MW MEAN WELL 200W PWM Output Driver User Manual

PWM-200KN series is a 200W AC/DC LED driver featuring the constant voltage mode with PWM style output, which is able to maintain the colour temperature and the brightness homogeneity when driving all kinds of LED strips and constant voltage LED bulbs.The built-in KNX interface is to avoid using the complicated KNX-DALl gateway and equipped with KNX Data Secure. KNX Data Secure offers protection against manipulation in building auto mation and can be configured in the ETS project.
PWM-200KN operates from 100~305VAC and offers models with output voltage between 12V & 48V. Thanks to the high efficiency up to 94%, with the fanless design, the entire series is able to operate for -40°C ~ +85°C case temperature under free air convection.
The minimal dimming level low to 0.01% is suitable for low light level applications e.g. cinema. The output frequency is changeable up to 4KHz complaint lEEE1789-2015 no risk requirement and EU Ecodesign stroboscopic visibility measure(SVM) concern due to light fickering. requirement providing a great solution for health concern due to light fickering.

Model Encoding

Type	Function	Note
KN	KNX control technology	ln stock

SPECIFICATIONS

MODEL		PWM-200-12	PWM-200-24	PWM-200-36	PWM-200-48
OUTPUT	DC VOLTAGE	12V	24V	36V	48V
	RATED CURRENT	15A	8.3A	5.55A	4.17A
	RATED POWER	180W	199.2W	199.8W	200.1W
	DIMMING RANGE	0 ~ 100%
	PWM FREQUENCY (Typ.)	200~4000Hz user changable via ETS
	SETUP, RISE TIME Note.2	500ms, 80ms/230VAC, 1200ms, 80ms/115VAC
	HOLD UP TIME (Typ.)	10ms/230VAC or 115VAC
INPUT	VOLTAGE RANGE Note.3	100 ~ 305VAC 142 ~ 431VDC (Please refer to “STATIC CHARACTERISTIC” section)
	FREQUENCY RANGE	47 ~ 63Hz
	POWER FACTOR (Typ.)	PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC @ full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
	TOTAL HARMONIC DISTORTION	THD<20%(@load≧60%/115VAC, 230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section)
	EFFICIENCY (Typ.)	92%	93%	94%	94%
	AC CURRENT (Typ.)	2.2A / 115VAC 1.1A / 230VAC 0.9A / 277VAC
	INRUSH CURRENT (Typ.)	COLD START 65A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
	MAX. NO. of PSUs on 16A CIRCUIT BREAKER	3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 230VAC
	LEAKAGE CURRENT	<0.75mA / 277VAC
	STANDBY POWER CONSUMPTION	standby power consumption<0.5W when dimming off
PROTECTION	OVERLOAD	108 ~ 135% rated output power
		Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed
	SHORT CIRCUIT	Shut down o/p voltage, re-power on to recover
	OVER VOLTAGE	13 ~ 18V	27 ~ 34V	41 ~ 49V	53 ~ 65V
		Shut down o/p voltage, re-power on to recover after fault condition is removed
	OVER TEMPERATURE	Shut down o/p voltage, re-power on to recover after fault condition is removed
ENVIRONMENT	WORKING TEMP.	Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
	MAX. CASE TEMP.	Tcase=+85℃
	WORKING HUMIDITY	20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 ~ +80℃, 10 ~ 95% RH
	TEMP. COEFFICIENT	±0.03%/℃ (0 ~ 50℃)
	VIBRATION	10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC	SAFETY STANDARDS Note.5	UL8750( type ”HL” ), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13,BS EN/EN62384 independent, EAC TP TC 004,GB19510.1,GB19510.14 approved; Design refer to BS EN/EN60335-1, According to BS EN/EN61347-2-13 appendix J suitable for emergency installations.
	KNX STANDARDS	Certified protocol
	WITHSTAND VOLTAGE	I/P-O/P: 3.75KVAC
	ISOLATION RESISTANCE	I/P-O/P: 100M Ohms / 500VDC / 25℃/ 70% RH
	EMC EMISSION Note.6	Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3,GB17743 and GB17625.1,EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity, Line-Line 2KV),EAC TP TC 020
OTHERS	MTBF	553.6 K hrs min. Telcordia SR-332 (Bellcore) ; 170 K hrs min. MIL-HDBK-217F (25℃)
	DIMENSION	1956839.5mm (LWH)
	PACKING	1.03Kg; 12pcs/13.4Kg/0.71CUFT
NOTE	All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. De-rating may be needed under low input voltages. Please refer to “STATlC CHARACTERlSTlC” sections for details. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃or less. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitudes higher than 2000m(6500ft). For any application note and lP waterproof function installation caution, please refer our user manual before using. LED_EN [PDF] lt is not recommended to connect to capacitive loads Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

DIMMING OPERATION

Dimming principle for PWM style output

Dimming is achieved by varying the duty cycle of the output current.

KNXInterface

Apply KNX signal between KNX+ and KNX-.
The application program(database) can be downloaded via Online Catalogs from ETS or via http://www.meanwell.com/productCatalog.aspx

Parametrization options	Description
Switch functions	Turn on brightness Dimming speed for turn on/off Switch telegram and status Switch on/off delay
Dimming	Dimming speed for 0~100% Allow switch on via relative dimming
Brightness value	Dimming speed for transition brightness values Permit set switch on and off brightness via value Brightness value and status
More parameters can be found in the ETS application database and instruction manual
The device is equipped with KNX Data Secure. KNX Data Secure offers protection against manipulation in building automation and can be configured in the ETS project. Detailed specialist knowledge is required. A device certificate, which is attached to the device, is required for the first configuration. After configuration and ready for runtime (daily) operation, it is recommended to remove the certificate from the device and to store it securely. For details, please refer to the instruction manual. MEAN WELL Device Certificate

OUTPUT LOAD TEMPERATURE

AMBIENT TEMPERATURE,Ta (ºC)

Tcase (ºC)

STATIC CHARACTERISTIC

INPUT VOLTAGE (V) 60Hz

POWER FACTOR PF CHARACTERISTIC

LOAD

TOTAL HARMONIC DISTORTION (THD)

48V Model, Tcase at 75℃

Load

EFFICIENCY LOAD

PWM KN -200 series possess superior working efficiency that up to 94% can
be reached in field applications.
※ 48V Model, Tcase at 75℃

Load

LIFE TIME

Block Diagram

Mechanical Specification

Recommend Mounting Direction

Installation Manual

Connection for KN-type

Cautions

Before commencing any installation or maintenance work, please disconnect the power supply from the Ensure that it cannot be re-connected inadvertently!
Keep proper ventilation around the unit and do not stack any object on Also a 10-15 cm clearance must be kept when the adjacent device is a heat source.
Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a de-rating in output
Current rating of an approved primary /secondary cable should be greater than or equal to that of the Please refer to its specification.
For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the
Tc is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.
DO NOT connect “KNX- to -V”.
The power supply is considered as a component that will be operated in combination with final Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

For more information about installation, Please refer to: http://www.meanwell.com/manual.html for details.

Documents / Resources

MW MEAN WELL 200W PWM Output Driver [pdf] User Manual
200W PWM Output Driver, PWM-200KN

References

User Manual

Features

Applications

Description