Schlage Ease S2 Smart Lever Lock: Quick Start Guide

What's in the Box

• Mounting screws (3) - Two lengths provided
• Lever spigot
• Cover screws (4)
• Strike plate & screws
• 4 x AA Alkaline batteries

Door Preparation & Measurements

The latch mechanism allows for adjustable backsets. The spindle hole position can be slid to accommodate either a 60mm (2-3/8 inch) or 70mm (2-3/4 inch) backset.

Diagram shows measurements: 54mm (2-1/8 inch) for the latch faceplate, and options for 60mm (2-3/8 inch) or 70mm (2-3/4 inch) backset.

Installation Steps

1. Install the latch onto the door, ensuring the pin side of the latch is facing away from the door jamb/frame. Note: The cable must go through the door hole above the latch.
2. Ensure the spindle is square. The hole shown is for an optional cross bolt provided for stabilizing the lock. If a hole was drilled for this, securely tighten the post before mounting on the door.
3. Position the inside mounting plate to sit flush on the door, ensuring the cable and spindle go through the holes in the mounting plate. Secure both assemblies using the 8/32 screws provided. Make sure the exterior assembly is vertically aligned. If the cross bolt was added, securely tighten its post to the exterior unit with the additional screw provided.
4. Attach the cable assembly to the interior assembly PCB by lining up the notches on the top of the cable connector with the slots on the PCB connector. Press the connector in firmly until completely connected.
5. Install the interior assembly onto the inside mounting plate. Secure using 4 screws through the interior assembly onto the mounting plate.
6. Install batteries and battery cover.
7. Insert the cylinder into the lever, ensuring the cylinder sits flush within the lever.
8. Using a flat head screwdriver, ensure the turnplate is set vertical.
9. Insert the key into the cylinder and ensure the key is horizontal. Check handing to ensure the lever is pointing towards the hinges. Push the lever onto the lever spigot; you may need to turn the key to click the lever into place.
10. Install the internal lever, ensuring the handle points towards the door hinges.
11. Install the strike into the door jamb.

Warnings & Finish Care

• Do not install batteries until the lock is completely installed on the door.
• Failure to follow these instructions could result in damage to the product and void the factory warranty.
• The accuracy of the door preparation is critical for the functioning and security of this product. Misalignment can cause performance degradation and lessening of security.

Finish Care

This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Do not use lacquer thinner, caustic soaps, abrasive cleaners or polishes as these can damage the coating and result in tarnishing.

Definitions

Fake PIN code

Random numbers that are added before or after the user PIN. This prevents the user PIN from being exposed.

Master mode

The master mode could be entered by entering [Master PIN Code #] to program the lock.

Master PIN code

The master PIN code is used for programming and for feature settings.

Passage mode

The lock can be switched to passage mode by toggling the switch on the internal side. In this mode, it is unlocked inside/out and you may enter freely. You may still lock the unit externally by holding any key for 2 seconds. It will resume passage mode when unlocked via PIN or key override until the passage mode switch is shifted to the locked position. Note: Enabling and disabling passage mode can only be done on the internal side of the unit via the switch.

Reset button

After reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to page 11 for instructions on how to reset your lock.

Shutdown time

The lock will shutdown for a default of 3 minutes and not allow operation after the wrong code entry limit (5 times) has been met. When the unit is in shutdown, the light will flash if you are trying to use the keypad.

Silent mode

Disables the tone sound.

Status indicators

Located on exterior assembly.

User PIN code

The user PIN code operates the lock. Maximum number of user PIN codes is 20.

Hardware Specifications

Notes

• Operation temperature: -20°C to 55°C
• Battery lasts up to one year (10 times open/close per day)

Programming Options

To program the lock, you must first enter Master Mode by pressing the Master PIN code.

• Change Master PIN Code: Press Master PIN code, Press New master PIN code, Repeat New master PIN code.
• Add User PIN Code: Press Master PIN code, Press New user PIN code, Repeat New user PIN code.
• Delete User PIN Code: Press Master PIN code, Press Old user PIN code.
• Enable Beeper: Press Master PIN code, Press 1.
• Disable Beeper: Press Master PIN code, Press 0.
• Enable Bluetooth: Press Master PIN code, Press 1.
• Disable Bluetooth: Press Master PIN code, Press 0.

Notes

• 1. After each successful setting entry, 2 green lights and 2 beep indicators will occur.
• 2. The beeping sound occurs only when sound is enabled.
• 3. If the indicators show 3 red lights and 3 beeps, your setting has failed and the system will exit master mode. Please enter master mode to try again.
• 4. Refer to page 9 for guidelines on setting PIN codes.

Setting PIN Codes

1. Master PIN Code (4~10 digit): Default master PIN code is "12345678". It is essential the master PIN code is modified after installation to complete the setup process. If you forget your master PIN code, you can reset your lock back to factory settings (refer to page 11 for instructions).
2. User PIN Code (4~10 digit): User PIN codes can be set up through master PIN code. Up to 20 user PIN codes can be stored.
3. Both master and user PIN codes don't support the following combination of numbers.

Normal Mode Operation

1. Enter the master or user PIN code, followed by #, then rotate the lever to open the door. Door will automatically re-lock 7 seconds later. If you wish to deactivate the 7-second auto re-lock feature, switch to passage mode (page 10).
2. Alternatively, use the backup key provided.

Emergency Power and Warranty

Emergency Battery Power

If the unit is locked and you require emergency battery power, a micro USB port is located on the bottom of the external unit. Using a micro USB cable and a charged power bank, you can power the lock to regain access as required.

Warranty Conditions

The Schlage Ease™ provides a 2-year mechanical and electronic warranty. Goods come with guarantees that cannot be excluded under local consumer law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Resetting and Mobile App Integration

Resetting Your Lock

If you need to reset your lock, the reset button is located under the left-most battery in the battery casing. Use a pointed object, press and hold the reset button for over 5 seconds until you hear a beep.

Mobile App Integration

For an enhanced experience and additional functionality, try using the Schlage Ease™ with the Schlage Abode mobile application. Simply download the Schlage Abode app from the Apple App Store or the Google Play Store. Manage and control your lock with the ease of your smartphone for greater control and access.

Contact Information

Allegion Support

Australia
Phone: 1800 098 094
Email: info.au@allegion.com
Website: www.allegion.com.au/ease

New Zealand
Phone: 0800 477 869
Email: nzinfo@allegion.com
Website: www.allegion.co.nz/ease

South East Asia
Phone: +65 6488 2562
Email: sea.info@allegion.com
Website: www.allegion.com

ALLEGION