ARDUINO ABX00027 Nano 33 IoT Development Board
Nta
SAM 21 G18A
- Processor
- 256 KB Flash
- 32 KB Flash
- Power-On Reset (POR) thiab Brown Out Detection (BOD)
- Peripherals
- 12 channel DMA
- 12 channel xwm txheej system
- 5 x 16-ntsis Timer/Counter
- 3x 24-ntsis timer / txee nrog txuas ntxiv ua haujlwm
- 32-ntsis RTC
- Watchdog Timer
- CRC-32 generator
- Full ceev Host/Device USB nrog 8 endpoints
- 6 x SERCOM (USART, I2C, SPI, LIN)
- Ob-channel I2S
- 12 ntsis 350ksps ADC (txog 16 ntsis nrog oversampling)
- 10 ntsis 350ksps DAC
- Sab nraud Interrupt Controller (txog 16 kab)
Nina W102
- Module
- Dual Core Tensilica LX6 CPU ntawm mus txog 240MHz
- 448 KB ROM, 520KB SRAM, 2MB Flash
- WiFi
- IEEE 802.11b mus txog 11Mbit
- IEEE 802.11g mus txog 54MBit
- IEEE 802.11n mus txog 72MBit
- 2.4 GHz, 13 raws
- 16dBm tso zis zog
- 19 dBm EIRP ua
- -96 dBm rhiab heev
- Bluetooth BR / EDR
- Max 7 peripherals
- 2.4 GHz, 79 raws
- Txog li 3 Mbit / s
- 8 dBm tso zis zog ntawm 2/3 Mbit / s
- 11 dBm EIRP ntawm 2/3 Mbit / s
- 88 dBm rhiab heev
- Bluetooth Tsawg Zog
- Bluetooth 4.2 dual-hom
- 2.4GHz 40 raws
- 6 dBm tso zis zog
- 9 dBm EIRP ua
- 88 dBm rhiab heev
- Txog li 1 Mbit /
- MPM 3610 (DC-DC)
- Regulates input voltage los ntawm mus txog 21V nrog qhov tsawg kawg nkaus ntawm 65% kev ua haujlwm @ yam tsawg kawg nkaus load
- Ntau tshaj 85% efficiency @ 12V
- TIAB SA 608A (Crypto Chip)
- Cryptographic co-processor nrog kev ruaj ntseg kho vajtse raws li qhov tseem ceeb cia
- Kev tiv thaiv cia txog li 16 tus yuam sij, daim ntawv pov thawj lossis cov ntaub ntawv
- ECDH: FIPS SP800-56A Elliptic Curve Diffie-Hellman
- NIST tus qauv P256 elliptic nkhaus kev txhawb nqa
- SHA-256 & HMAC hash suav nrog off-chip ntsiab lus txuag / rov qab
- AES-128 encrypt/decrypt, Galois teb multiply rau GCM
- LSM6DSL (6 axis IMU)
- Ib txwm-on 3D accelerometer thiab 3D gyroscope
- Ntse FIFO mus txog 4 KByte raws li
- ± 2 / ± 4 / ± 8 / ± 16g tag nrho teev
- ± 125 / ± 250 / ± 500 / ± 1000 / ± 2000 DPS tag nrho teev
Lub Rooj Tswjhwm Saib
Raws li tag nrho cov Nano daim ntawv boards, Nano 33 IoT tsis muaj lub roj teeb charger tab sis tuaj yeem siv tau los ntawm USB lossis headers.
CEEB TOOM: Arduino Nano 33 IoT tsuas yog txhawb nqa 3.3VI/Os thiab tsis yog 5V ua siab ntev yog li thov xyuas kom koj tsis ncaj qha txuas 5V cov cim rau lub rooj tsavxwm lossis nws yuav puas. Tsis tas li ntawd, tsis zoo li Arduino Nano boards uas txhawb nqa 5V kev ua haujlwm, 5V tus pin tsis muab vol.tage tab sis zoo txuas nrog, los ntawm lub jumper, mus rau USB lub zog nkag.
1.1 Application Examples
Huab cua chaw nres tsheb: Siv Arduino Nano 33 IoT ua ke nrog lub sensor thiab OLED zaub, peb tuaj yeem tsim lub chaw nres tsheb huab cua me me sib txuas lus kub, av noo thiab lwm yam ncaj qha rau koj lub xov tooj.
Cua zoo saib: Cov huab cua tsis zoo yuav ua rau muaj teeb meem loj rau koj txoj kev noj qab haus huv. Los ntawm kev sib sau ua ke Nano 33 IoT, nrog lub sensor thiab saib xyuas koj tuaj yeem ua kom cov huab cua zoo nyob hauv ib puag ncig sab hauv. Los ntawm kev sib txuas cov khoom siv sib dhos rau IoT daim ntawv thov / API, koj yuav tau txais cov nqi ntawm lub sijhawm.
