BrainChild QS0MCT1A MCT Controller Multi Loop
Specifications
- Model: MCT Ver: QS0MCT1A
- Tîp: 1/4 DIN Kontrolkerê Pir-Loop
- Navber: Ekrana Têkilî
Talîmatên Bikaranîna Product
Install Process Control/Limit Modules
- Select a slot for the module and remove the empty slot cover.
- Guhestina DIP-ê li ser modulê ji bo celebê têketina pêdivî bicîh bikin.
- Insert the module into the slot and secure it in place using retention screws.
Sazkirin û Çêkirin
- Cut a proper size opening in the panel and insert the MCT controller through the front panel cutout.
- Insert curved tab of retention brackets into notches in the MCT and tighten screws evenly to secure it in place.
Têkilî û Têlkirin
- Connect input/output wiring to the installed PCM/HLM modules following the connection diagrams provided.
- Connect the MCT to a network or PC via its serial communication interface (optional).
Configure The MCT For Use
Switch between Operation/Configuration Modes as needed to set up and configure the MCT for use.
MCT – 1/4 DIN Multi-Loop Controller A 1/4 DIN multi-loop controller that operates like your favorite smartphone or tablet
Bikaranîna Hêsan Navbera ekrana Têkilî
- Gavên di vê rêbernameya destpêka bilez de bişopînin da ku saz bikin û dest bi karanîna kontrola MCT-ya xwe bikin.
Hardware Recommended
ToolsHardware Recommended Tools
- Hardware
- PCM (process control module)
- Note: at least 1 required
- HLM (high limit module)
- Note: optional
Perçê pêva
- Retention bracket for mounting
Amûrên
- Screwdriver Phillips biçûk
- Screwdriver biçûk
- Wire and wire stripper (maximum 14awg)
Lêkirinî
Install Process Control/ Limit Modules
- A. Select a slot for the module.
- B. Loosen screws; remove empty slot cover
- C. Set DIP switch on module for required input type.
- HLM 0-1V and 0-5V/1-5V input types are special order. HLMs ordered with either input type cannot be configured or programmed for any other type.
- D. Insert module into slot while observing card orientation and secure module in place using retention screws from slot cover.
Installation and Moniting
- A. Cut proper size opening in panel.
- B. Insert MCT controller through front panel cutout.
- C. Insert curved tab of retention brackets(C) into notches in the top, bottom and sides of the MCT(B) and tighten screws evenly in order to secure the MCT in place.
Girêdan û Têlkirin
- A. Connect power using 14 AWG copper conductors rated for mini mum 90°C.To make a connection, strip ¼” of insulation off the end of the wire, turn the connector screw counter-clockwise until the gap is wide open, insert the wire all the way in, and turn the screw clockwise until it’s tight (maximum torque rating = 0.51 N-m).
- B. Input/output control wiring: Connect input/output wiring to the installed PCM/HLM modules. PCM connection diagram provided on left side of MCT. HLM connection diagram provided on right side of MCT.
- C. Communication interfaces: Connect the MCT to a network and or PC via its serial communication interface (optional).
Not:
- Dengê bilindtage units (90 to 250 VAC) are equipped with an orange power connector. Low voltage units (11 to 26 VAC/DC) are equipped with a green power connector.
Not:
- A communication connection is not required to set up or use your MCT.
Not:
- Removable connectors make wiring easy. Remove the connector, attach your wires and simply plug it back in.
Not:
- Upon application of power, if the MCT does not come on within 2 seconds, remove power. Check wiring to insure proper connections and try to power up again. An Internal fuse will prevent damage for over-voltagşert û mercên; Lêbelê, ew ne garantî ye.
Configure The MCT For Use
4-1 Switch between Operation/ Configuration Modes
- Configuration mode supports English interface only
- Operating mode supports multi-language. To change language, go to Configuration mode > Offline setting.
To turn off data recording
- Apply main power to the MCT and allow the unit to start up (Image A).
- Rojnamevanî
the menu icon and select Data > Data (Image a/b). Turn off the green light on the upper-right corner. Press homepage 
the home icon to exit to (Image b).
To enter the Offline setting:
- Press the menu icon to access and select Device > Settings (Image c).
