Arduino Nano RP2040 Jikọọ na nkụnye eji isi mee
Nkọwapụta
- Ebe nchekwa: AT25SF128A 16MB ma ọ bụ Flash
- Ọnụego mbufe data QSPI: Ruo 532Mbps
- Usoro mmemme/ehichapụ: 100K
Atụmatụ:
- Pedometer dị elu, ihe nchọpụta nzọụkwụ na counter steepụ
- Nchọpụta ngagharị dị mkpa, nchọpụta tilt
- Ọkọlọtọ nkwụsị: ọdịda efu, iteta, nghazi 6D/4D, pịa wee pịa ugboro abụọ.
- Igwe steeti nwere njedebe mmemme nwere ike ime: accelerometer, gyroscope, na sensọ mpụga
- Isi mmụta igwe
- Ihe mmetụta okpomọkụ agbakwunyere
- Ọdịmma dị elu nke ime NIST SP 800-90A/B/C Ndị na-emepụta ọnụọgụ ọnụọgụ (RNG)
- Nkwado buut echekwara:
- Nkwenye mbinye aka koodu ECDSA zuru ezu
- Ngwa nri / mbinye aka echekwara nke nhọrọ
- Nkwụsị igodo nkwurịta okwu nhọrọ tupu ị nweta buut
- Izo ya ezo/Nnwale maka ozi iji gbochie mwakpo n'ime ụgbọ
- I/O: 14x Digital Pin, 8x Analog Pin
- Ọnụ ụzọ: Micro USB, UART, SPI, I2C Nkwado
- Ike: Buck mgbada mgbada
Ntuziaka ojiji ngwaahịa
Na-amalite
Iji malite iji ngwaahịa a:
- Jikọọ osisi ahụ na kọmputa gị site na iji eriri USB Micro.
- Wụnye IDE dị mkpa ma ọ bụ jiri Arduino Web Onye nchịkọta akụkọ/Arduino Cloud.
Mmemme
Iji hazie bọọdụ:
- Dee koodu gị ma ọ bụ jiri sample sketị nyere.
- Bulite koodu na bọọdụ site na interface ahọpụtara (UART, SPI, I2C).
Ịgbanyụ/ Gbanyụọ
Iji mee ka bọọdụ dị ike:
- Gbaa mbọ hụ na ntinye voltage na-ezute ọnọdụ ọrụ akwadoro.
- Jikọọ isi iyi ọkụ ma ọ bụ njikọ USB iji mee ka bọọdụ dị ike.
Ajụjụ A na-ajụkarị (FAQ)
- Ajụjụ: Gịnị bụ ọnọdụ ọrụ akwadoro maka bọọdụ a?
A: Ọnọdụ ọrụ akwadoro gụnyere ntinye voltage nso nke 4.75V ruo 5.25V, yana mmepụta 3.3V maka ngwa onye ọrụ yana oke okpomọkụ na-arụ ọrụ nke 80°C. - Ajụjụ: Kedu ka m ga-esi nwetaghachi bọọdụ ahụ ma ọ bụrụ na enwere nsogbu?
A: Ị nwere ike na-ezo aka na "Board Iweghachite" ngalaba na ntuziaka maka nzọụkwụ na-agbake osisi na ikpe. - Nkọwa
Njikọ Arduino® Nano RP2040 juru eju na-eweta microcontroller Raspberry Pi RP2040 ọhụrụ na ụdị Nano. Mee ọtụtụ n'ime dual-core 32-bit Arm® Cortex®-M0+ iji rụọ ọrụ ịntanetị nke ihe site na iji njikọ Bluetooth® na Wi-Fi site na modul U-blox® Nina W102. Banye n'ime ọrụ ụwa n'ezie na ngwa ngwa ngwa ngwa, gyroscope, RGB LED, na igwe okwu. Mepụta ngwọta AI siri ike agbakwunyere na obere mbọ iji Arduino® Nano RP2040 Jikọọ!
Mpaghara ebumnuche
Ịntanetị nke Ihe (IoT), mmụta igwe, prototyping,
Atụmatụ
- Raspberry Pi RP2040 Microcontroller
- 133MHz 32bit Dual Core Arm® Cortex®-M0+
- 264kB on-chip SRAM
- Direct ebe nchekwa Access (DMA) njikwa
- Nkwado maka ihe ruru 16MB nke ebe nchekwa Flash-chip site na ụgbọ ala QSPI USB 1.1 na PHY raara onwe ya nye, yana nkwado onye ọbịa na ngwaọrụ.
