Ascent Series
Homeallegion.co.nz/finisheswarranty
Home
User Guide for SCHLAGE models including: 2411, Schalge Ascent Smart Lever, Schalge Ascent Lever, Schalge Ascent, Smart Lever, Lever
Jun 1, 2025 — Conceal battery screw with provided screw cover. With the door in the open position test lock operation: A. Rotate the external lever, ensure latch does not ...
File Info : application/pdf, 12 Pages, 1.65MB
DocumentDocumentSchlage Ascent SMART LEVER Quick Start Guide Parts Tools required Tape measure Pencil Level Drill Drill bit - Ø10mm Door thickness 32mm - 55mm 3 9A Hole saw - Ø54mm Screwdriver (Phillips #2) Spade bit - Ø25mm (timber door) Hole saw - Ø25mm (metal door) 1A 1B 6 4A 9B 2B 2A 4B 7 8 5A 5B 12 10 11 Components 1 A. External lever B. Rubber gasket 2. A. Internal lever B. Rubber gasket 3. 4x AAA alkaline batteries 4. A. 60/70mm adjustable deadlatch B. 2x Latch fixing screws 5. A. Strike plate B. 2x Strike plate fixing screws 6. 2x Screw standoffs (M4) 7. 2x Mounting screws (M4x30mm) 2x Mounting screws (M4x45mm) 8. 2x Screw covers 9. A. Battery cover B. Battery cover screw and screw cover 10. Hex tool for battery compartment 11. Reset pin 12. 3x Key tags For more information visit schlage.co.nz/ascent Fixing pack Door thickness Mounting screws Installation fixings 32mm - 40mm 41mm - 55mm 2x M4x30mm CSK screws 2x M4x45mm CSK screws 2x M4x30mm Screw standoffs 2x M4 Screw covers 1x Screw cover for battery compartment screw 1x Reset pin 1x Hex key Deadlatch fixings 4x M4x20mm CSK screws for wooden door 4x M3.9x16mm CSK screws for aluminium door External lock body Fingerprint Keypad / keytag Internal lock body Emergency USB-C port Installation 1. Option A: Prepare the door Replace an existing lock 3 32-55mm A. Remove existing door handle. Most handles can be unscrewed from the internal side. B. Check that your door meets the installation requirements: A 1. Standard 54mm diameter cut-out. 2. Backset of 60mm or 70mm from edge of door to centre of cut-out. 3. Door thickness between 32 and 55mm. C. Remove the latch from the side of the door. 1 Ø54mm Reset button Battery cover 2 Backset 60/70mm C 2 1. Option B: Prepare the door New doors Professional installation is recommended for new doors. PREFORATED CUT 3. Prepare jamb and install strike If jamb preparation is required, we recommend contacting a locksmith for installation. A. Your door must have a thickness between 32mm and 55mm. B. Follow the Schlage Ascent smart lever template to prepare your door. 2. Install latch A. Latch comes in 60mm backset position. If required, pull latch case to extend to 70mm backset position. B. Mount latch into position using fixing screws. C. Ensure that the spindle hole is square to the door. BACKSET 70mm BACKSET 60mm Fit here on door edge 4.0 mm FOLD HERE Ø25mm 90mm Deep LATCH HEIGHT A. Install strike and dust box as provided in box. B. Adjust strike anti-rattle tab to achieve a firmly held and sealed door. Ø54mm 4. Install levers 1. 2. Ø70mm A. Fit the two screw standoffs onto the external lever. B. Fit the rubber gaskets on both levers if not already installed. C. Use the hex tool to loosen the screw behind the exit lever and remove the battery cover. The screw should remain in place in the housing. The beveled edge of the latch should face the strike plate so that it will retract automatically. 3 4. Install levers cont. D. Position the external lever to the outside of your door, aligning the spindle, standoffs, and cable with the holes in your door and latch. Push the lever in until it is flush against the door, and hold it in place until the next step. 5. Install batteries A. Install 4x AAA batteries, replace the battery cover and tighten battery cover screw. B. Conceal battery screw with provided screw cover. E. From the inside of your door, install the internal lever and second rubber gasket by passing the cable through the base and handle to the battery compartment and connecting it to the port. Using the provided mounting screws secure the two levers together. Before tightening the screws, check that the lever set is aligned correctly. NOTE: We recommend using quality alkaline batteries. Do not use zinc carbon batteries. 6. Test latch operation With the door in the open position test lock operation: A. Rotate the external lever, ensure latch does not retract. B. Rotate the internal lever, ensure latch does retract. Touch keypad to active keypad and test operation using code 123456 (ignore voice prompt during test). 