Cua nruas: Txoj haujlwm nrawm thiab lom zem yog tsim lub nruas cua me me. Txuas koj Nano 33 IoT thiab xa koj daim duab kos los ntawm Tsim Web Editor thiab pib tsim neeg ntaus nrog koj lub chaw ua haujlwm ntawm koj xaiv.
Kev ntsuas
Pom zoo rau kev ua haujlwm
| Cim | Kev piav qhia | Min | Max |
| Conservative thermal txwv rau tag nrho lub rooj tsavxwm: | -40 ° C (40 ° F) | 85 ° C (185 ° F) |
Kev siv fais fab
| Cim | Kev piav qhia | Min | Ntaus | Max | Chav tsev |
| VINMax | Cov tswv yim siab tshaj plaws voltage los ntawm VIN pad | - 0.3 Nws | - | 21 | V |
| VUSBmax | Cov tswv yim siab tshaj plaws voltage los ntawm USB connector | - 0.3 Nws | - | 21 | V |
| Pmax | Kev siv hluav taws xob siab tshaj plaws | - | - | TBC | mW |
Muaj nuj nqi Tshajview
Board Topology
| Ref. | Kev piav qhia | Ref. | Kev piav qhia |
| U1 | ATSAMD21G18A maub los | U3 | LSM6DSOXTR IMU Sensor |
| U2 | NINA-W102-00B WiFi / BLE Module | U4 | ATECC608A-MAHDA-T Crypto Chip |
| J1 | Micro USB Connector | PB 1 | IT-1185-160G-GTR Push khawm |
| Ref. | Kev piav qhia | Ref. | Kev piav qhia |
| SJ 1 | Qhib solder choj (VUSB) | SJ 4 | Kaw solder choj (+ 3V3) |
| TP | Kuaj cov ntsiab lus | xx | Lorem Ipsum |
Processor
Tus Txheej Txheem Tseem Ceeb yog Cortex M0 + khiav mus txog 48MHz. Feem ntau ntawm nws cov pins txuas nrog rau sab nraud headers, txawm li cas los xij, qee qhov tau tshwj tseg rau kev sib txuas lus sab hauv nrog lub wireless module thiab on-board sab hauv I2C peripherals (IMU thiab Crypto).
CEEB TOOM: Raws li kev tawm tsam rau lwm cov Arduino Nano boards, pins A4 thiab A5 muaj ib qho kev rub tawm sab hauv thiab lub neej ntawd siv los ua I2C Bus yog li tsis pom zoo siv los ua analog inputs. Kev sib txuas lus nrog NINA W102 tshwm sim los ntawm qhov chaw nres nkoj serial thiab lub npav SPI los ntawm cov pins hauv qab no.
| SAM 21 Pin | SAMD 21 Lub ntsiab lus | NINA Pin | NINA Acronym | Kev piav qhia |
| 13 | PAB 08 | 19 | RESET_N | Rov pib dua |
| 39 | PAB 27 | 27 | GPIO 0 | Nco ntsoov thov |
| 41 | PAB 28 | 7 | GPIO 33 | lees paub |
| 23 | PAB 14 | 28 | GPIO 5 | SPI CS |
| 21 | GPIO 19 | UAS RTS | ||
| 24 | PAB 15 | 29 | GPIO 18 | SIB CLK |
| 20 | GPIO 22 | UAS CTS | ||
| 22 | PAB 13 | 1 | GPIO 21 | SPI YOG |
| 21 | PAB 12 | 36 | GPIO 12 | SPI MOSI |
| 31 | PAB 22 | 23 | GPIO 3 | Processor TX Nina RX |
| 32 | PAB 23 | 22 | GPIO 1 | Processor RX Nina TX |
WiFi / BT Kev Sib Txuas Lus Module
Nina W102 yog raws li ESP32 thiab xa nrog cov software ua ntej tau ntawv pov thawj los ntawm Arduino. Qhov chaws code rau lub firmware yog muaj [9].
