Eterna PRSQMW Power and Colour Temperature Selectable IP65 LED Utility Fitting with Multi-Function Sensor Instruction Manual
EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from Electrical and Electronic Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/ GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST – DO NOT DISPOSE WITH HOUSEHOLD WASTE.
See website for more information on replacability and recycling
CLEANING
Clean this fitting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations.
READ THIS FIRST
Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product.
This product must be installed by a competent person in accordance with the current building and IEE wiring regulations.
As the buyer, installer and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability forloss, damage or premature failure resulting from inappropriate use.
This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Usingthis fitting in any other environments may result in a shortened working life, for example where there is prolonged periods of use or higher than normal ambient temperatures such as lighting public or shared spaces or in nursing /care home facilities.
Switch off the mains before commencing installation and remove the appropriate circuit fuse or lock off MCB.
Suitable for outdoor use.
This product is suitable for use in living areas, Bathroom Zone 2 and outsides of zones.
If being fitted in a bathroom a 30mA RCD must be used.
Bathroom Zones Diagram
This product is designed for permanent connection to fixed wiring: this must be a suitable circuit (protected with the appropriate MCB or fuse).
This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard and masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).
Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables.
The chosen location of your new fitting should allow for the product to be securely mounted (e.g. to a ceiling joist) and safely connected to the mains supply (lighting circuit).
When making connections ensure that the terminals are tightened securely and that no strands of wire protrude. Check that the terminals are tightened onto the bared conductors and not onto any insulation.
This product is double insulated, do not connect any part to Earth.
This product is not intended to be used by children and persons with sensory, physical and/or mental impairments that would prevent them from using it safely.
You are advised at every stage of your installation to double-check any electrical connections you have made. After you have completed your installation there are electrical tests that should be carried out, these tests are specified in the current IEE wiring and building regulations.
INTRODUCTION
The LED utility light incorporates a microwave sensing device which continuously scans the operating zone and immediately switches the light on when it detects movement in that area.
This means that whenever movement is detected within the range of the sensor the light will switch on automatically and illuminate the area you have selected to light. While there is movement within range of the unit the light will remain on.
A microwave sensor is an active motion detector emitting high-frequency electro-magnetic waves at 5.8GHz and receiving their echo. The sensor detectschange in the echo pattern within its detection zone and the light is then triggered. The wave can pass through doors, glass and thin walls and willcontinually monitor the signal within the detection area
LAMP REPLACEMENT
The light source is designed to last the lifetime of the luminaire.
The light source contained in this luminaire shall only be replaced by the manufacturer, service agent or a similar qualified person.
CAUTION, RISK OF ELECTRIC SHOCK.
INSTALLATION
Isolate mains and lock off.
Choose the location for your new fitting according to the conditions listed opposite.
- Unscrew gear tray screw and allow the gear tray to rest on its hinge.
- Drill holes in the back of your fitting for your fixing screws, take care and drill gently to ensure a clean hole through. Use a drill bit sized appropriately to your fixing screws (not supplied).
- Using the back of your fitting as a template, mark the position of your fixing holes on your mounting surface.
- Prepare the holes in your mounting surface as appropriate for your fixings.
- Pierce the rubber grommet in the back of your fitting making a hole just large enough to make a tight fit around the incoming mains cable.
- Thread the cable through the grommet and offer the fitting to the ceiling / wall.
- Secure the fitting in place. Note, if protection against ingress of moisture is required, the heads of screws must be covered with a silicone or similar sealant.
- Check that the grommet is still correctly fitted in the cable entry hole and around the incoming cable.
- Make the electrical connections to the terminal block according to the markings:
Brown to live (L)
Blue to neutral (N) - Set power to the desired option by selecting appropriate switch setting on the driver: 9W / 14W / 18W options
- Set colour temperature to the desired option by selecting appropriate switch setting on the driver.
DL Daylight 6500K CW Cool White 4400K WW Warm White 3000K - Set desired settings on the microwave.
- Replace gear tray and secure in position.
