Igwe nyocha omenala MARSON MT82M

Ozi ngwaahịa

MT82M bụ igwe nyocha 2D emebere maka ntinye n'ime ngwaọrụ dị iche iche. Ntuziaka njikọta a na-enye ozi zuru ezu na ntanetị eletrik, ọrụ pin, imewe sekit mpụga, na nkọwapụta eriri.

Okwu mmalite
Igwe nyocha MT82M nwere njikọ FPC nwere pin 12 maka ihu anụ ahụ.

Ihe Ngosi
Enyere eserese ngọngọ nke na-egosi akụkụ na njikọ nke MT82M Scan Engine na ntuziaka njikọta.

Igwe ọkụ eletrik
Igwe nyocha MT82M na-eji njikọ FPC 0.5-pitch 12-pin maka interface eletrik.

Nkenye Ọrụ
Ọrụ pin maka MT82M Scan Engine bụ nke a:

Ntụtụ #	Signal	I/O	Nkọwa
1	NC	—	Echekwara
2	VIN	PWR	Nkwanye ike: 3.3V DC
3	GND	PWR	Ike na ala mgbaama
4	RXD	Ntinye	Data enwetara: ọdụ ụgbọ mmiri nsonye
5	TXD	Mpụta	Ebufere Data: Oghere Usoro mmepụta ọdụ ụgbọ mmiri
6	D-	Mpụta	Mbufe mgbama USB dị iche iche (USB D-)
7	D+	Mpụta	Mbufe mgbama USB dị iche iche (USB D+)
8	PWRDWN/WAKE	Ntinye	Ike mgbada: Mgbe ọ dị elu, ihe ngbanwe ahụ nọ na ọnọdụ ike dị obere Teta: Mgbe ọ dị ala, ihe ngbanwe ahụ nọ na ọnọdụ arụ ọrụ
9	BPR	Mpụta	Beeper: Mmepụta beeper dị ugbu a dị ala
10	nDLED	Mpụta	Decode LED: Mmepụta ngbanwe LED dị ala ugbu a
11	NC	—	Echekwara
12	nTRIG	Ntinye	Mkpali: ahịrị na-akpali ngwaike. Ịnya ntụtụ a dị ala kpatara ya ihe nyocha iji malite nyocha na decode nnọkọ

 Nhazi okirikiri nke mpụga
Ntuziaka njikọta na-enye atụmatụ sekit maka ịnya LED mpụga maka ngosipụta ọgụgụ dị mma, beeper mpụga, yana sekit na-akpalite maka igwe nyocha.

Ezi agụ ikanam circuit
A na-eji akara nDLED sitere na pin 10 nke njikọ FPC 12-pin iji chụpụ LED mpụga maka ngosipụta ọgụgụ dị mma.

Circuit Beeper

A na-eji mgbama BPR sitere na pin 9 nke njikọ FPC 12-pin iji kwọọ beeper mpụga.

Trigger Circuit
A na-eji mgbama nTRIG sitere na pin 12 nke njikọ FPC 12-pin iji nye mgbama iji kpalite nnọkọ ngbanwe.

Ịse eriri USB
Enwere ike iji eriri FFC nwere pin 12 jikọọ igwe nyocha MT82M na ngwaọrụ nnabata. Nhazi eriri ga-adakọrịrị na nkọwapụta enyere na ntuziaka njikọta. A na-atụ aro ka iji ihe nkwado maka njikọ na eriri USB ma belata mgbochi eriri maka njikọ a pụrụ ịdabere na ya na ịrụ ọrụ kwụsiri ike.

Ntuziaka ojiji ngwaahịa

Iji tinye igwe nyocha MT82M n'ime ngwaọrụ gị, soro usoro ndị a:

1. Review eserese ngọngọ enyere na ntuziaka njikọta iji ghọta ihe mejupụtara na njikọ nke MT82M Scan Engine.
2. Gbaa mbọ hụ na ị nwere eriri FFC nwere pin12 dabara adaba nke na-ezute nkọwapụta ndị akpọrọ na ntuziaka njikọta.
3. Jikọọ njikọ FPC 12-pin nke MT82M Scan Engine na njikọ kwekọrọ na ngwaọrụ nnabata gị site na iji eriri FFC.
4. Ọ bụrụ na ịchọrọ iji ihe nrịbama mpụga, dị ka ọkụ ọkụ ma ọ bụ beeper, rụtụ aka na eserese sekit enyere na ntuziaka njikọta wee jikọọ ha otu a.
5. Ọ bụrụ na ịchọrọ ịkpalite nyocha na decode nnọkọ, jiri akara nTRIG sitere na pin 12 nke njikọ FPC 12-pin. Gbaa ntụtụ a ala ka ịmalite usoro nyocha.

