GODIAG GT115 For V-A-G MQB IMMO4
CAN-Bus UDS 4th Generation IMMO
System Test Platformየተጠቃሚ መመሪያ
202506

ምርት አልቋልview

MQB models may range from superminis to large family cars, replacing the current generations of models. The MQB architecture replaces the PQ25, PQ35 and PQ46 platforms. Our product is a connecting cable designed for the MQB IMMO system, enabling engineers to conveniently perform off-vehicle operations such as IMMO programming, matching, and diagnostics on the MQB IMMO system.
Moreover, it has a POGO PIN to read and write data to the dashboard, which is more stable to hold and does not damage the cable.

ተግባራት፡-

1. Synchronous detection of key and vehicle IMMO module
2. Independent diagnosis of engine and power expansion module.
3.  Communication diagnosis and programming test of engine module and power module through gateway module
4.  IMMO 4th generation POGO PIN read and write data and key synchronization detection
5. Connect BCM module with gateway module for communication diagnosis and programming test(Note: Press the corresponding switch when required.)
6. Gateway module detection
7. Current connected power supply voltagሠ ማሳያ
8. Current connected module current display
9. 2032 battery voltagሠ መለየት።
10.  With POGO PIN to read and write data to the dashboard.

Steps to Detect Keys Using the IMMO 4 CAN-BUS UDS Platform

ደረጃ 1: Connect the GT115 to the dashboard and connect it to the power supply.
ደረጃ 2: Press the start button, press the ignition button, and then press the Dash button.
ደረጃ 3: The instrument panel displays safe, and the key sensor coil flashes for 3 seconds and then goes out. It indicates that the key is not recognized.

ደረጃ 4: Connect the GT115 to the dashboard and connect it to the power supply.
ደረጃ 5: Press the start button, press the ignition button, and then press the Dash button.
ደረጃ 6: The instrument panel displays the mileage, and the key sensor coil flashes and then goes out. It indicates that the key has been identified.

Steps to Use POGO PIN on IMMO 4 CAN-BUS UDS Platform

ደረጃ 1፡ Connect GT115 to the instrument panel and power it on.
ደረጃ 2: First press the red ignition button, then press the “Dash” button

ደረጃ 3: Then use the pogo pin probe to poke the pogo pin point in the instrument chip.

ደረጃ 4: After poking, do not let go and press the start button again.
ደረጃ 5: Wait for 5 seconds and then release the pogo pin probe.

ደረጃ 6: At this time, only one light is on, indicating that the instrument has successfully entered the pogo pin mode.

Steps to Use on the MQB Platform

ደረጃ 1: Connect the gateway.

ደረጃ 2: Connect the BCM module.

ደረጃ 3: Connect the instrument.

ደረጃ 4: Connect the engine.

ደረጃ 5፡ Finally, turn on the power.

ደረጃ 6፡ Press the start button and the red ignition switch button again.
ደረጃ 7፡ Then you can connect other devices for testing, diagnoses, programming and coding.

Steps to Use Engine Independent Communication

ደረጃ 1: Connect the engine with colored jumper wires.

ደረጃ 2፡ ከኃይል ጋር ይገናኙ.

ደረጃ 3: Press in sequence: power switch start, ignition switch IGN, engine button switch ENG.
ደረጃ 4: Then connect other devices to the OBD port for testing and diagnosis.

መለዋወጫዎች፡

1pc x GT115 MQB IMMO4 CAN-Bus UDS 4th Generation IMMO System Test Platform 1pc x PDF manual

Shenzhen Sinoy Technology Co., Ltd
ሁሉም መብቶች የተጠበቁ ናቸው።
www.godiag.com
+86 18813687743
Sales@GoDiag.comhttps://h5.shengcai.net/wwei/url?url=H666G_0Kx6G
ስላነበቡ እናመሰግናለን!

ሰነዶች / መርጃዎች

GODIAG GT115 IMMO4 CAN Bus UDS Test Platform [pdf] የተጠቃሚ መመሪያ GT115, GT115 IMMO4 CAN Bus UDS Test Platform, GT115, IMMO4 CAN Bus UDS Test Platform, UDS Test Platform, Test Platform, Platform

ዋቢዎች

• የተጠቃሚ መመሪያ