Kohler Archer Heated BubbleMassage Air Bath K-1947-GHRA

Features

• 120 airjets release thousands of heated bubbles that surround and support the body in a warm massage.
• Purge cycles remove residual water from air channels after use to keep the system clean.
• Variable-speed blower lets you adjust massage intensity to 18 levels.
• Comfort Depth® design offers a convenient 19" step-over height while retaining the same depth as a standard 21" bath.
• Molded lumbar support offers extra comfort while bathing.
• Slotted overflow allows for deep soaking.
• Integral apron.
• Integral flange helps prevent water from seeping behind wall and simplifies alcove installation.
• Bottom surface manufactured with textured appearance.
• Right-hand drain.
• Coordinates with other products in the Archer® collection.

Material

Acrylic.

Hydrotherapy

Heated BubbleMassage™.

Technology

• Built-in 600W BubbleMassage™ heater warms humidified air before it enters the bath.
• Bath includes auto purge (after bath drains) and manual purge cycles to remove residual water and keep system clean.
• Auto-shutoff timer on blower allows users to enjoy Heated BubbleMassage™ experience for 60 minutes before turning off.
• User interface: electronic keypad control.

Installation

• Three-wall alcove.
• User interface: electronic keypad control.

Required Products/Accessories

• K-7271 Brass Slotted Overflow Bath Drain
• K-7272 PVC Slotted Overflow Bath Drain

Recommended Products/Accessories

• K-1446 Remote Installation Kit
• K-24916 Wireless Music Kit

Codes/Standards

• ADA
• ASME A112.19.7/CSA B45.10
• CSA B45.5/IAPMO Z124
• ASTM E162
• ASTM E662
• UL 1795
• CSA C22.2 No. 218.2
• Greenguard UL 2818 - Gold
• ICC/ANSI A117.1

KOHLER® Hydrotherapy Components

• Five-Year Limited Warranty
• KOHLER® Plastic Baths and Receptors Lifetime Limited Warranty

See website for detailed warranty information.

Available Colors/Finishes

Color tiles intended for reference only.

Technical Information

• Installation: Three-wall alcove
• Drain location: Right
• Weight: 113 lbs (51.3 kg)
• Minimum floor load: 48.2 lbs/ft² (235.3 kg/m²)
• Water depth: 15-1/8" (384 mm)
• Water capacity: 57 gal (215.8 L)
• Electrical component rating: Blower: 120 V, 10 A, 60 Hz; Heater: 120 V, 5 A, 60 Hz
• Minimum flat for door: 2" (51 mm)

Required Electrical Service

Two dedicated circuits required, protected with Class A Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD).

• Blower: 120 V, 15 A, 60 Hz
• Heater: 120 V, 15 A, 60 Hz

Notes

• Measure your actual product for rough-in details.
• Install this product according to the installation instructions.
• The hot water supply should be 70% of the capacity of the bath or greater. Installations will vary.
• Provide one grounded electrical outlet within 24" (610 mm) of each component.
• Remote blower installation kit is available for relocating the blower. Provide access for servicing the blower.
• Do not relocate or alter the PVC tee or coiled flexible tubing connected to the blower. Follow the blower relocation instructions exactly.
• ADA compliant when installed to the specific requirements of these regulations.

Dimensions

Diagrams show overall dimensions. See Technical Information for specific measurements.

Top View:

• Overall length: 60" (1524 mm)
• Overall width: 30" (762 mm)

Side View:

• Overall height: 20" (508 mm)
• Step-over height: 19"
• Lumbar Angle: 24°

Drain Detail:

• Drain location: Right
• Bath Drain: 1-1/2"
• Integral Flange Detail: 3/8" (10 mm) R

Contact Information

For the most current Specification Sheet, go to www.kohler.com.

Customer Service: 1-800-4KOHLER (1-800-456-4537)