Ji bo guhertina navbeynkariya ziman:
- In offline mode, again press the Menu and select Set > Language (Image e). Choose your desired language to ON. Tap <Save> (Image f). Tap <OK> at the prompt.
- Rojnamevanî the menu icon > System to continue offline setting (Image G) or
- çap bike home icon to exit to operation Home. (Image A).
Configure parameters of the controller:
To configure the unit manually:
- In offline mode, press the menu icon and select ‘Exit’ from the ‘System’ menu (Image G). *Menu> System > Exit
- On the Exit Application screen press the second choice ‘Exit application.
(configuration mode startup)‘ button to quit the runtime (Image H). Tap <Yes> at the prompt to exit to reboot into the Configurator application.(Image B)
- Begin by pressing the menu icon and select ‘Control Setup’ from the ‘Setup’ menu. Set the control type according to the installed PCMs/ HLMs (Image I) * Configuration mode supports English interface only
- Once the control type is set, navigate to the Loop Configuration by selecting it from the ‘Setup’ menu (Image J/ K). * Menu > Setup > Loop Configuration
- Configure the loop by selecting the various settings form the list and entering the required values (Image L).
- Continue the process for other loops and limit (if installed). (Image M)
- Personalize the interface by removing features not required by selecting ‘Functions’ from the ‘Startup’ menu and turning the required options on or off. (Image N) *Menu > Startup > Functions
- Once all settings have been completed, select ‘Exit” from the ‘File’ menu. (Image O). Once the Configurator window has been closed, cycle power to the MCT to complete the configuration process. (Image P)
Auto configure parameters by importing files
Ji bo împortkirina veavakirina heyî file:
Follow steps 1-2. Cycle power to the MCT to operation mode. (P)
- Press the menu icon and select Data > Data (Image Q). Turn off the green light on the upper-right corner. Press the Home to exit. (Image R)
- Press the menu icon and select Device > Settings (Image S). Press the menu icon again and select Offline > Offline (Image T). Tap <Yes>.
- In offline mode, press the menu icon > System > Configuration (U).
- To import a configuration from a USB memory stick, first insert the USB memory device containing the desired configuration file di porta USB ya MCT de. (Wêne V)
- Press the ‘Load Configuration’ file bişkojka, ya xwestî veke file and allow cthe configuration to load (Image V/ W).
- Once the import is completed, cycle power to the MCT to complete the configuration process. (Image X)
| File | |
| 1 Derî | 3 Loop Navnîşan Utility |
| 2 Ji dor | 4 Zîrek IO Comms Utility |
| Damezirandin | |
| 1 Kontrol Damezirandin | |
| Soft Alarms, Monitor Points, Math/Logic, Outputs Off on Input Error | |
| 2. Loop Veavakirin | |
| 2.1 TagNav | 2.21 Derketin 4 Fonksiyon |
| 2.2 Type Input | 2.22 Derketin 4 Veguheztina têkçûn |
| 2.3 Yekîneyên Input | 2.23 Derketin 4 Nirxên Sînorê Kêm / Bilind |
| 2.4 Xala Dehanî | 2.24 Derketin 4 Pîvana Kêm / Bilind Ji nû ve veguhezîne |
| 2.5 Input Kêm / Pîvana Bilind | 2.25 Alarm (1-3) Fonksiyon |
| 2.6 Parzûna Input | 2.26 Alarm (1-3) Mode |