CEEB TOOM: Reprogramming lub wireless module lub firmware nrog ib tug kev cai ib tug yuav invalidate raws li xov tooj cua qauv raws li tau ntawv pov thawj los ntawm Arduino, li no yog tsis pom zoo tshwj tsis yog tias daim ntawv thov siv nyob rau hauv private chaw soj nstuam deb ntawm lwm yam khoom siv hluav taws xob thiab cov neeg. Kev siv cov firmware kev cai ntawm xov tooj cua modules yog lub luag haujlwm ntawm tus neeg siv. Qee lub module tus pins txuas nrog rau sab nraud headers thiab tuaj yeem tsav ncaj qha los ntawm ESP32 muab SAMD21 tus pins sib raug zoo yog tri-stated. Hauv qab no yog cov npe ntawm cov teeb liab zoo li no:
| SAM 21 Pin | SAMD 21 Lub ntsiab lus | NINA Pin | NINA Acronym | Kev piav qhia |
| 48 | PB 03 | 8 | GPIO 21 | A7 |
| 14 | PAB 09 | 5 | GPIO 32 | A6 |
| 8 | PB 09 | 31 | GPIO 14 | A5 / SCL |
| 7 | PB 08 | 35 | GPIO 13 | A4/SDA |
3.4 Crypto
Lub crypto nti hauv Arduino IoT boards yog dab tsi ua rau qhov sib txawv nrog lwm cov laug cam uas tsis muaj kev ruaj ntseg vim nws muab txoj hauv kev ruaj ntseg los khaws cov lus zais (xws li ntawv pov thawj) thiab ua kom ceev cov txheej txheem ruaj ntseg thaum tsis txhob nthuav tawm cov lus zais hauv cov ntawv dawb. Qhov chaws rau Arduino Library uas txhawb nqa Crypto muaj [10]
3.5 TSI
Arduino Nano 33 IoT muaj ib qho embedded 6 axis IMU uas tuaj yeem siv los ntsuas kev taw qhia ntawm pawg thawj coj saib (los ntawm kev tshuaj xyuas lub ntiajteb txawj nqus acceleration vector orientation) lossis ntsuas kev poob siab, kev vibration, acceleration thiab kev sib hloov ceev. Qhov chaws rau Arduino Library uas txhawb IMU muaj [11]
3.6 Lub zog ntoo
Board ua haujlwm
Pib Pib - IDE
Yog tias koj xav ua haujlwm rau koj lub Arduino 33 IoT thaum lub sijhawm koj yuav tsum tau nruab Arduino Desktop IDE [1] Txhawm rau txuas Arduino 33 IoT rau koj lub computer, koj yuav xav tau Micro-B USB cable. Qhov no tseem muab lub zog rau lub rooj tsavxwm, raws li qhia los ntawm LED.
Pib - Arduino Web Editor
Txhua Arduino boards, suav nrog qhov no, ua haujlwm tawm ntawm lub thawv ntawm Arduino Web Editor [2], los ntawm kev txhim kho ib qho yooj yim plugin.
Lub Arduino Web Editor yog hosted hauv online, yog li nws yuav ib txwm hloov tshiab nrog cov yam ntxwv tshiab thiab kev txhawb nqa rau txhua lub rooj tsavxwm. Ua raws li [3] pib coding ntawm browser thiab upload koj cov duab kos rau hauv koj lub rooj tsavxwm.
Pib Pib - Arduino IoT Huab
Tag nrho Arduino IoT cov khoom lag luam tau txais kev txhawb nqa ntawm Arduino IoT Huab uas tso cai rau koj nkag mus, teeb tsa thiab txheeb xyuas cov ntaub ntawv sensor, ua rau muaj xwm txheej, thiab ua kom koj lub tsev lossis kev lag luam.
Sampua Sketch
Sample sketches rau Arduino 33 IoT tuaj yeem pom nyob rau hauv "Examples” zaub mov hauv Arduino IDE lossis hauv ntu “Cov ntaub ntawv” ntawm Arduino Pro website [4]
Cov peev txheej online
Tam sim no koj tau dhau los ntawm qhov tseem ceeb ntawm qhov koj tuaj yeem ua nrog lub rooj tsavxwm koj tuaj yeem tshawb nrhiav qhov tsis muaj qhov kawg uas nws muab los ntawm kev tshuaj xyuas cov haujlwm zoo siab ntawm ProjectHub [5], Arduino Library Reference [6] thiab lub khw hauv online [7] qhov twg koj yuav ua kom tiav koj lub rooj tsavxwm nrog sensors, actuators thiab ntau dua.
Board rov qab
Tag nrho cov Arduino boards muaj ib tug built-in bootloader uas tso cai rau flashing lub rooj tsavxwm ntawm USB. Nyob rau hauv cov ntaub ntawv ib tug sketch locks li processor thiab lub rooj tsavxwm tsis ncav cuag tau lawm ntawm USB nws muaj peev xwm mus nkag rau hauv bootloader hom los ntawm ob-tapping lub reset khawm tam sim ntawd tom qab fais fab tuag.