- Offer the diffuser onto the top of the fitting and tighten securely making sure the gasket is correctly fitted in place.
- Restore the power and switch on.
An Earth connection is not required for the operation of these Class II luminaires. The addition of the Earth terminal provides a loop-in/loop out facility which allows connectivity through to other Class I luminaires in the same lighting circuit.
NOTE: In warm white (3000K) and daylight white (6500K) operation only one set of LEDs will illuminate, in cool white (4400K) both sets of LEDs will illuminate.
UNDERSTANDING THE CONTROLS
REFER TO STEP DIM MICROWAVE SENSOR PICTURE OPPOSITE:
The motion detector can turn on the light based on movement. With this detector built in, light is automatically on when needed and dimmed to preset level before it is totally off.
SENSITIVITY DETECTION RANGE
Sensitivity can be adjusted by selecting the combination on the DIP switches for different applications.
| 1 | ||
| I | ON | 100% |
| II | OFF | 50% |
HOLD-TIME
Hold-time refers to the time period that the light remains 100% on if no more movement is detected.
| 2 | 3 | ||
| I | ON | ON | 5sec |
| II | ON | OFF | 90sec |
| III | OFF | OFF | 180sec |
| IV | OFF | ON | 10min |
DAYLIGHT SENSOR / THRESHOLD
Daylight threshold can be preset on DIP switches.
Light will always turn on upon movement if daylight sensor is disabled.
| 4 | ||
| I | ON | Disable |
| II | OFF | 10Lux |
CORRIDOR FUNCTION / STAND-BY TIME
This is the time period that the light remains at a low level before it is completely turned off.
| 5 | 6 | ||
| I | ON | ON | 0Sec |
| II | ON | OFF | 10Sec |
| III | OFF | ON | 10Min |
| IV | OFF | OFF | + |
CORRIDOR DIMMING LEVEL / STAND-BY DIMMING LEVEL
Light can be dimmed to different levels after hold time.
| 7 | ||
| I | ON | 10% |
| II | OFF | 30% |
STEP DIM MW SENSOR SPECIFICATIONS
| PRODUCT TYPE | STEP DIM MICROWAVE MOTION SENSOR |
| Operating Voltage | 220-240VAC 50/60Hz |
| HF System | 5.8GHz |
| Transmission Power | <0.2mW |
| Detection Angle | 150° Max |
| Power Consumption | <0.3W |
| Detection Range | Max. 6m adjustable |
| Dectection sensitivity | 50% / 100% |
| Hold time | 5s / 90s /180s / 10 min |
| Corridor function | 0s / 10s / 10 min / Disable |
| Corridor Dimming Level | 10% / 30% |
| Daylight sensor | 10 lux / Disable |
| Mounting | Indoors, ceiling and wall |
| Light Control | 10lux, disable |
| Working Temp | -20 to +60 degree |
| Rated Load | 400W (Inductive load) 800W (Resistive load) 270W (LED) |
- Detection Range
- Hold Time
- Daylight Sensor
- Corridor Function
- Corridor Dimming Level
Eterna Lighting Ltd
RED DIRECTIVE – Microwave Occupancy Sensor
Full declaration available at:
www.eterna-lighting.co.uk/red-declaration
| CIRCULAR OPAL | |||
| LED LAMP SPECIFICATIONS: | 9W | 14W | 18W |
| Luminaire lumens (with diffuser): Warm White, Cool White, Daylight White | 3000K – 1090 lm4400K – 1160 lm6500K – 1130 lm | 3000K – 1610 lm4400K – 1770 lm6500K – 1700 lm | 3000K – 1970 lm4400K – 2190 lm6500K – 2080 lm |
| Lumens from chip (array): Warm White, Cool White, Daylight White | 3000K – 1220 lm4400K – 1300 lm6500K – 1270 lm | 3000K – 1810 lm4400K – 1990 lm6500K – 1900 lm | 3000K – 2210 lm4400K – 2470 lm6500K – 2350 lm |