| 2.7 Fonksiyon Input Bûyer | 2.27 Alarm (1-3) Nîşan |
| 2.8 Peyama Alarm Ketina Bûyerê / Şîrovekirin | 2.28 Alarm (1-3) Nîqaşa danînê |
| 2.9 Kêm / Bilind Sînora Setpoint | 2.29 Alarm (1-3) Hysteresis |
| 2.10 Derketin 1 Fonksiyon | 2.30 Alarm (1-3) Dereng |
| 2.11 Derketin 1 Veguheztina têkçûn | 2.31 Di Destpêka Bernameya Xweser de xala danînê |
| 2.12 Output 1 ON-OFF Control Hysteresis | 2.32 Di dawiya Bernameya Otomatîk de xala danînê |
| 2.13 Derketin 1 Dema Cycle | 2.33 Desthilatdariya Têkçûna Hêzê |
| 2.14 Derketin 1 Nirxên Sînorê Kêm / Bilind | 2.34 Moda Ragihandinê |
| 2.15 Derketin 2 Fonksiyon | 2.35 Mode Loop |
| 2.16 Derketin 2 Veguheztina têkçûn | 2.36 Ramp Rate Operasyona |
| 2.17 Derketin 2 Dema Cycle | 2.37 Ramp Rêjeya Down Low / Sînora Jor |
| 2.18 Derketin 2 Nirxên Sînorê Kêm / Bilind | 2.38 Ramp Rêjeya Hilkişîna Kêm / Sînorê Jorîn |
| 2.19 Derketin 3 Fonksiyon | 2.39 Setpoint 2 Format |
| 2.20 Derketin 3 Veguheztina têkçûn | 2.40 Nîqaşa danînê 2 |
| 3. Limit Configuration | |
| 3.1 TagNav | 3.12 Derketin 2 Fonksiyon |
| 3.2 Type Input | 3.13 Fonksiyon Alarm |
| 3.3 Yekîneyên Input | 3.14 Moda Alarm |
| 3.4 Xala Dehanî | 3.15 Nîşana Alarm |
| 3.5 Ketina Kêm / Pîvana Bilind | 3.16 Nîşaneya Alarmê |
| 3.6 Parzûna Input | 3.17 Alarm Hysteresis |
| 3.7 Derketin 1 Fonksiyon | 3.18 Veguheztina têkçûna alarmê |
| 3.8 Derketin 1 Hysteresis | 3.19 Fonksiyon Input Bûyer |
| 3.9 Jêrîn / Sînorê Jorîn a Pîvana Bilind | 3.20 Forma Nîşandanê |
| 3.10 Jêrîn / Sînorê Jorîn ê Niqteya Mîhengê ya Kêm | 3.21 Moda Ji nû ve destpêkirinê |
| 3.11 Niqteya danîna sînorên bilind / nizm | |
| 4 Çavdêr Veavakirin | |
| 4.1 Tagnav | 4.4 Xala Dehanî |
| 4.2 Type Input | 4.5 Input Kêm / Pîvana Bilind |
| 4.3 Yekîneyên Input | |
| 5 Nerm Hawar Veavakirin | |
| Çavkaniya alarmê, Cureya alarmê, Astengkirin, Bêdeng, E-name, Zengvegera, Nîqaşa Alarmê, Hysteresis, Dereng | |
| 6 Math/Logic Configuration | |
| 6.1 Ketina Wekheviyek Math/Logic | 6.2 Wekheviya Math / Logic Examples |
| Vebijêrk | |
| 1 Kaskad Kontrol | |
| Astengdar, Pêvajo, Deviasyon, Rêje | |
| 2 Berfirehkirin IO | |
| 2.1 Input (8-23) Function | 2.3 Input Kêm / Pîvana Bilind |
| 2.2 Input (8-23) Alarm Message/Annotation | |
| 3 Demjimêra bûyerê | |
| Vebijarka demjimêra bûyerê, moda têkçûna hêzê, Alarm li ser qedandinê, E-name/SMS li ser qedandinê | |
| Damezirandin | |
| 1 Functions | 2 Destpêk View |
| Tagnavên | |
| 1 alarm Nav | 3 Custom Name\ Navnîşan |
| 2 Event Navên | |
bêtir agahdarî
assistance contact Tech Support:
- service@brainchild.com.tw
- 886-2-2786-1299
- http://www.brainchildtw.com
FAQ
- Pirs: Ma ez pêwendiyek pêwendiyê hewce dikim ku MCT bikar bînim?
- A: No, a communication connection is not required to set up or use your MCT.
- Pirs: Ger MCT hêz neke divê ez çi bikim?
- A: If the MCT does not come on within 2 seconds of applying power, remove power, check wiring for proper connections, and try powering up again. An internal fuse will prevent damage for overvoltagşert û mercên.
Belge / Çavkanî
 |
BrainChild QS0MCT1A MCT Controller Multi Loop [pdf] Rehbera bikaranînê QS0MCT1A MCT Kontrolkerê Pir Loopê, QS0MCT1A, Kontrolkerê Pir Loopê MCT, Kontrolkerê Pir Loopê, Kontrolkerê Loopê |
