Eldri DSP Wavelaunch örgjörvi

Notkunarleiðbeiningar fyrir vöru

• The high definition Digital Wavelaunch Processor hosts a LEGACY custom algorithm that automatically loads when the processor is powered on.
• Factory settings are ‘plug and play’ and do not require a computer to utilize. Connections between the preamp, kraftur amphátalara og hátalara/subbassahátalara er að finna með hátalarunum/subbassahátalaranum þínum.
• Attach the included IEC power cable to the rear of the unit, and flip the rear power switch by pushing. The front panel will load and display the name of the currently selected algorithm next to Scene.
• It is okay to leave the Wavelaunch processor on 24/7 as it draws minimal power.
• Hægt er að snúa gagnahjólinu til vinstri/hægri til að auka/minnka gildi blikkandi breytunnar á skjánum. Með því að ýta á gagnahjólið verður gildið slegið inn og bendilinn færður á næstu breytu.
• Wavelaunch provides parametric EQ options to further adjust Legacy speakers/subwoofers. Here’s how to adjust the EQ of the left Aeris XD speaker:
• Press the PEQ button located on the left of the front panel.
• Note the input channels A-D, with A corresponding to the left signal and B to the right signal from your preamplifier/surround processor.
• Ýttu á inntakshnappinn A.
• Rotate the rotary dial left/right to the desired setting. Press the dial in to progress to the next setting.
• Repeat steps for input B if applying adjustments to the right Aeris XD speaker.
• Press the data wheel again to exit once adjustments are done.

Fljótleg uppsetning

• The high definition Digital Wavelaunch Processor hosts a LEGACY custom algorithm that automatically loads when the processor is powered on.
• Factory settings are ‘plug and play’, and do not require a computer to utilize.
• Connections between the preamp, kraftur amphátalara og hátalara/subbassahátalara er að finna með hátalarunum/subbassahátalaranum þínum.

Kveikir á

• Attach the included IEC power cable to the rear of the unit, and flip the rear power switch by pushing I.
• The front panel will load and display the name of the currently selected algorithm next to “Scene”.
• Það er í lagi að láta Wavelaunch örgjörvann vera í gangi allan sólarhringinn þar sem hann notar lágmarksorku.

Að auka/minnka hljóðstyrk eldri hátalara/bassahátalara
Hægt er að snúa gagnahjólinu til vinstri/hægri til að auka/minnka gildi blikkandi breytunnar á skjánum. Með því að ýta á gagnahjólið verður gildið slegið inn og bendilinn færður á næstu breytu.
Notum Legacy Aeris XD fyrir þetta dæmi.ampog gerum ráð fyrir að þú viljir auka hljóðstyrkinn (gain) í Aeris bassahlutanum.

1. Press the “Gain” button located at the left of the front panel.
2. Please note the 8 output channels at the far right of the front panel, labeled 1-8. Output channel 1 corresponds to the left Aeris active bass channel, and output channel 5 corresponds to the right Aeris active bass channel. Output 2 corresponds to the left Aeris upper section, and Output 6 corresponds to the right Aeris upper section, powered by your stereo amplíflegri.
3. Press the output “1” button.
4. The screen will update, and you will see a dB gain level- please rotate the rotary dial to the right to increase the volume level of the left bass section. Once the desired bass output on the left side is achieved, you can press the output “5” button and increase the volume level of the right bass section to the desired level.
5. Once you are done with adjustments, you can press the data wheel again to exit.

Að gera jöfnunarstillingar
Wavelaunch provides the user with parametric EQ options to further adjust your Legacy speakers/subwoofers.
Notum Legacy Aeris XD fyrir þetta dæmi.ampSvona stillirðu EQ á vinstri Aeris XD hátalaranum.

1. Press the “PEQ” button located at the left of the front panel.
2. Please note the 4 input channels at the right of the front panel, labeled A-D. Input channel A corresponds to the left signal, and channel B corresponds to the right signal from your preamplifier/surround processor.
3. Press the input “A” button.
4. The screen will update and you can rotate the rotary dial left/right to the desired setting. You can press the dial in to progress to the next setting.
5. Repeat these steps for input “B” if you would like to apply the same PEQ adjustments to the right Aeris XD speaker.
6. Once you are done with adjustments, you can press the data wheel again to exit.

Tengingar

• A connection assignment printout is also included with your speaker/subwoofer to assist you in getting started.

Wavelaunch Processor Inputs

• Labeled A, B, C, D
• Typical speaker Assignments are A left signal, B right signal
• Please consult your speakers/subwoofers diagram for specific connections.

