GODIAG GT115 For V-A-G MQB IMMO4
CAN-Bus UDS 4th Generation IMMO
System Test Platform
Notendahandbók
202506
Vara lokiðview
MQB models may range from superminis to large family cars, replacing the current generations of models. The MQB architecture replaces the PQ25, PQ35 and PQ46 platforms. Our product is a connecting cable designed for the MQB IMMO system, enabling engineers to conveniently perform off-vehicle operations such as IMMO programming, matching, and diagnostics on the MQB IMMO system.
Moreover, it has a POGO PIN to read and write data to the dashboard, which is more stable to hold and does not damage the cable.
Aðgerðir:
- Synchronous detection of key and vehicle IMMO module
- Independent diagnosis of engine and power expansion module.
- Communication diagnosis and programming test of engine module and power module through gateway module
- IMMO 4th generation POGO PIN read and write data and key synchronization detection
- Connect BCM module with gateway module for communication diagnosis and programming test(Note: Press the corresponding switch when required.)
- Gateway module detection
- Current connected power supply voltage sýna
- Current connected module current display
- 2032 battery voltage uppgötvun.
- With POGO PIN to read and write data to the dashboard.
Skref til að greina lykla með því að nota IMMO 4 CAN-BUS UDS kerfið
Skref 1: Connect the GT115 to the dashboard and connect it to the power supply.
Skref 2: Press the start button, press the ignition button, and then press the Dash button.
Skref 3: The instrument panel displays safe, and the key sensor coil flashes for 3 seconds and then goes out. It indicates that the key is not recognized.
Skref 4: Connect the GT115 to the dashboard and connect it to the power supply.
Skref 5: Press the start button, press the ignition button, and then press the Dash button.
Skref 6: The instrument panel displays the mileage, and the key sensor coil flashes and then goes out. It indicates that the key has been identified.
Skref til að nota POGO PIN á IMMO 4 CAN-BUS UDS palli
Skref 1: Connect GT115 to the instrument panel and power it on.
Skref 2: First press the red ignition button, then press the “Dash” button
Skref 3: Then use the pogo pin probe to poke the pogo pin point in the instrument chip.
Skref 4: After poking, do not let go and press the start button again.
Skref 5: Wait for 5 seconds and then release the pogo pin probe.
Skref 6: At this time, only one light is on, indicating that the instrument has successfully entered the pogo pin mode.
Skref til notkunar á MQB kerfinu
Skref 1: Connect the gateway.
Skref 2: Connect the BCM module.
Skref 3: Connect the instrument.
Skref 4: Connect the engine.
Skref 5: Finally, turn on the power.
Skref 6: Press the start button and the red ignition switch button again.
Skref 7: Then you can connect other devices for testing, diagnoses, programming and coding.
Skref til að nota vélóháð samskipti
Skref 1: Connect the engine with colored jumper wires.
Skref 2: Tengdu við rafmagn.
Skref 3: Press in sequence: power switch start, ignition switch IGN, engine button switch ENG.
Skref 4: Then connect other devices to the OBD port for testing and diagnosis.
Aukabúnaður:
1 stk x GT115 MQB IMMO4 CAN-Bus UDS 4. kynslóðar IMMO kerfisprófunarpallur 1 stk x PDF handbók
Shenzhen Sinoy Technology Co., Ltd
Allur réttur áskilinn
www.godiag.com
+86 18813687743
Sales@GoDiag.com
https://h5.shengcai.net/wwei/url?url=H666G_0Kx6G
Takk fyrir að lesa!
Skjöl / auðlindir
 |
GODIAG GT115 IMMO4 CAN Bus UDS prófunarpallur [pdfNotendahandbók GT115, GT115 IMMO4 CAN Bus UDS prófunarpallur, GT115, IMMO4 CAN Bus UDS prófunarpallur, UDS prófunarpallur, Prófunarpallur, Pallur |