| Useful lumens (array): Warm White, Cool White, Daylight White | 3000K – 980 lm4400K – 1050 lm6500K – 1020 lm | 3000K – 1450 lm4400K – 1600 lm6500K – 1520 lm | 3000K – 1770 lm4400K – 1970 lm6500K – 1880 lm |
| Rated Wattage | 9W | 14W | 18W |
| Rated luminous flux | 3000K – 980 lm4400K – 1050 lm6500K – 1020 lm | 3000K – 1450 lm4400K – 1600 lm6500K – 1520 lm | 3000K – 1770 lm4400K – 1970 lm6500K – 1880 lm |
| Nominal life time of the lamp | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Colour temperature | 3000/4400/6500K | 3000/4400/6500K | 3000/4400/6500K |
| Number of switching cycles before premature lamp failure | ≥15000 | ≥15000 | ≥15000 |
| Warm-up time up to 60% of the full light output | Instant full light | Instant full light | Instant full light |
| Dimmable | No | No | No |
| Nominal beam angle | 120° | 120° | 120° |
| Rated power | 9W | 14W | 18W |
| Rated lamp lifetime | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Displacement factor | 0.97 | 0.97 | 0.97 |
| Lumen maintenance factor at end of nominal life | ≥80 | ≥80 | ≥80 |
| Starting time | Instant full light | Instant full light | Instant full light |
| Colour rendering | ≥0.8 | ≥0.8 | ≥0.8 |
| Colour consistency | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse |
| Rated peak intensity | 3000K – 243cd4400K – 260cd6500K – 252cd | 3000K – 361cd4400K – 396cd6500K – 378cd | 3000K – 441cd4400K – 492cd6500K – 468cd |
| Rated beam angle | 120° | 120° | 120° |
| Voltage / Frequency | 220-240V~50Hz | 220-240V~50Hz | 220-240V~50Hz |
| Lumen efficacy | 3000K – 121 lm / W4400K – 129 lm / W6500K – 126 lm / W | 3000K – 115 lm / W4400K – 126 lm / W6500K – 121 lm / W | 3000K – 109 lm / W4400K – 122 lm / W6500K – 116 lm / W |
| This product contains a Light Source of Energy Efficiency Class F | |||
| Not suitable for accent lighting | |||
| CIRCULAR PRISMATIC | |||
| LED LAMP SPECIFICATIONS: | 9W | 14W | 18W |
| Luminaire lumens (with diffuser): Warm White, Cool White, Daylight White | 3000K – 1180 lm4400K – 1270 lm6500K – 1230 lm | 3000K – 1715 lm4400K – 1890 lm6500K – 1780 lm | 3000K – 2055 lm4400K – 2270 lm6500K – 2180 lm |
| Lumens from chip (array): Warm White, Cool White, Daylight White | 3000K – 1220 lm4400K – 1300 lm6500K – 1265 lm | 3000K – 1810 lm4400K – 1990 lm6500K – 1890 lm | 3000K – 2210 lm4400K – 2460 lm6500K – 2350 lm |
| Useful lumens (array): Warm White, Cool White, Daylight White | 3000K – 1140 lm4400K – 1225 lm6500K – 1190 lm | 3000K – 1630 lm4400K – 1790 lm6500K – 1690 lm | 3000K – 1950 lm4400K – 2160 lm6500K – 2070 lm |
| Rated Wattage | 9W | 14W | 18W |
| Rated luminous flux | 3000K – 1140 lm4400K – 1225 lm6500K – 1190 lm | 3000K – 1630 lm4400K – 1790 lm6500K – 1690 lm | 3000K – 1950 lm4400K – 2160 lm6500K – 2070 lm |
| Nominal life time of the lamp | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Colour temperature | 3000/4400/6500K | 3000/4400/6500K | 3000/4400/6500K |
| Number of switching cycles before premature lamp failure | ≥15000 | ≥15000 | ≥15000 |
| Warm-up time up to 60% of the full light output | Instant full light | Instant full light | Instant full light |
| Dimmable | No | No | No |