- Igwe steeti PIO 8
- IO (PIO) nwere ike ime maka nkwado mpụta gbatịpụrụ
- 4 ọwa ADC nwere ihe mmetụta okpomọkụ dị n'ime, 0.5 MSa/s, 12-bit ntụgharị SWD Debugging
- 2 na-chip PLL iji mepụta USB na isi elekere
- 40nm usoro ọnụ
- Nkwado ụdị ike dị ala ọtụtụ
- USB 1.1 onye ọbịa / ngwaọrụ
- Ime Voltage Regulator inye isi voltage
- Ụgbọ ala na-arụ ọrụ dị elu (AHB)/Bus peripheral Advanced (APB)
- U-blox® Nina W102 Wi-Fi/Bluetooth® Module
- 240MHz 32bit Dual Core Xtensa LX6
- 520kB on-chip SRAM
- 448 Kbyte ROM maka booting na isi ọrụ
- 16 Mbit FLASH maka nchekwa koodu gụnyere izo ya ezo ngwaike iji chebe mmemme na data
- 1 kbit EFUSE (ebe nchekwa anaghị ehichapụ) maka adreesị MAC, nhazi modul, Flash-encryption, na Chip-ID
- IEEE 802.11b/g/n otu-band 2.4 GHz Wi-Fi arụ ọrụ
- Njikọ Bluetooth® 4.2
- Ejikọtara Planar Inverted-F Antenna (PIFA)
- 4 x 12-bit ADC
- 3x I2C, SDIO, CAN, QSPI
- Ebe nchekwa
- AT25SF128A 16MB ma ọ bụ Flash
- Ọnụego mbufe data QSPI ruru 532Mbps
- 100K mmemme / ihichapụ okirikiri
- ST LSM6DSOXTR 6-axis IMU
- Gyroscope 3D
- ± 2 / ± 4 / ± 8 / ± 16 g zuru oke
- 3D Accelerometer
- ± 125 / ± 250 / ± 500 / ± 1000 / 2000 dps zuru oke
- Pedometer dị elu, ihe nchọpụta nzọụkwụ na counter nzọụkwụ
- Nchọpụta ngagharị dị mkpa, nchọpụta tilt
- Ọkọlọtọ nkwụsị: ọdịda efu, iteta n'ụra, ntụgharị 6D/4D, pịa wee pịa igwe steeti nwere njedebe mmemme: accelerometer, gyroscope na ihe mmetụta mpụga Machine Learning Core
- Ihe mmetụta okpomọkụ agbakwunyere
- Gyroscope 3D
- Igwe okwu ST MP34DT06JTR MEMS
- AOP = 122.5 dBSPL
- Oke mgbama na mkpọtụ 64dB
- Mmetụta uche n'ebe niile
- -26 dBFS ± 1 dB uche
- RGB LED
- Anode nkịtị
- Jikọọ na U-blox® Nina W102 GPIO
- Microchip® ATECC608A Crypto
- Onye na-arụkọ ọrụ Cryptographic nwere nchekwa igodo dabere na ngwaike echekwara
- I2C, SWI
- Nkwado ngwaike maka Algorithms Symmetric:
- SHA-256 & HMAC Hash gụnyere mgbanaka gburugburu ebe nchekwa/iweghachi
- AES-128: Encrypt/Decrypt, Galois Field Multiply for GCM
- Ọdịmma dị elu nke ime NIST SP 800-90A/B/C Ndị na-emepụta ọnụọgụ ọnụọgụ (RNG)
- Nkwado buut echekwara:
- Nkwenye mbinye aka koodu ECDSA zuru oke, mgbari / mbinye aka echekwara nhọrọ
- Nkwụsị igodo nkwurịta okwu nhọrọ tupu ị nweta buut
- Izo ya ezo/Nnwale maka ozi iji gbochie mwakpo n'ime ụgbọ
- I/O
- 14x Digital Pin
- 8x Analog Pin
- Micro USB
- Nkwado UART, SPI, I2C
- Ike
- Buck mgbada mgbada
- Ozi nchekwa
- Klas A
The Board
Ngwa Examples
- Enwere ike ịmegharị njikọ Arduino® Nano RP2040 ka ọ bụrụ usoro eji eme ihe n'ọtụtụ ebe ekele maka microprocessor dị ike, oke sensọ onboard na ụdị Nano. Ngwa enwere ike gụnyere:
- Kọmputa EdgeJiri ngwa ngwa na nnukwu microprocessor RAM na-agba TinyML maka nchọpụta anomaly, nchọpụta ụkwara, nyocha mmegharị ahụ, na ndị ọzọ.