Site n'ịgbaso ntuziaka ndị a, ị nwere ike ịmekọrịta ma jiri MT82M Scan Engine na ngwaọrụ gị.

Okwu mmalite

• MT82M Otu mpempe kọmpat 2D Scan Engine na-enye arụmọrụ nyocha ngwa ngwa na ọnụ ahịa asọmpi yana ụdị kọmpat. Site na imewe ya niile, igwe nyocha MT82M 2D nwere ike ijikọ ngwa ngwa na ngwa ndị dị ka njikwa ohere, kiosk lọtrị na ngwa elektrọn ndị ahịa.
• Igwe nyocha MT82M 2D nwere 1 ọkụ ọkụ, 1 aimer LED na ihe mmetụta onyonyo dị elu nwere microprocessor nke nwere ngwa ngwa siri ike iji chịkwaa akụkụ niile nke arụmọrụ ma mee ka nkwukọrịta ya na sistemụ nnabata karịa ọkọlọtọ nzikọrịta ozi.
• Ọtụtụ interface dị. UART interface na-ekwurịta okwu na sistemụ nnabata n'elu nkwukọrịta UART; USB interface na-eṅomi eriri USB HID ma ọ bụ ngwaọrụ ọdụ ụgbọ mmiri Virtual COM ma na-ekwurịta okwu na sistemụ nnabata n'elu USB.

Ihe Ngosi

Igwe ọkụ eletrik

Nkenye Ọrụ

• Ihe ngosi anụ ahụ nke MT82M nwere njikọ FPC 0.5-pitch 12-pin. Ọgụgụ dị n'okpuru na-egosi ọnọdụ njikọ na pin1.

Nhazi okirikiri nke mpụga

Ezi agụ ikanam circuit
A na-eji sekit dị n'okpuru ebe a na-ebugharị LED mpụga maka ihe ngosi ọgụgụ dị mma. Mgbama nDLED sitere na pin10 nke njikọ FPC 12-pin.

Circuit Beeper
A na-eji sekit dị n'okpuru ebe a na-akwọ ụgbọala mpụta beeper. Mgbama BPR sitere na pin9 nke njikọ FPC 12-pin.

Trigger Circuit
A na-eji sekit dị n'okpuru ebe a iji nye igwe nyocha ihe mgbaàmà iji kpalite nnọkọ ngbanwe. Mgbama nTRIG sitere na pin12 nke njikọ FPC 12-pin.

Ịse eriri USB

FFC USB (otu: mm)
Enwere ike iji eriri FFC nwere pin 12 jikọọ MT82M iji kwado ngwaọrụ. Nhazi eriri ga-adakọrịrị na nkọwapụta egosiri n'okpuru. Jiri ihe nkwado maka njikọta na eriri ma belata mgbochi eriri maka njikọ a pụrụ ịdabere na ya na ịrụ ọrụ kwụsiri ike

Nkọwapụta

Okwu mmalite

• Isiakwụkwọ a na-enye nkọwa nka nke MT82M. A na-egosipụtakwa usoro ọrụ, oke nyocha na akụkụ nyocha.

Nkọwa nka nka

Optic & Arụmọrụ
Isi Iyi Ìhè	Ọcha ọkụ ọkụ
Ebumnuche	Ikanam uhie na-ahụ anya
Sensọ	1280 x 800 (Megapikselụ)
Mkpebi	3mil/ 0.075mm (1D) 7mil/ 0.175mm (2D)
Ubi nke View	Kehoraizin 46° kwụ ọtọ 29°
Ike ianomi	Mpempe akụkụ ± 60° Akụkụ Skew ± 60° Mpịakọta akụkụ 360°
Bipụta oke nha	20%
Omimi nke Ubi (Gburugburu ebe obibi: 800 lux)	5 Mil Code39: 40 ~ 222mm
	13 Mil UPC/EAN: 42 ~ 442mm
	15 Mil Code128: 41 ~ 464mm
	15 Mil QR Code: 40 ~ 323mm
	6.67 Mil PDF417: 38 ~ 232mm
	10 Mil Data Matrix: 40 ~ 250mm
Njirimara anụ ahụ
Akụkụ	W21.6 x L16.1 x H11.9 mm
Ibu	3.7g
Agba	Nwa
Ihe onwunwe	Plastic
Njikọ	12pin ZIF (pitch = 0.5mm)
USB	eriri flex 12pin (pitch = 0.5mm)
Eletriki