| Nominal beam angle | 120° | 120° | 120° |
| Rated power | 9W | 14W | 18W |
| Rated lamp lifetime | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Displacement factor | 0.97 | 0.97 | 0.97 |
| Lumen maintenance factor at end of nominal life | ≥80 | ≥80 | ≥80 |
| Starting time | Instant full light | Instant full light | Instant full light |
| Colour rendering | ≥0.8 | ≥0.8 | ≥0.8 |
| Colour consistency | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse |
| Rated peak intensity | 3000K – 398cd4400K – 428cd6500K – 415cd | 3000K – 570cd4400K – 627cd6500K – 592cd | 3000K – 683cd4400K – 754cd6500K – 722cd |
| Rated beam angle | 120° | 120° | 120° |
| Voltage / Frequency | 220-240V~50Hz | 220-240V~50Hz | 220-240V~50Hz |
| Lumen efficacy | 3000K – 131 lm / W4400K – 141 lm / W6500K – 137 lm / W | 3000K – 122 lm / W4400K – 135 lm / W6500K – 127 lm / W | 3000K – 114 lm / W4400K – 126 lm / W6500K – 121 lm / W |
| This product contains a Light Source of Energy Efficiency Class F | |||
| Not suitable for accent lighting | |||
| SQUARE OPAL | |||
| LED LAMP SPECIFICATIONS: | 9W | 14W | 18W |
| Luminaire lumens (with diffuser): Warm White, Cool White, Daylight White | 3000K – 1080 lm4400K – 1150 lm6500K – 1120 lm | 3000K – 1630 lm4400K – 1770 lm6500K – 1700 lm | 3000K – 1980 lm4400K – 2200 lm6500K – 2070 lm |
| Lumens from chip (array): Warm White, Cool White, Daylight White | 3000K – 1210 lm4400K – 1290 lm6500K – 1260 lm | 3000K – 1830 lm4400K – 1995 lm6500K – 1900 lm | 3000K – 2220 lm4400K – 2470 lm6500K – 2330 lm |
| Useful lumens (array): Warm White, Cool White, Daylight White | 3000K – 970 lm4400K – 1040 lm6500K – 1010 lm | 3000K – 1460 lm4400K – 1600 lm6500K – 1530 lm | 3000K – 1780 lm4400K – 1980 lm6500K – 1870 lm |
| Rated Wattage | 9W | 14W | 18W |
| Rated luminous flux | 3000K – 970 lm4400K – 1040 lm6500K – 1010 lm | 3000K – 1460 lm4400K – 1600 lm6500K – 1530 lm | 3000K – 1780 lm4400K – 1980 lm6500K – 1870 lm |
| Nominal life time of the lamp | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Colour temperature | 3000/4400/6500K | 3000/4400/6500K | 3000/4400/6500K |
| Number of switching cycles before premature lamp failure | ≥15000 | ≥15000 | ≥15000 |
| Warm-up time up to 60% of the full light output | Instant full light | Instant full light | Instant full light |
| Dimmable | No | No | No |
| Nominal beam angle | 120° | 120° | 120° |
| Rated power | 9W | 14W | 18W |
| Rated lamp lifetime | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Displacement factor | 0.97 | 0.97 | 0.97 |
| Lumen maintenance factor at end of nominal life | ≥80 | ≥80 | ≥80 |
| Starting time | Instant full light | Instant full light | Instant full light |
| Colour rendering | ≥0.8 | ≥0.8 | ≥0.8 |
| Colour consistency | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse |
| Rated peak intensity | 3000K – 223cd4400K – 239cd6500K – 223cd | 3000K – 338cd4400K – 368cd6500K – 353cd | 3000K – 411cd4400K – 456cd6500K – 432cd |
| Rated beam angle | 120° | 120° | 120° |
| Voltage / Frequency | 220-240V~50Hz | 220-240V~50Hz | 220-240V~50Hz |
| Lumen efficacy | 3000K – 120 lm / W4400K – 128 lm / W6500K – 124 lm / W | 3000K – 116 lm / W4400K – 126 lm / W6500K – 121 lm / W | 3000K – 110 lm / W4400K – 122 lm / W6500K – 115 lm / W |