4 Pair and programme lock Get mobile access with Schlage Breeze For an enhanced experience and additional functionality, we recommend you download the Schlage Breeze mobile app from the Apple App Store or the Google Play Store. Apple App Store Google Play Store Schlage Breeze app user functions Within the Schlage Breeze app, users have access to more features than those available on the lock itself. This guide provides information on many of the features available. Status of lock Use the locked and unlocked icons to easily lock or unlock your door, or simply to check the status of the lock (locked or unlocked). 1. Create a user account using your email address (or login if you have an existing account). 2. Ensure Bluetooth is enabled on your phone, tap the keypad of your Schlage Ascent smart lever to activate it. 3. To pair the lock with the app, click on the + and follow the instructions on the app. PIN codes The Schlage Ascent allows you to store up to 150 PIN codes - either custom, permanent, recurring or scheduled. Default master PIN code is 123456 Master PIN codes must contain 6-11 digits Custom created codes can contain 4-9 digits To add a new PIN code, use the Grant Access icon, add PIN code. For a customised PIN code, use the custom feature, add your guest's name, and set your PIN code. To manage your PIN codes, select Manage Access and update or delete user access as required. 5 Virtual keys When you regularly need to share access to many guests, you can message them PIN code access. This is a great solution for home share properties. Select Grant Access, Invite Breeze User and enter the details for your guest. You can share this virtual key by various options including email or text message. Key tags The Schlage Ascent allows you to store up to 150 key tag credentials. Three key tags are provided with your Schlage Ascent smart lever, additional key tags can be purchased through your local door hardware retailer. To set up your key tags, select Grant Access, Add Credential, ensure you name your key tag and complete set up of your credential. To manage your credentials, select Manage Access and update or delete user access as required. Auto locking The Schlage Ascent smart lever default is set with a 5 second auto lock, this can be changed in the Settings, Auto Lock function by selecting a different time delay. Passage mode The lock can be switched to passage mode in the Schlage Breeze app within the Settings function. In this mode, the internal and external lever is unlocked, and you may enter freely. You can either set specific days/times to operate passage mode or disable this feature. When passage mode is in operation, you may still lock the unit externally by holding the key for 3 seconds. It will resume passage mode when unlocked via PIN, key tag or key override until the passage mode period completes or the feature is disabled via the Schlage Breeze app. Clock After installation of your lock and registering for the Schlage Breeze app, the clock is automatically set to your local time. The lock has a feature within the Settings function to change to daylight savings, if you use the scheduled PIN code feature, ensure you change to current daylight savings time to ensure the correct time is used by the lock. Lock notifications history To view the audit trail of when the lock was used and by which Sarah user, select History. This provides information on your users, Rachel timing, or any attempts of adding Rachel incorrect PIN codes. Mike Grandpa Lock sound To enable or disable the lock sound select Settings, Lock Sound. Note, by disabling the sound, both the lock voice prompts and beeps will be disabled. 6 Fingerprint access The Schlage Ascent smart lever allows you to store up to 150 fingerprints. To set up your fingerprint access, select Grant Access, Add Fingerprint, ensure you name your fingerprint and complete set up. Your Schlage Ascent smart lever will then prompt you with directions on how to add your fingerprint. To manage your fingerprint access, select Manage Access and update or delete user access as required. Manual programming Note for installer Administrator code set up Once the lock is installed on the door, the lock requires the default admin code to be changed. Refer to manual lock operation on page 8 to change the default admin code and set new PIN code/s. Once PIN code/s are set, the lock voice command will no longer prompt for the lock to be paired to a mobile device. Note If the lock is connected to the homeowners Schlage Breeze mobile app, then this step is not required. IMPORTANT: Note for homeowner Manual factory reset If your lock was installed by someone other than yourself, we highly recommend you complete a factory reset on the lock to ensure all previously set PIN codes are successfully deleted. 