Ọrụ Voltage	3.3VDC ± 5%
Na-arụ ọrụ ugbu a	<400mA
Njikere Ugbu a	<70mA
Ike dị ala ugbu a	10mA ± 5%
Njikọta
Interface	UART
	USB (ahụigodo HID)
	USB (Virtual COM)
gburugburu onye ọrụ
Okpomọkụ na-arụ ọrụ	-10°C ~ 50°C
Okpomọkụ nchekwa	-40°C ~ 70°C
iru mmiri	5% ~ 95% RH (na-adịghị emekọrịta ihe)
Dobe Ogologo	1.5M
Ambient Light	100,000 Lux (Ìhè anyanwụ)
Ihe ngosi 1D	UPC-A / UPC-E EAN-8 / EAN-13 Koodu mpaghara:: 128 Koodu mpaghara:: 39 Koodu mpaghara:: 93 Koodu mpaghara:: 32 Koodu 11 Codabar Plessey MSI Ejikọtara 2 nke 5 IATA 2 nke 5 Matrix 2 nke 5 2 nke 5 Pharmacode GS1 Databar kwụ ọtọ Ụgwọ nke ụlọ ọrụ GS1 Databar Expanded GS1 Databar Limited Koodu mejupụtara-A/B/C
Ihe ngosi 2D	Koodu QR Micro QR Code Matrix data

	PDF417 MicroPDF417 Aztec MaxiCode DotCode
Nhazi
ESD	Arụ ọrụ mgbe 4KV kọntaktị, 8KV ikuku ihapu (Ọ na-achọ ụlọ emebere maka nchekwa ESD ma kpafuo site na mpaghara eletrik.)
EMC	TBA
Nkwenye nchekwa	TBA
gburugburu ebe obibi	WEEE, RoHS 2.0

Interface 

UART interface
Mgbe ejikọrọ igwe nyocha na ọdụ ụgbọ mmiri UART nke ngwaọrụ nnabata, igwe nyocha ga-eme ka nkwukọrịta UART na-akpaghị aka.

N'okpuru bụ protocol nzikọrịta ozi nke ndabara:

• Baud ọnụego: 9600
• Bitt data: 8
• Parity: Ọ dịghị
• Kwụsị Bit: 1
• Ikwe aka: Ọ dịghị
• Ogologo oge njikwa usoro: Ọ nweghị
• ACK/NAK: Gbanyụọ
• BCC: Gbanyụọ

Barcode nhazi interface:

USB HID Interface
A ga-eme ka nnyefe ahụ dị ka ntinye ahụigodo USB. Onye ọbịa na-enweta mkpịsị ugodi na ahụigodo mebere. Ọ na-arụ ọrụ na ndabere Plug na Play na ọ nweghị ọkwọ ụgbọ ala achọrọ.

Barcode nhazi interface:USB VCP Interface
Ọ bụrụ na ejikọrọ nyocha na ọdụ ụgbọ USB na ngwaọrụ nnabata, njirimara USB VCP na-enye ngwaọrụ nnabata ohere ịnweta data n'ụzọ dị ka ọdụ ụgbọ mmiri na-eme. Achọrọ onye ọkwọ ụgbọ ala mgbe ị na-eji njirimara a.

Barcode nhazi interface:

Usoro ọrụ

1. Na ike elu, MT82M na-eziga akara ngosi Power-Up n'elu Buzzer na LED pins dị ka ihe na-egosi na MT82M na-abanye na Njikere Mode ma dị njikere maka ịrụ ọrụ.
2. Ozugbo MT82M kpalitere site na ngwaike ma ọ bụ usoro ngwanrọ, MT82M ga-ebunye ọkụ nke dabara na mpaghara ihe mmetụta. view.
3. Ihe mmetụta onyonyo mpaghara na-esetịpụ onyonyo nke barcode wee mepụta ụdị ebili mmiri analọgụ, nke bụ sampduru ma nyochaa site na decoder firmware na-agba ọsọ na MT82M.
4. N'elu koodu koodu na-aga nke ọma, MT82M na-agbanyụ ọkụ ọkụ, na-eziga akara ngosi dị mma na Buzzer na LED ma na-ebufe data edepụtara na onye ọbịa.

