DEKALA Smart Wake-Up Light
Model: A80S/AH80ST/AH80STM
User Manual
Safety Instructions
- To reduce the risk of fire, electric shock, or injury, read these instructions before use.
- This product is intended for household use, including similar use in hotels.
- Place the product on a stable, level, and non-slippery surface.
- Do not use this product in wet surroundings, such as bathrooms, near showers, or swimming pools.
- Do not allow water to run into or spill onto the product.
- Ensure the power adapter does not get wet during use.
- Only use the ORIGINAL adapter and USB cable provided.
- Do not use this product to reduce sleeping time; it aims to help you wake up more easily.
Maintenance and Care
- Clean the product with a dry and soft cloth.
- Do not use abrasive cleaning agents, pads, or solvents like alcohol or acetone, as this may damage the product's surface.
- If the product will not be used for an extended period, unplug the power adapter from the socket and store the product in a safe, dry place where it will not be crushed, bumped, or damaged.
What's Included
- Wake-Up Light
- USB Cable
- Adapter
- User Manual
Product Overview
The DEKALA Smart Wake-Up Light features the following components:
- 1. Alarm 1 button
- 2. Alarm 2 button
- 3. Down button
- 4. LED Light button
- 5. Up button
- 6. Snooze button
- 7. Volume + button
- 8. FM Radio button
- 9. Volume - button
- 10. Sleep Aid button
- 11. Time Setup/LED Display Mode button
- 12. LED Display
- 13. USB Output port
- 14. FM Antenna
- 15. Micro USB Input port
- 16. Speaker
- 17. Button Cell Compartment
Getting Started
- Remove the insulation film from the Button Cell Compartment at the bottom of the device.
- Connect the Wake-up Light to power using the provided USB Cable and Adapter. Note: The product has no power on/off button; it activates upon plugging in the adapter. Unplug the adapter to disconnect power.
- For FM Radio reception, loosen the tie securing the FM Antenna (14) and unroll the wire.
Operation Guide
Time Setting
- Press and hold the Time Setup/LED Display Mode button (11) for 2 seconds until the Hour digits flash on the LED Display (12).
- Press the Up (5) or Down (3) button to adjust the Hour. Press the Time Setup/LED Display Mode button (11) to confirm and switch to setting the Minute.
- Press the Up (5) or Down (3) button to adjust the Minute. Press the Time Setup/LED Display Mode button (11) to confirm and begin setting the Clock Format.
- Press the Up (5) or Down (3) button to select between a 24-hour or 12-hour clock format. Press the Time Setup/LED Display Mode button (11) to confirm and complete the time setting.
Tip: If the 12-hour clock format is selected, AM or PM will be displayed accordingly.
Brightness of the LED Display
Press the Time Setup/LED Display Mode button (11) to cycle through the LED Display brightness modes: Day Mode (brightest), Night Mode (lowest), and OFF (display off).
Alarms
You can set up to two alarms directly on the device (Alarm 1 and Alarm 2). Alarms 3 and 4 can be set via the Smart Life app. The following describes setting Alarm 1:
- Press and hold the Alarm 1 button (1) for 2 seconds until the alarm icon and the Hour digits flash on the LED Display (12).
- Press the Up (5) or Down (3) button to adjust the Hour. Press the Alarm 1 button (1) to confirm and switch to setting the Minute.
- Press the Up (5) or Down (3) button to adjust the Minute. Press the Alarm 1 button (1) to confirm and proceed to Ringtone Setting.
- Press the Up (5) or Down (3) button to select your preferred ringtone (S-01 to S-07 for nature sounds, F-08 for the last FM station). Press the Alarm 1 button (1) to confirm and proceed to Volume Setting.
- Press the Up (5) or Down (3) button to adjust the ringtone volume (U-01 to U-16). Press the Alarm 1 button (1) to confirm and proceed to Sunrise Light Setting.
- Press the Up (5) or Down (3) buttons to adjust the brightness level for the sunrise light (L-01 to L-20). Press the Alarm 1 button (1) to confirm and proceed to setting the sunrise time.
- Press the Up (5) or Down (3) button to select the duration for the sunrise simulation (10, 20, 30, 40, 50, or 60 minutes before the alarm time). Press the Alarm 1 button (1) to confirm and complete the settings for Alarm 1. Alarm 1 is now active.
Tips:
- If you select a 10-minute sunrise time and set the alarm for 7:00 AM, the light will begin to illuminate at 6:50 AM, gradually increasing in brightness until it reaches the level set in Step 6 by 7:00 AM.
- If L-00 (Light off) is selected, there will be no sunrise light, only the ringtone will sound when Alarm 1 rings.
- To permanently cancel Alarm 1, press the Alarm 1 button (1) when it is not the alarm time. The same applies to Alarm 2.
Snooze
When the alarm rings, press the Snooze button (6) to activate the Snooze Mode, which delays the alarm for 9 minutes. You can snooze up to 5 times. Pressing the corresponding Alarm button (1 or 2) will manually stop the alarm. If no action is taken within 15 minutes of the alarm sounding, it will automatically stop for that instance.
FM Radio
- Press the FM Radio button (8) to turn the FM radio on or off.
- Before first use, press and hold the FM Radio button (8) for 2 seconds to initiate an automatic FM station search. Available stations will be saved sequentially as P-01, P-02, etc.
- Use the Up (5) or Down (3) buttons to switch between the saved FM stations (P-01, P-02, etc.).
- Use the Up (5) or Down (3) buttons to adjust the volume (U-01 to U-16).
Note: For optimal reception, ensure the FM antenna (14) is fully unwound and positioned for the best signal.
Sleep Aid
The Sleep Aid feature simulates a sunset to help you fall asleep more easily. The sunset light will gradually dim, and the selected nature sound volume will decrease over time.
- Press the Sleep Aid button (10) to enable the feature.
- Press the Up (5) or Down (3) buttons to adjust the brightness level of the light (L-00 for off, L-01 to L-20 for brightness levels).
- Press the Sleep Aid button (10) to confirm your selection and then press the Up (5) or Down (3) buttons to choose your preferred sleep sound (S-00 for off, S-01 to S-03 for nature sounds).
- Press the Sleep Aid button (10) to confirm your selection and then press the Up (5) or Down (3) buttons to adjust the volume of the sound (U-01 to U-16).
- Press the Sleep Aid button (10) to confirm your selection and complete the Sleep Aid setup. The feature is now enabled.
Tip: Press the Sleep Aid button (10) again to disable the feature.
Light Functions
Bedside Light
Press the LED Light button (4) to turn the bedside light on or off. Use the Up (5) or Down (3) buttons to adjust the brightness level.
Atmosphere Light
Double press the LED Light button (4) to activate the Atmosphere Light, which cycles through colors automatically. Short press the Up (5) or Down (3) buttons to manually change the light color one by one (7 colors are available). Long press the Up (5) or Down (3) buttons, and the light will automatically cycle through colors after you release the buttons. Short press the LED Light button (4) again to turn off the Atmosphere Light.
Contact Information
For further assistance or inquiries, please contact DEKALA:
Email: info@dekalastore.com
DEKALA also offers new arrival products for testing. Customer feedback is highly valued.