DSP Wavelaunch-verwerker
“
Spesifikasies
- Product Name: Legacy Wavelaunch
- Processor Type: Digital Wavelaunch Processor
- Algorithm: LEGACY custom algorithm
- Power Source: IEC power cable
- Power Consumption: Minimal power draw
Produkgebruiksinstruksies
Vinnige opstelling
The high definition Digital Wavelaunch Processor hosts a LEGACY
custom algorithm which automatically loads when the processor is
powered on. Factory settings are ‘plug and play’ and do not require
a computer to utilize. Connections between the preamp, krag
amplifier, and speakers/subwoofer can be found with your
speakers/subwoofer.
Skakel aan
Attach the included IEC power cable to the rear of the unit, and
flip the rear power switch by pushing I. The front panel will load
and display the name of the currently selected algorithm next to
Toneel.
It is okay to leave the Wavelaunch processor on 24/7 as it draws
minimal power.
Volume aanpassing
The data wheel can be turned left/right to increase/decrease the
value of the flashing parameter on the screen. Pressing the data
wheel in will enter the value and move the cursor to the next
parameter.
Making EQ Adjustments
Wavelaunch provides parametric EQ options to further adjust
Legacy speakers/subwoofers. Here’s how to adjust the EQ of the left
Aeris XD speaker:
- Press the PEQ button located at the left of the front
paneel. - Note the input channels A-D, with A corresponding to the left
signal and B to the right signal from your preamplifier/surround
verwerker. - Press input A button.
- Rotate the rotary dial left/right to the desired setting. Press
the dial in to progress to the next setting. - Repeat steps for input B if applying adjustments to the right
Aeris XD speaker. - Press the data wheel again to exit once adjustments are
gedoen.
Verbindings
A connections assignment printout is included with your
speaker/subwoofer to assist you in getting started.
Wavelaunch Accessories
Included in the Wavelaunch processor carton packaging is the IEC
kragkabel.
Gereelde vrae
Q: Can I adjust EQ settings for individual
speakers/subwoofers?
A: Yes, the Wavelaunch processor allows you to make parametric
EQ adjustments for each speaker/subwoofer individually. Follow the
provided instructions for making EQ adjustments.
"`
Legacy Wavelaunch
Eienaarshandleiding
Inhoudsopgawe
Quick Setup ………………………………………………………………………………………………………………………………………………………………….. 3
Powering on ……………………………………………………………………………………………………………………………………………………………………………………………………. 3 Increasing/Decreasing the Volume of Legacy Audio Speakers/Subwoofers…………………………………………………………………………………………………………………..3 Making EQ Adjustments……………………………………………………………………………………………………………………………………………………………………………………..4
Connections ………………………………………………………………………………………………………………………………………………………………….. 5
Wavelaunch Processor Inputs………………………………………………………………………………………………………………………………………………………………………………5 Wavelaunch Processor Outputs……………………………………………………………………………………………………………………………………………………………………………5
Wavelaunch Accessories ………………………………………………………………………………………………………………………………………………… 6 Specifications ……………………………………………………………………………………………………………………………………………………………….. 6 FAQ……………………………………………………………………………………………………………………………………………………………………………… 7 Warranty ……………………………………………………………………………………………………………………………………………………………………… 8 Care …………………………………………………………………………………………………………………………………………………………………………….. 9
2
Vinnige opstelling
The high definition Digital Wavelaunch Processor hosts a LEGACY custom algorithm which automatically loads when the processor is powered on. Factory settings are `plug and play’, and do not require a computer to utilize. Connections between the preamp, krag amplifier, and speakers/subwoofer can be found with your speakers/subwoofer.
Skakel aan
Attach the included IEC power cable to the rear of the unit, and flip the rear power switch by pushing I. The front panel will load and display the name of the currently selected algorithm next to “Scene”.
It is ok to leave the Wavelaunch processor on 24/7 as it draws minimal power.
Increasing/Decreasing the Volume of Legacy Audio Speakers/Subwoofers
The data wheel can be turned left/right to increase/decrease the value of the flashing parameter on the screen. Pressing the data wheel in will enter the value and move the cursor to the next parameter.
Let’s use the Legacy Aeris XD for this example, and let’s assume you would like to increase the volume (gain) of the Aeris bass section.
1. Press the “Gain” button located at the left of the front panel. 2. Please note the 8 output channels at the far right of the front panel, labeled 1-8. Output channel 1 corresponds to the left Aeris active bass channel, and output channel 5 corresponds to the right Aeris active bass channel. Output 2 corresponds to the left Aeris upper section and Output 6 corresponds to the right Aeris upper section powered by your stereo amplifier. 3. Press the output “1” button. 4. The screen will update and you will see a dB gain level- please rotate the rotary dial to the right to increase the volume level of the left bass section. Once the desired bass output on the left side is achieved, you can press the output “5” button and increase the volume level of the right bass section to the desired level. 5. Once you are done with adjustments, you can press the data wheel again to exit.
3
Making EQ Adjustments Wavelaunch provides the user with parametric EQ options to further adjust your Legacy speakers/subwoofers. Let’s use the Legacy Aeris XD for this example. Here’s how to adjust the EQ of the left Aeris XD speaker.