- Ngwa ndị nwere ike eyi: Obere akara ukwu Nano na-enye ohere nke ịnye igwe mmụta igwe na ngwaọrụ dị iche iche na-eyi egwu gụnyere ndị na-egwu egwuregwu na ndị na-ahụ maka VR.
- Onye enyemaka olu: Njikọ Arduino® Nano RP2040 gụnyere igwe okwu omnidirectional nke nwere ike ịrụ ọrụ dị ka onye enyemaka dijitalụ ma mee ka njikwa olu maka ọrụ gị.
Ngwa ngwa
- Igwe USB Micro
- 15-pin 2.54mm nkụnye eji isi mee nwoke
- 15-pin 2.54mm nkụnye eji isi mee
Ngwaahịa ndị emetụtara
- Ike ndọda: Nano I/O Shield
Ogo
Ọnọdụ ọrụ akwadoro
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| VIN | Ntinye voltage sitere na VIN pad | 4 | 5 | 20 | V |
| VUSB | Ntinye voltage site na njikọ USB | 4.75 | 5 | 5.25 | V |
| V3V3 | 3.3V mmepụta na ngwa onye ọrụ | 3.25 | 3.3 | 3.35 | V |
| I3V3 | 3.3V mmepụta ugbu a (gụnyere onboard IC) | – | – | 800 | mA |
| VIH | Tinye ọkwa dị elu voltage | 2.31 | – | 3.3 | V |
| VIL | Tinye obere ọkwa voltage | 0 | – | 0.99 | V |
| Ọnụ ego nke IOH Max | Ugbu a na VDD-0.4 V, mmepụta setịpụrụ elu | 8 | mA | ||
| IOL Max | Ugbu a na VSS+0.4 V, ewepụtarala ihe nrụpụta dị ala | 8 | mA | ||
| VOH | Mmepụta elu voltage, 8mA | 2.7 | – | 3.3 | V |
| VOL | Mmepụta obere voltage, 8mA | 0 | – | 0.4 | V |
| N'elu | Okpomọkụ na-arụ ọrụ | -20 | – | 80 | Celsius C |
Oriri ike
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| PBL | Oriri ike na akaghị aka | TBC | mW | ||
| PLP | Oriri ike na ọnọdụ ike dị ala | TBC | mW | ||
| PMAX | Oriri ike kacha | TBC | mW |
Arụ ọrụ gafereview
Ihe Ngosi
Board Topology
N'ihu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| U1 | Raspberry Pi RP2040 Microcontroller | U2 | Ublox NINA-W102-00B Wi-Fi/Bluetooth® Module |
| U3 | N/A | U4 | ATECC608A-MAHDA-T Crypto IC |
| U5 | AT25SF128A-MHB-T 16MB Flash IC | U6 | MP2322GQH Onye na-achịkwa Buck-down |
| U7 | DSC6111HI2B-012.0000 MEMS Oscillator | U8 | MP34DT06JTR MEMS Omnidirectional igwe okwu IC |
| U9 | LSM6DSOXTR 6-axis IMU nwere isi mmụta igwe | J1 | Njikọ Micro USB nwoke |
| DL1 | Ike Green Na LED | DL2 | Wuru Oroma LED |
| DL3 | RGB Common Anode LED | PB1 | Tọgharịa bọtịnụ |
| JP2 | Analog Pin + D13 Pin | JP3 | Ntụtụ dijitalụ |
Azu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| SJ4 | 3.3V jumper (jikọrọ) | SJ1 | VUSB jumper (kwụpụrụ) |
Nhazi
- Ihe nhazi ahụ dabere na silicon Raspberry Pi RP2040 ọhụrụ (U1). Igwe njikwa micro a na-enye ohere maka mmepe ịntanetị nke ihe dị ala yana mmụta igwe agbakwunyere. Abụọ symmetrical Arm® Cortex®-M0+ mechiri na 133MHz na-enye ike mgbako maka mmụta igwe agbakwunyere yana nhazi ya na obere ike. Enyere ụlọ akụ isii kwụụrụ onwe ya nke 264 KB SRAM na 2MB. Nweta ebe nchekwa ozugbo na-enye njikọ ngwa ngwa n'etiti ndị na-arụ ọrụ na ebe nchekwa nwere ike ime ka ọ ghara ịdị na-arụ ọrụ yana isi ịbanye ọnọdụ ụra. Serial waya debug (SWD) dị site na buut site na pads n'okpuru osisi. RP2040 na-agba na 3.3V ma nwee volta dị n'imetage regulator na-enye 1.1V.