Akụkụ Mechanical

(Nkeji = mm)

Ịwụnye

Emebere igwe nyocha ahụ kpọmkwem maka ntinye n'ime ụlọ ndị ahịa maka ngwa OEM. Agbanyeghị, arụmọrụ injin nyocha ahụ ga-emetụta nke ọma ma ọ bụ mebie kpamkpam mgbe etinyere ya n'ime ogige na-ekwesịghị ekwesị.
Ịdọ aka ná ntị: Akwụkwọ ikike nwere oke bụ ihe efu ma ọ bụrụ na akwadoghị ndụmọdụ ndị a mgbe ị na-arịgo igwe nyocha.

Ịdọ aka ná ntị mgbapụ eletrọstatic

A na-ebufe igwe nyocha niile na nkwakọ ngwaahịa nchekwa ESD n'ihi ọdịdị dị nro nke ngwa eletrik ekpughere.

1. Na-eji eriri nkwojiaka n'ala na mpaghara ọrụ gbadoro ụkwụ mgbe ọ bụla mgbe ị na-ebupụ ma na-ejikwa igwe nyocha.
2. Wụnye igwe nyocha n'ime ụlọ emebere maka nchekwa ESD na mpaghara eletrik kpafuru akpafu.

Akụkụ Mechanical
Mgbe ị na-echekwa igwe nyocha site na iji skru igwe:

1. Hapụ ohere zuru oke iji nabata oke nke igwe nyocha.
2. Agafela 1kg-cm (0.86 lb-in) nke torque mgbe ị na-echekwa igwe nyocha n'aka onye ọbịa.
3. Jiri omume ESD dị mma mgbe ị na-ejikwa ma na-ebugo igwe nyocha.

Ngwa windo
Nke a bụ nkọwa nke ihe windo atọ ama ama:

1. Poly-methyl Methacrylic (PMMA)
   Allyl Diglycol Carbonate (ADC)
2. Igwe mmiri na-ekpo ọkụ na-ekpo ọkụ

Cell Cast Acrylic (ASTM: PMMA)
A na-emepụta ihe nkedo cell acrylic, ma ọ bụ Poly-methyl Methacrylic site na nkedo acrylic n'etiti mpempe akwụkwọ enyo ziri ezi. Ihe a nwere ezigbo ngwa anya, mana ọ dị nro ma nwee ike ibuso kemịkalụ ọgụ, nrụgide igwe na ọkụ UV. A na-atụ aro ka ị nweta acrylic siri ike na Polysiloxane iji nye nguzogide abrasion na nchebe pụọ na ihe gburugburu ebe obibi. Enwere ike ịkpụ acrylic n'ụdị na-adịghị mma na ultrasonically welded.

Ihe nkedo cell ADC, Allyl Diglycol Carbonate (ASTM: ADC)
A makwaara dị ka CR-39TM, ADC, plastic ntọala okpomọkụ nke a na-ejikarị eme ihe maka ugogbe anya plastik, nwere ezigbo kemịkalụ na nguzogide gburugburu ebe obibi. O nwekwara ike ime elu ala na-agafeghị oke ma yabụ na ọ chọghị
mkpuchi siri ike. Enweghị ike iji ultrasonically welded ihe a.

Igwe ọkụ na-ekpo ọkụ nke kemịkal
Glass bụ ihe siri ike nke na-enye ezigbo ọkọ na nguzogide abrasion. Otú ọ dị, iko a na-ekpochapụghị ọkụ na-akụkụ. Mmụba ike mgbanwe na obere mgbagha ngwa anya chọrọ iwe ọkụ. A pụghị iji ultrasonically welded iko ma na-esiri ike ịkpụ n'ime ụdị adịghị mma.