Wavelaunch Processor Outputs

• Labeled, 1, 2, 3, 4, 5, 6, 7, 8
• Typical speaker assignments are outputs 1-4 left signal, and outputs 5-8 right signal.
• Til dæmisample, Aeris XD assignments Output channel 1 corresponds to the left Aeris active bass channel, and output channel 5 corresponds to the right Aeris active bass channel. Output 2 corresponds to the left Aeris upper section and Output 6 corresponds to the right Aeris upper section, powered by your stereo amplíflegri.

Wavelaunch fylgihlutir

• Inside the Wavelaunch processor carton packaging, you’ll find the included IEC power cable.

Tæknilýsing

• Processor (DSP): 32-Bit Floating Point
• Analog Converters: Super Performance 24-bit
• Fjöldi verkefna: 64
• Parametric EQ: 16 per channel
• Filters: Butterworth, Linkwitz-Riley & Bessel
• Connectors: 4 XLR In, 8 XLR Out, USB Type B
• Dynamic Range: 115 dB (unweighted)
• Distortion: ≤0.0025% @ 4dBu 20Hz-20KHz
• Frequency Response (Hz, +/- .1 dB): 20 to 20 kHz
• Mál (HxBxD, tommur): 2.6 x 19 x 10.6
• Þyngd: 7 lbs
• Samplanghraði: 96 kHz

Ábyrgð

Legacy Audio supports its customers and products with pride. We cheerfully warrant our processors from defects in materials and workmanship for three (3) years. Please register your product with Legacy Audio. Should you require service, Legacy will require proof of purchase to honor the warranty, so please keep your receipt.

• Ábyrgðin gildir fyrir upprunalega eigandann og er ekki framseljanleg.
• Ábyrgðin á við um vörur sem keyptar eru frá „viðurkenndum söluaðila“.
• Ábyrgðin á virkum íhlutum eins og stafrænum örgjörvum eða innri amplifers takmarkast við þriggja (3) ára tryggingu.
• Ábyrgðin á birgðum söluaðila nær að hámarki í tvö ár frá reikningi.
• Ábyrgðin nær ekki til flutningskostnaðar vöru til eða frá viðskiptavinum, dreifingaraðila eða söluaðila, eða tengdum sendingartjóni.
• Eftirfarandi aðstæður eða skilyrði falla ekki undir Legacy Audio ábyrgð:
• Accidental damage, electrical abuse or associated equipment failure
• Use is inconsistent with the recommended operating instructions and specifications
• Tjón af völdum breytinga eða óviðkomandi þjónustu
• Kostnaður við að fjarlægja og setja upp gallaðar vörur. Afleidd skemmdir á öðrum vörum.
• Normal wear, such as fading of finishes due to sunlight.

Umhyggja

• If you wish to clean your Wavelaunch, use a diluted ammonia-based window cleaner.
• Do not use any abrasive cleaners or chemical solvents.

Do not block any ventilation openings. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat. The power cable should be unplugged from the outlet during severe electrical storms or when unused for a long time. Grounding: Adequate precautions should be taken so that the grounding provisions built into an electrical product are never defeated.
All information contained in this manual is accurate to the best of our knowledge at the time of publication. In keeping with our policy of ongoing product improvement, we reserve the right to make changes to the design and features of our products without prior notice. A listing of Legacy Audio Dealers and Distributors can be found on the Legacy Audio websíða www.legacyaudio.com or by contacting Legacy Audio at: 3023 E. Sangamon Ave., Springfield, IL 62702, USA—Phone: +1 217-544-3178.

Hafðu samband

• ©2025 Legacy Audio
• 3023 E Sangamon Ave.
• Springfield, IL 62702
• Sími: 800-283-4644
• Fax: 217-544-1483

Algengar spurningar

• What are the differences between the included Legacy Wavelaunch processor and the upgraded Legacy Wavelet 2 processor?
  • There are quite a few technical differences between the two. The Wavelet 2 processes at 64 bits and has a more advanced correction algorithm. Most importantly, the Wavelet 2 also corrects in the time domain, while the
  • Wavelaunch is largely correcting only in the frequency domain.
  • Additionally, Wavelet 2 can also be used as a preampléttari (foramp can be bypassed), and includes its own microphone to automatically run room correction and adjust for the room. Wavelet 2 also features a high-end DAC, capable of up to 32 bit 384kHz audio, in addition to accommodating 4 other analog stereo sources and 4 digital inputs.
  • Finally, Wavelet 2 is also easier to control, wirelessly from any iPad/iPhone/Android or computer.
  • For full information, please see more here.

Skjöl / auðlindir

Eldri DSP Wavelaunch örgjörvi [pdf] Handbók eiganda 2025, DSP Wavelaunch örgjörvi, DSP, Wavelaunch örgjörvi, örgjörvi

Heimildir

• Notendahandbók