TS710 – V2 Single Channel Timer
Diegimo vadovas
TS710 – V2 Single Channel Timer
FP720 – V2 Two Channel Programmer
Diegimo vadovas
1. Diegimo žingsniai
Vartotojo vadovą galima atsisiųsti iš: fűtés.danfoss.com.
- Montavimą turi atlikti įgaliotas elektrikas.
- Remove and mount timer/programmer back plate
direct to wall or on wall box, and wire as required for
application, see fig. 1 & 2 on page 16. The backplate
included within the product packaging should be
used for the installation. - Nuimkite akumuliatoriaus atsarginės dalies skirtuką, žr. 3 17 puslapyje.
- Locate hooks at top of timer/programmer into top of
back plate, lower into position and tighten retaining
varžtais.
2. Dimensions and Wiring
See fig. 4 for dimensions and fig. 5 for wiring diagram
on page 18 and page 19.
3. Techninės specifikacijos
|
Specifikacijos |
TS710 – V2 |
FP720 – V2 |
|
Operacija |
Nuolatinis naudojimas |
|
|
Veikimo ttage |
230 Vac ± 10 % 50/60 Hz |
|
|
Išvestis |
Voltas nemokamai |
2 x 230 Vac |
|
Perjungti reitingą |
3A (1) esant 230 Vac |
|
|
Jungiklio tipas |
1x SPDT Type 1B |
2x SPDT Tipas 1B viduje susieta |
|
Terminalai |
maksimalus 2.5 mm2 laidai |
|
|
IP reitingas |
IP30 (įdiegta) |
|
|
Statyba |
EN60730-2-7 |
|
|
Kontroliuoti taršą situacija |
2 laipsnis |
|
|
Įvertintas impulsas ttage |
4 kV |
|
|
Programinė įranga classi cation |
A |
|
|
Laikymo sąlygos |
Santykinė oro drėgmė 5–95 % Ambient (storage and shipping) -10 to 60°C |
|
This product is an electronic heating timer/programmer for control of domestic central heating and domestic hot water.
Danfoss Ltd.
22 Wycombe End, HP9 1NB,
„Danfoss A / S“
Klimato sprendimai • danfoss.com • +45 7488 2222
Bet kokia informacija, įskaitant, bet neapsiribojant, informaciją apie produkto pasirinkimą,
its application or use, product design, weight, dimensions, capacity or any other
technical data in product manuals, catalogues descriptions, advertisements, etc. and
whether made available in writing, orally, electronically, online or via download, shall
be considered informative, and is only binding if and to the extent, explicit reference is
made in a quotation or order confirmation. Danfoss cannot accept any responsibility
for possible errors in catalogues, brochures, videos and other material. Danfoss reserves
the right to alter its products without notice. This also applies to products ordered but
not delivered provided that such alterations can be made without changes to form, t
or function of the product. All trademarks in this material are property of Danfoss A/S
or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss
A/S. All rights reserved.
Dokumentai / Ištekliai
 |
Danfoss TS710 - V2 Single Channel Timer [pdf] Įdiegimo vadovas TS710, FP720, TS710 - V2 Single Channel Timer, TS710 - V2, Single Channel Timer, Channel Timer |