Ngwongwo	Nkọwa
Mbufe Spectral	85% kacha nta site na 635 ruo 690 nanometer
Ọkpụrụkpụ	<1 mm
Mkpuchi	Akụkụ abụọ a ga-ekpuchi mkpuchi mkpuchi iji nye 1% reflectivity kachasị site na 635 ruo 690 nanometers n'akụkụ akụkụ windo ọnụ. Ihe mkpuchi mgbochi ntụgharị nwere ike ibelata ọkụ nke na-egosipụta azụ na ikpe nnabata. Ihe mkpuchi ga-agbaso na nrube isi ike Ihe achọrọ maka MIL-M-13508

Ndokwa windo

Ekwesịrị idowe mpio ahụ nke ọma ka ọkụ ọkụ na ihie ndị na-atụ anya gafere ka o kwere mee na enweghị ntụgharị azụ n'ime injin ahụ. Ụlọ ime ụlọ nke emebereghị nke ọma ma ọ bụ nhọrọ na-ekwesịghị ekwesị nke ihe windo nwere ike imebi ọrụ injin ahụ.

N'ihu nke ụlọ engine na elu nke dị n'elu nke windo ekwesịghị gafere a + b (a ≦ 0.1mm, b ≦ 2mm).

Nha windo
Window ekwesịghị igbochi ubi nke view ma kwesiri ịdị nha iji nabata envelopu ebumnuche na ọkụ ndị egosiri n'okpuru.

Nlekọta windo

N'akụkụ nke windo, arụmọrụ nke MT82M ga-ebelata n'ihi ụdị ọ bụla nke ọkọ. Ya mere, ibelata mmebi nke windo, enwere ihe ole na ole ka a ga-achọpụta.

1. Zere imetụ windo ahụ aka ka o kwere mee.
2. Mgbe ị na-ehicha elu windo, biko jiri akwa nhicha na-adịghị mma, wee jiri nwayọọ hichaa windo onye ọbịa ahụ na akwa nke ejirila ihe nhicha iko fesa.

IWU

Igwe nyocha MT82M kwekọrọ n'ụkpụrụ ndị a:

1. Nkwekọrịta Electromagnetic - TBA
2. Ntinye aka eletrik - TBA
3. Nchekwa fotobiological – TBA
4. Iwu gburugburu ebe obibi - RoHS 2.0, WEEE

Ngwa mmepe

MB130 Demo Kit (P/N: 11D0-A020000) gụnyere MB130 Multi I/O Board (P/N: 9014-3100000) na eriri USB micro. MB130 Multi I / O Board na-eje ozi dị ka ihe interface maka MT82M na accelerates na ule na mwekota na onye ọbịa usoro. Biko kpọtụrụ onye na-ere ahịa gị maka ịnye ozi.
MB130 Multi I/O Board (P/N: 9014-3100000)

Nkwakọ ngwaahịa

1. Tray (nha: 24.7 x 13.7 x 2.7cm): tray ọ bụla nwere 8pcs nke MT82M.
2. Igbe (nha: 25 x 14 x 3.3cm): Igbe ọ bụla nwere 1pc nke tray, ma ọ bụ 8pcs nke MT82M.
3. Katọn (nha: 30 x 27 x 28cm): Katọn ọ bụla nwere igbe 16pcs, ma ọ bụ 128pcs nke MT82M.

Ụdị akụkọ ihe mere eme

Mkpu.	Ụbọchị	Nkọwa	Enyere ya
0.1	2022.02.11	Mwepụta akwụkwọ nke mbido	Shaw
0.2	2022.07.26	Schematic Example, Ọnụego nyocha, Okpomọkụ na-arụ ọrụ.	Shaw
0.3	2023.09.01	Ngwa mmepe emelitere	Shaw
0.4	2023.10.03	Emegharịrị RS232 ka ọ bụrụ UART wepụrụ ọnụ ọgụgụ nyocha Emelitere Ụdị DOF, Akụkụ, Arọ, Na-arụ ọrụ ugbu a, njikere ugbu a	Shaw

Ụgwọ nke ụlọ ọrụ Marson Technology Co., Ltd.
9F., 108-3, Minquan Rd., Xindian Dist., New Taipei City, Taiwan
EKWU: 886-2-2218-1633
Faksị: 886-2-2218-6638
Email: info@marson.com.tw
Web: www.marson.com.tw

Akwụkwọ / akụrụngwa

	Igwe nyocha omenala MARSON MT82M [pdf] Ntuziaka onye ọrụ Igwe nyocha omenala MT82M, MT82M, igwe nyocha nke omenala, igwe nyocha
	Igwe nyocha omenala MARSON MT82M [pdf] Akwụkwọ ntuziaka onye ọrụ Igwe nyocha omenala MT82M, MT82M, igwe nyocha nke omenala, igwe nyocha

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