- RP2040 na-achịkwa mpụta na ntụtụ dijitalụ, yana atụdo analọg (A0-A3). A na-eji njikọ I2C dị na pin A4 (SDA) na A5 (SCL) maka ijikọ na akụkụ ndị dị n'ụgbọ mmiri ma jiri 4.7 kΩ resistor bulie ya. SWD Clock Line (SWCLK) na nrụpụta na-ejiri 4.7 kΩ resistor na-ebulikwa ya. Ihe oscillator MEMS dị na mpụga (U7) na-agba ọsọ na 12MHz na-enye ụda elekere. Programmable IO na-enyere aka na mmejuputa usoro nkwurịta okwu aka ike na ibu dị nta na isi nhazi isi. Ejiri interface ngwaọrụ USB 1.1 na RP2040 maka ibugo koodu.
Njikọ Wi-Fi/Bluetooth®
Enyere njikọ Wi-Fi na Bluetooth® site na modul Nina W102 (U2). RP2040 nwere naanị 4 ntụtụ analọgụ, a na-ejikwa Nina gbatịa nke ahụ ruo asatọ zuru oke dịka ọkọlọtọ na ụdị Arduino Nano nwere ntinye analọgụ 4 12-bit ọzọ (A4-A7). Na mgbakwunye, ihe Nina W-102 modul na-achịkwa anode RGB LED nke na-eme ka ọkụ na-apụ mgbe steeti dijitalụ dị elu yana na mgbe steeti dijitalụ dị ala. Igwe PCB dị n'ime n'ime modul na-ewepụ mkpa maka antenna mpụga. Nina W102 modul tinyekwara a dual core Xtensa LX6 CPU nke nwekwara ike hazie onwe ya na RP2040 site na pads n'okpuru bọọdụ iji SWD.
6-Axis IMU
Ọ ga-ekwe omume ịnweta gyroscope 3D na data accelerometer 3D site na LSM6DSOX 6-axis IMU (U9). Na mgbakwunye na ịnye data dị otú ahụ, ọ ga-ekwe omume ịme mmụta igwe na IMU maka nchọpụta mmegharị ahụ.
Ebe nchekwa mpụga
RP2040 (U1) nwere ohere ịnweta 16 MB nke ebe nchekwa ọkụ site na interface QSPI. Ihe nrụnye-in-ebe (XIP) nke RP2040 na-enye ohere ka sistemụ ahụ wee nweta ebe nchekwa flash mpụga dị ka a ga-asị na ọ bụ ebe nchekwa dị n'ime, na-ebughị ụzọ degharịa koodu ahụ na ebe nchekwa dị n'ime.
Cryptography
ATECC608A Cryptographic IC (U4) na-enye ike buut echekwara n'akụkụ SHA na AES-128 nkwado nzuzo / decryption maka nchekwa na ngwa Smart Home na Industrial IoT (IIoT). Na mgbakwunye, onye na-emepụta nọmba random dịkwa maka RP2040.
Igwe okwu
Ejikọrọ igwe okwu MP34DT06J site na interface PDM na RP2040. Igwe okwu MEMS dijitalụ bụ akụkụ niile ma na-arụ ọrụ site na mmetụ mmetụta nwere nnukwu mgbama (64 dB) maka oke mkpọtụ. A na-arụpụta ihe na-ahụ ihe, nke nwere ike ịchọpụta ebili mmiri dị egwu, site na iji usoro micromachining silicon pụrụ iche a raara nye iji mepụta sensọ ọdịyo.
RGB LED
RGB LED (DL3) bụ ọkụ anode nkịtị nke ejikọrọ na modul Nina W102. Igwe ọkụ na-agbanyụ mgbe ọnọdụ dijitalụ dị elu na mgbe ọnọdụ dijitalụ dị ala.
Osisi Ike
Enwere ike ịkwado njikọ Arduino Nano RP2040 site na ọdụ ụgbọ mmiri Micro USB (J1) ma ọ bụ ọzọ site na VIN na JP2. Ihe ntụgharị buck onboard na-enye 3V3 na microcontroller RP2040 yana akụkụ ndị ọzọ niile. Na mgbakwunye, RP2040 nwekwara ihe nhazi 1V8 dị n'ime.