1. Press the “PEQ” button located at the left of the front panel. 2. Please note the 4 input channels at the right of the front panel, labeled A-D. Input channel A corresponds to the left signal, and
channel B corresponds to the right signal from your preamplifier/surround processor. 3. Press the input “A” button. 4. The screen will update and you can rotate the rotary dial left/right to the desired setting. You can press the dial in to progress to
the next setting. 5. Repeat these steps for input “B” if you would like to apply the same PEQ adjustments to the right Aeris XD speaker. 6. Once you are done with adjustments, you can press the data wheel again to exit.
4
Verbindings
A connections assignment printout is also included with your speaker/subwoofer to assist you in getting started.
Wavelaunch Processor Inputs Labeled A, B, C, D Typical speaker Assignments are A left signal, B right signal Please consult your speakers/subwoofers diagram for specific connections. Wavelaunch Processor Outputs Labeled, 1, 2, 3, 4, 5, 6, 7, 8 Typical speaker assignments are outputs 1-4 left signal, and outputs 5-8 right signal. For example, Aeris XD assignments Output channel 1 corresponds to the left Aeris active bass channel, and output channel 5 corresponds to the right Aeris active bass channel. Output 2 corresponds to the left Aeris upper section and Output 6 corresponds to the right Aeris upper sections, powered by your stereo amplewendiger.
5
Wavelaunch Accessories
Inside the Wavelaunch processor carton packaging you’ll find the included IEC power cable.
Spesifikasies
· Processor (DSP):32-Bit Floating Point · Analog Converters: Super Performance 24-bit · No. of Programs:64 · Parametric EQ:16 per channel · Filters: Butterworth, Linkwitz-Riley & Bessel · Connectors: 4 XLR In, 8 XLR Out, USB Type B · Dynamic Range: 115 dB (unweighted) · Distortion: 0.0025% @ 4dBu 20Hz-20KHz · Frequency Response (Hz, +/- .1 dB): 20 to 20 kHz · Dimensions (HxWxD, inches): 2.6 x 19 x 10.6 · Weight: 7 lbs · Samplingsnelheid: 96 kHz
6
Gereelde vrae
What are the differences between the included Legacy Wavelaunch processor and the upgrade Legacy Wavelet 2 processor? There are quite a few technical differences between the two. The Wavelet 2 processes at 64 bits, and has a more advanced correction algorithm. Most importantly, the Wavelet 2 also corrects in the time domain, while the Wavelaunch is largely correcting only in the frequency domain. Additionally, Wavelet 2 can also be used as a preamplifier (the preamp can be bypassed), and includes its own microphone to automatically run room correction and adjust for the room. Wavelet 2 also features a high-end DAC, capable of up to 32 bit 384kHz audio, in addition to accommodating 4 other analog stereo sources and 4 digital inputs. Finally, Wavelet 2 is also easier to control, wirelessly from any iPad/iPhone/Android or computer. For full information, please see more, here.
7
Waarborg
Legacy Audio supports its customers and products with pride. We cheerfully warrant our processors from defects in materials and workmanship for a period of three (3) years. Please register your product with Legacy Audio. Should you require service Legacy will require a proof of purchase in order to honor the warranty – so please keep your receipt. The warranty applies to the original owner and is not transferable. The warranty applies to products purchased from an “Authorized Legacy Dealer”. The warranty on active components such as digital processors or internal amplifiers is limited to three (3) years of coverage. The warranty on dealer stock will extend for a maximum of two years from invoice. The warranty does not cover transportation costs of product to or from the customer, distributor or dealer, or related shipping damage. The following situations or conditions are not covered by the Legacy Audio warranty: Accidental damage, electrical abuse or associated equipment failure Use inconsistent with recommended operating instructions and specifications Damage caused by modification or unauthorized service Costs associated with the removal and reinstallation of defective products. Consequential damage to other products. Normal wear such as fading of finishes due to sunlight.
8
Omgee
If you wish to clean your Wavelaunch, use a diluted ammonia based window cleaner. Do not use any abrasive cleaners or chemical solvents.
9
Moenie enige ventilasie-openinge blokkeer nie. Moenie naby enige hittebronne soos verkoelers, hitteregisters, stowe of ander apparaat wat hitte produseer installeer nie. Die kragkabel moet tydens erge elektriese storms of wanneer dit vir 'n lang tydperk ongebruik word van die uitlaat afgetrek word. Aarding: Voldoende voorsorgmaatreëls moet getref word sodat die aardingsvoorsiening wat in 'n elektriese produk ingebou is, nooit vernietig word nie.
Al die inligting wat in hierdie handleiding vervat word, is na ons beste wete akkuraat ten tye van die publikasie. In ooreenstemming met ons beleid van voortgesette produkverbetering, behou ons ons die reg voor om veranderinge aan te bring in die ontwerp en funksies van ons produkte sonder vooraf kennisgewing.
'n Lys van Legacy Audio-handelaars en -verspreiders kan op die Legacy Audio gevind word website www.legacyaudio.com or by contacting Legacy Audio at: 3023 E. Sangamon Ave., Springfield, IL 62702, USA–Phone: +1 217-544-3178.
10
©2025 Legacy Audio 3023 E Sangamon Laan. Springfield, IL 62702 Telefoon: 800-283-4644
Faks: 217-544-1483
11
Dokumente / Hulpbronne
 |
Legacy DSP Wavelaunch Processor [pdf] Eienaar se Handleiding 2025, DSP Wavelaunch Processor, DSP, Wavelaunch Processor, Processor |