1. Remove the battery cover and using a pointed object, press the reset button for 4 seconds (refer below or to page 2 for the location of the reset button). 2. The lock will prompt to enter a setup code. At this point enter 000 on the keypad. 3. The lock will prompt that the reset procedure is complete. 4. The lock is now available to be paired with a mobile device using the Schlage Breeze app. Reset button Battery cover 7 Manual lock operation Follow this simple chart if you are manually programming your lock. Further lock functions are available using the Schlage Breeze app, refer to pages 5-7 for more information. Change Default Admin Code Press 1 2 Press 1 2 3 4 5 6 Press New admin code Repeat New admin code Press Change Admin Code Press 1 2 Press Admin code Press New admin code # Repeat New admin code Press Add User Code Press 8 0 Add Key Tag Press 8 0 Press Admin code Press Admin code Press New user code # Present One or more key tag#s Repeat New user code Press Press Delete All Passwords Press 7 1 Press Admin code Press Delete All Key Tags Press 6 9 Press Admin code Press Hardware specifications Item External and internal assemblies Battery Specifications 68mm (L) x 159mm (W) x 59mm (D) AAA alkaline battery x 4 (Operation voltage: 4.8 to 6V) Notes Operation temperature: -20ºC to 50ºC Lasts 6-12 months depending on usage 6 months with Schlage Wi-Fi Bridge (BZ100) 8 Schlage Ascent smart lever functions Refer to the manual lock operation on page 8 for further instructions on manually programming your lock. Tips · To activate and illuminate the keypad, press the key. · Always press the key after entering your PIN code. Random PIN code This security feature allows a user to randomly enter digits before and/or after the PIN code to prevent the user PIN code from being exposed. Fake PIN User PIN User PIN Fake PIN Tamper alert The Schlage Ascent smart lever allows for four attempts to correctly input your code, on the fifth incorrect entry the lock alarm will sound. The alarm sounds for 30 seconds, during this time you cannot continue to enter PIN codes. You can however unlock the lock through the Schlage Breeze app which will also turn the lock alarm sound off. Low battery notification The keypad flashes to notify you when the battery is low, with a voice prompt saying, `Battery low please replace'. Also, while in the Schlage Breeze app, the app will display a low battery notification. Emergency power If your Schlage Ascent smart lever is locked and you require emergency battery power, located on the bottom of the external lock body is a USB-C port. Using a USB-C cable and charged power bank, you can power the lock to regain access as required. 9 Warranty conditions The Schlage Ascent provides a 2 year mechanical and electronic warranty. Our goods come with guarantees that cannot be excluded under the local consumer law. You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty does not cover any defect or damage which may be caused or partly caused if the goods are not properly maintained, installed or are not suitable to the specified application. Refer to our website for our finish warranty www.allegion.co.nz/finisheswarranty. Schlage Wi-Fi Bridge (BZ100) Empower your Schlage Ascent smart lever with Wi-Fi capability. The Schlage Wi-Fi Bridge (BZ100) pairs to your Schlage Ascent smart lever, to provide you with a real-time connection through your smartphone. Ask your retailer about the Schlage Wi-Fi Bridge (BZ100), sold separately. Factory default settings Settings Master PIN code Beeper Wrong code entry limit Bluetooth mode Factory default 123456 Enabled 5 times Enabled Refer to page 7 for instructions on how to complete a factory reset if required. Care and maintenance Door furniture At six (6) monthly intervals, the fixing screws securing the furniture to the door, both surface fix and through fix, should be checked and tightened as required. Loose fitting furniture which fails will not be covered under warranty. All door furniture should only be wiped clean with a soft damp cloth. A non-abrasive mild household detergent may be used to remove ingrained grime. Latch Care should be taken to ensure the internal components are kept free of dirt and filings during installation as this is the most common cause of malfunction and will not be covered under warranty. 10 For more information visit schlage.co.nz/ascent Australia 1800 098 094 info.au@allegion.com www.allegion.com.au New Zealand 0800 477 869 nzinfo@allegion.com www.allegion.co.nz © 2024 Allegion PDSC0061