Ọrụ Board
Mmalite – IDE
Ọ bụrụ na ịchọrọ ịhazi Arduino® Nano RP2040 Jikọọ mgbe ị na-anọghị n'ịntanetị, ịkwesịrị ịwụnye Arduino® IDE Desktop [1] Iji jikọọ njikwa Arduino® Edge na kọmputa gị, ị ga-achọ eriri USB micro. Nke a na-enyekwa ike na osisi ahụ, dị ka LED gosipụtara.
Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọọdụ Arduino® niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino® Web Editor [2], site na ịwụnye ngwa mgbakwunye dị mfe.
Arduino® Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro [3] ka ịmalite itinye koodu na ihe nchọgharị wee bulite ihe osise gị na bọọdụ gị.
Mmalite – Arduino Cloud
A na-akwado ngwaahịa Arduino® IoT niile na Arduino® IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data ihe mmetụta, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị.
Sampna Sketches
SampEnwere ike ịchọta ihe osise maka Arduino® Nano RP2040 Connect na "Ex".amples” menu na Arduino® IDE ma ọ bụ na ngalaba “Akwụkwọ” nke Arduino websaịtị [4]
Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ na-akpali akpali na ProjectHub [5], Arduino® Library Reference [6] na ụlọ ahịa dị n'ịntanetị [7] ebe. ị ga-enwe ike iji sensọ, actuators na ndị ọzọ mejuo osisi gị.
Iweghachite Board
Bọdụ Arduino niile nwere bootloader arụnyere n'ime ya nke na-enye ohere ịmegharị bọọdụ ahụ site na USB. Ọ bụrụ na eserese kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo ọ gbasịrị.
Pinouts njikọ
J1 Micro USB
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | V-BUS | Ike | 5V ike USB |
| 2 | D- | dị iche iche | USB data dị iche iche - |
| 3 | D+ | dị iche iche | USB data dị iche iche + |
| 4 | ID | Dijitalụ | Ejighi ya |
| 5 | GND | Ike | Ala |
JP1
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | TX1 | Dijitalụ | UART TX / Digital Pin 1 |
| 2 | RX0 | Dijitalụ | UART RX / Digital Pin 0 |
| 3 | RST | Dijitalụ | Tọgharia |
| 4 | GND | Ike | Ala |
| 5 | D2 | Dijitalụ | Pin dijitalụ 2 |
| 6 | D3 | Dijitalụ | Pin dijitalụ 3 |
| 7 | D4 | Dijitalụ | Pin dijitalụ 4 |
| 8 | D5 | Dijitalụ | Pin dijitalụ 5 |
| 9 | D6 | Dijitalụ | Pin dijitalụ 6 |
| 10 | D7 | Dijitalụ | Pin dijitalụ 7 |
| 11 | D8 | Dijitalụ | Pin dijitalụ 8 |
| 12 | D9 | Dijitalụ | Pin dijitalụ 9 |
| 13 | D10 | Dijitalụ | Pin dijitalụ 10 |
| 14 | D11 | Dijitalụ | Pin dijitalụ 11 |
| 15 | D12 | Dijitalụ | Pin dijitalụ 12 |
JP2
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | D13 | Dijitalụ | Pin dijitalụ 13 |
| 2 | 3.3V | Ike | 3.3V ike |
| 3 | REF | Analọg | NC |
| 4 | A0 | Analọg | Analog Pin 0 |
| 5 | A1 | Analọg | Analog Pin 1 |
| 6 | A2 | Analọg | Analog Pin 2 |
| 7 | A3 | Analọg | Analog Pin 3 |
| 8 | A4 | Analọg | Analog Pin 4 |
| 9 | A5 | Analọg | Analog Pin 5 |
| 10 | A6 | Analọg | Analog Pin 6 |
| 11 | A7 | Analọg | Analog Pin 7 |
| 12 | VUSB | Ike | Ntinye USB Voltage |
| 13 | REC | Dijitalụ | BOOTSEL |
| 14 | GND | Ike | Ala |
| 15 | VIN | Ike | Voltage Ntinye |
Rịba ama: Ihe ntụaka analọg voltagA na-edozi ya na +3.3V. Ejikọrọ A0-A3 na ADC RP2040. A4-A7 jikọọ na Nina W102 ADC. Na mgbakwunye, A4 na A5 na-eso ụgbọ ala I2C nke RP2040 na-ekekọrịta ma ejiri 4.7 KΩ resistors dọkpụrụ nke ọ bụla.