| This product contains a Light Source of Energy Efficiency Class F | |||
| Not suitable for accent lighting | |||
| SQUARE PRISMATIC | |||
| LED LAMP SPECIFICATIONS: | 9W | 14W | 18W |
| Luminaire lumens (with diffuser): Warm White, Cool White, Daylight White | 3000K – 1150 lm4400K – 1250 lm6500K – 1200 lm | 3000K – 1730 lm4400K – 1870 lm6500K – 1830 lm | 3000K – 2100 lm4400K – 2360 lm6500K – 2200 lm |
| Lumens from chip (array): Warm White, Cool White, Daylight White | 3000K – 1200 lm4400K – 1300 lm6500K – 1260 lm | 3000K – 1830 lm4400K – 2000 lm6500K – 1910 lm | 3000K – 2220 lm4400K – 2470 lm6500K – 2330 lm |
| Useful lumens (array): Warm White, Cool White, Daylight White | 3000K – 1100 lm4400K – 1200 lm6500K – 1160 lm | 3000K – 1640 lm4400K – 1760 lm6500K – 1670 lm | 3000K – 2000 lm4400K – 2240 lm6500K – 2100 lm |
| Rated Wattage | 9W | 14W | 18W |
| Rated luminous flux | 3000K – 1100 lm4400K – 1200 lm6500K – 1160 lm | 3000K – 1640 lm4400K – 1760 lm6500K – 1670 lm | 3000K – 2000 lm4400K – 2240 lm6500K – 2100 lm |
| Nominal life time of the lamp | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Colour temperature | 3000/4400/6500K | 3000/4400/6500K | 3000/4400/6500K |
| Number of switching cycles before premature lamp failure | ≥15000 | ≥15000 | ≥15000 |
| Warm-up time up to 60% of the full light output | Instant full light | Instant full light | Instant full light |
| Dimmable | No | No | No |
| Nominal beam angle | 120° | 120° | 120° |
| Rated power | 9W | 14W | 18W |
| Rated lamp lifetime | 50,000 hrs | 50,000 hrs | 50,000 hrs |
| Displacement factor | 0.97 | 0.97 | 0.97 |
| Lumen maintenance factor at end of nominal life | ≥80 | ≥80 | ≥80 |
| Starting time | Instant full light | Instant full light | Instant full light |
| Colour rendering | ≥0.8 | ≥0.8 | ≥0.8 |
| Colour consistency | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse | Within 6 step Macadam ellipse |
| Rated peak intensity | 3000K – 425cd4400K – 459cd6500K – 447cd | 3000K – 628cd4400K – 675cd6500K – 640cd | 3000K – 767cd4400K – 860cd6500K – 805cd |
| Rated beam angle | 120° | 120° | 120° |
| Voltage / Frequency | 220-240V~50Hz | 220-240V~50Hz | 220-240V~50Hz |
| Lumen efficacy | 3000K – 128 lm / W4400K – 139 lm / W6500K – 133 lm / W | 3000K – 124 lm / W4400K – 134 lm / W6500K – 131 lm / W | 3000K – 117 lm / W4400K – 131 lm / W6500K – 122 lm / W |
| This product contains a Light Source of Energy Efficiency Class E | |||
| Not suitable for accent lighting | |||
Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Visit our website: www.eterna-lighting.co.uk
Issue 0122
Made in China
Documents / Resources
 |
Eterna PRSQMW Power and Colour Temperature Selectable IP65 LED Utility Fitting with Multi-Function Sensor [pdf] Instruction Manual PRSQMW, PRCIRMW, OPSQMW, OPCIRMW, PRSQMW Power and Colour Temperature Selectable IP65 LED Utility Fitting with Multi-Function Sensor, PRSQMW, Power and Colour Temperature Selectable IP65 LED Utility Fitting with Multi-Function Sensor, Power and Colour Temperature Selectable IP65 LED Utility Fitting, Selectable IP65 LED Utility Fitting, Utility Fitting |
