" and pair. Voice prompt "Bluetooth connected".

Note: Keep intercom and mobile phone within 1 meter. If a pairing record exists, they will connect automatically when powered on with Bluetooth enabled.

3. Phone Control

• Answer Call: Press the Function Key.
• Automatic Answer: If no operation within 8 seconds of an incoming call, it answers automatically.
• Reject Call: Press and hold the Function Key for 3 seconds until "beep".
• End Call: Press the Function Key.
• Redial: In standby mode, press the On/Off Key twice to dial the last number.

4. Music

• Play/Pause: Press the Function Key (under Bluetooth connection).
• Next Music: Turn the Knob counterclockwise.
• Previous Music: Turn the Knob clockwise.

5. Volume Adjustment

• Decrease Volume: Continuously turn the Knob counterclockwise.
• Increase Volume: Continuously turn the Knob clockwise.

Note: Voice alarm for maximum or minimum volume.

6. FM Radio

• Turn On: In standby mode, press the Function Key twice to switch to FM radio.
• Select Channels: Quickly rotate and release the Knob to adjust channels. Continuously rotate the Knob to select different channels.
• Turn Off: Press the Function Key twice to return to the previous mode.

Note: For weak indoor signals, try near a window or in an open area. If a call comes in while FM radio is on, the radio will pause and connect to the phone; it resumes after the call ends.

7. Multi-Mode Switch

7.1 Between Intercom and Music/FM Radio:

• Exit Intercom: In intercom mode, press the Function Key for 2 seconds (hear "beep") to exit intercom mode and switch to Music/FM radio.
• FM Radio On/Off: Press the Function Key twice.
• Music On/Off: Short press the Function Key.
• Back to Intercom: Long press the Function Key.

7.2 Between Intercom and Mobile Phone:

If the device is connected to a mobile phone, the intercom will disconnect during a call. It will automatically return to intercom mode after the call ends (takes 5 seconds).

7.3 Function Priority

1. Mobile Phone
2. Intercom
3. Music/FM Radio

8. Language

When the device is on, press the On/Off Key and rotate the Knob to change the voice prompt language.

Installation

Method 1: Install with Back Clip

1. Loosen the screws of the back clip using the screwdriver to open it.
2. Open the helmet liner, insert the clip onto the left side of the helmet, and tighten the screw.
3. Slide the intercom into the back clip slot until it locks firmly.
4. Open the helmet liner (ear position), clean the EPS surface, and stick a piece of horn Velcro on each side.
5. Attach the speaker to the Velcro surface. The speaker with the short line should be closer to the intercom. Fix the microphone and manage the cables.
6. Insert the headset into the intercom jack and secure the cable.

Method 2: Install with Velcro Clip

1. Separate the hook and loop fasteners. Stick the hook onto the Velcro clip.
2. Choose the installation position on the helmet and stick the loop fastener to it.
3. Install the intercom onto the Velcro clip.
4. Refer to Method 1 for speaker installation.

2. How to Remove the Intercom from Helmet

Unplug the headset. Press the fixed buckle in the middle of the back clip with one finger (towards the helmet side) to detach the hook from the intercom. Push the intercom upwards to slide it out of the back clip.

3. How to Fix the Headset Plug (If necessary)

Unscrew the screws on the back of the intercom, open the buckle flap, plug in the headset, and tighten the screws. To unplug, unscrew and open the flap.

Charging

1. Use the attached charging cable to charge the intercom. Connect the Type-C end to the intercom and the USB end to a power source (computer USB, mobile power supply with DC 5V output, or USB power adapter with DC 5V output).
2. During charging, the red LED is on. It turns off slowly when fully charged. Full charge takes up to 2.5 hours.

Notes

• If not using for over a month, charge the intercom every two months to protect the lithium battery.
• Store the product between -20 °C to 50 °C. Avoid extreme temperatures.
• Do not expose to fire to prevent explosion.
• Only the two screws on the back of the intercom can be opened. Do not open other screws to avoid damage.

Specifications