RP2040 SWD mpempe akwụkwọ
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | SWDIO | Dijitalụ | SWD Data Line |
| 2 | GND | Dijitalụ | Ala |
| 3 | SWCLK | Dijitalụ | Elekere SWD |
| 4 | + 3V3 | Dijitalụ | + 3V3 ụgbọ okporo ígwè |
| 5 | TP_RESETN | Dijitalụ | Tọgharia |
Nina W102 SWD Pad
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | TP_RST | Dijitalụ | Tọgharia |
| 2 | TP_RX | Dijitalụ | Oghere Usoro Rx |
| 3 | TP_TX | Dijitalụ | Oghere Usoro Tx |
| 4 | TP_GPIO0 | Dijitalụ | GPIO0 |
Ozi igwe
Asambodo
Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru naanị ọrụ anyị na ngwaahịa ndị dị n'elu kwekọrọ n'ihe achọrọ dị mkpa nke ntuziaka EU ndị a wee tozuo maka njem n'efu n'ime ahịa nke gụnyere European Union (EU) na European Economic Area (EEA).
Nkwupụta nke Nkwekọrịta na EU RoHS & REACH 211 01/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
| Ihe | Oke kacha (ppm) |
| Ndu (Pb) | 1000 |
| Ogwugwu (Cd) | 100 |
| Ebere (Hg) | 1000 |
| Chromium Hexavalent (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Mwepu: Ọnweghị mpụ a na-ekwu.
Boards Arduino na-akwado nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi nke kemịkalụ (REACH). Anyị na-ekwupụta enweghị nke SVHC (https://echa.europa.eu/)web/ guest/candidate-list-table), Ndekọ Candidate nke ihe dị oke mkpa maka ikike nke ECHA wepụtara ugbu a, dị na ngwaahịa niile (yana ngwugwu) n'ọnụọgụ mkpokọta na ntinye nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị nke ọ bụla n'ime ihe ndị e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na ihe ndị dị oke nchegbu (SVHC) na oke ọ bụla dị mkpa dị ka akọwapụtara. site na Mgbakwunye XVII nke ndepụta Candidate bipụtara EHA (European Chemical Agency) 1907/2006/EC.
FCC
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20cm n'etiti radiator & ahụ gị.
Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata na ọnọdụ pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụkpụrụ (s) RSS enweghị ikike ụlọ ọrụ Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ọrụ ngwaọrụ ahụ achọghị.
N'ebe a, Arduino Srl na-ekwupụta na ngwaahịa a na-akwado ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile. N'ebe a, Arduino Srl na-ekwupụta na ngwaahịa a na-akwado ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
| Ugboro ugboro | Ike Isotropic Radiated Ike kacha arụ ọrụ (EIRP) |
| TBC | TBC |
Ozi ụlọ ọrụ
| Aha Ụlọ Ọrụ | Arduino Srl |
| Adreesị ụlọ ọrụ | Site na Andrea Appiani, 2520900 MONZA |
Akwụkwọ ntụaka
| Ref | Njikọ |
| Arduino IDE (Desktọpụ) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (igwe ojii) | https://create.arduino.cc/editor |
| Cloud IDE na-amalite | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino- web-onye nchịkọta akụkọ-4b3e4a |
| Arduino Websaịtị | https://www.arduino.cc/ |
| Hub Project | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| PDM (igwe okwu) Library | https://www.arduino.cc/en/Reference/PDM |
| WiFiNINA (Wi-Fi, W102)
Ụlọ akwụkwọ |
https://www.arduino.cc/en/Reference/WiFiNINA |
| ArduinoBLE (Bluetooth®, W-102) Ọbá akwụkwọ | https://www.arduino.cc/en/Reference/ArduinoBLE |
| Ụlọ akwụkwọ IMU | https://reference.arduino.cc/reference/en/libraries/arduino_lsm6ds3/ |
| Ụlọ ahịa dị n'ịntanetị | https://store.arduino.cc/ |
Akụkọ ngbanwe
| Ụbọchị | Ndozigharị | Mgbanwe |
| 12/07/2022 | 3 | Mmelite mmezi izugbe |
| 02/12/2021 | 2 | Mgbanwe arịọrọ maka asambodo |
| 14/05/2020 | 1 | Mwepụta mbụ |
Arduino® Nano RP2040 Jikọọ
Emegharịrị: 16/02/2024
Akwụkwọ / akụrụngwa
 |
Arduino Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee, Nano RP2040, Jikọọ na nkụnye eji isi mee, nkụnye eji isi mee |