Connector Pinots
USB
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 1 | VUSB | Hwj chim | Fais fab mov Input. Yog hais tias lub rooj tsavxwm yog powered ntawm VUSB los ntawm header qhov no yog ib qho Output
(1) |
| 2 | D- | Qhov txawv | USB cov ntaub ntawv sib txawv - |
| 3 | D+ | Qhov txawv | USB cov ntaub ntawv sib txawv + |
| 4 | ID | Analog | Xaiv lub party/Device functionality |
| 5 | GND | Hwj chim | Hwj chim hauv av |
Lub rooj tsavxwm tuaj yeem txhawb USB hom tswv nkaus xwb yog tias siv los ntawm VUSB tus pin thiab yog tias lub jumper ze rau VUSB tus pin luv.
Headers
Lub rooj tsavxwm nthuav tawm ob lub 15 tus pin connectors uas tuaj yeem ua ke nrog tus pin headers lossis soldered los ntawm castellated vias.
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 1 | D13 | Digital | GPIO |
| 2 | +3V 3 | Hwj chim Tawm | Internally generated hwj chim tso zis rau lwm pab kiag li lawm |
| 3 | AREF | Analog | Analog siv; tuaj yeem siv ua GPIO |
| 4 | A0/DAC0 | Analog | ADC hauv / DAC tawm; tuaj yeem siv ua GPIO |
| 5 | A1 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 6 | A2 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 7 | A3 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 8 | A4/SDA | Analog | ADC hauv; I2C SDA; Yuav siv tau raws li GPIO (1) |
| 9 | A5 / SCL | Analog | ADC hauv; I2C SCL; Yuav siv tau raws li GPIO (1) |
| 10 | A6 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 11 | A7 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 12 | VUSB | Fais fab hauv / tawm | Nquag NC; tuaj yeem txuas nrog VUSB tus pin ntawm USB txuas los ntawm luv luv jumper |
| 13 | RST | Digital Hauv | Active low reset input (duab ntawm tus pin 18) |
| 14 | GND | Hwj chim | Hwj chim hauv av |
| 15 | VIN | Fais fab hauv | Vin Power input |
| 16 | TX | Digital | USART TX; tuaj yeem siv ua GPIO |
| 17 | RX | Digital | USART RX; tuaj yeem siv ua GPIO |
| 18 | RST | Digital | Active low reset input (duab ntawm tus pin 13) |
| 19 | GND | Hwj chim | Hwj chim hauv av |
| 20 | D2 | Digital | GPIO |
| 21 | D3/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 22 | D4 | Digital | GPIO |
| 23 | D5/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 24 | D6/PWM | Digital | GPIO, tuaj yeem siv ua PWM |
| 25 | D7 | Digital | GPIO |
| 26 | D8 | Digital | GPIO |
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 27 | D9/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 28 | D10/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 29 | D11/MOSI | Digital | SPI MOSI; tuaj yeem siv ua GPIO |
| 30 | D12/MISO | Digital | SPI MISO; tuaj yeem siv ua GPIO |
Debug
Nyob rau sab hauv qab ntawm lub rooj tsavxwm, nyob rau hauv kev sib txuas lus module, debug signals yog teem raws li 3 × 2 xeem pads nrog 100 mil suab. Pin 1 yog piav nyob rau hauv daim duab 3 - Connector Positions
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 1 | +3V 3 | Hwj chim Tawm | Internally generated hwj chim tso zis yuav siv tau raws li voltage siv |
| 2 | SWD | Digital | SAMD11 Ib Wire Debug Cov Ntaub Ntawv |
| 3 | SWCLK | Digital Hauv | SAMD11 Tib Hlau Debug Clock |
| 4 | UPDI | Digital | ATMega4809 hloov tshiab interface |
| 5 | GND | Hwj chim | Hwj chim hauv av |
| 6 | RST | Digital Hauv | Active low reset input |
Cov ntaub ntawv siv tshuab
Board Outline thiab Mounting Qhov
Lub rooj tsavxwm ntsuas yog sib xyaw ntawm metric thiab imperial. Imperial ntsuas yog siv los tuav 100 mil pitch grid ntawm kab kab kom tso cai rau lawv haum lub breadboard whereas board length yog Metric. 
Connector Positions
Cov view Hauv qab no yog los ntawm sab saum toj txawm li cas los nws qhia Debug connector pads uas nyob rau sab hauv qab. Highlighted pins yog tus pin 1 rau txhua qhov txuas '
Sab saum toj view: 
Hauv qab view:
Cov ntawv pov thawj
Kev Tshaj Tawm Txog Kev Ua Raws Cai CE DoC (EU)
Peb tshaj tawm raws li peb lub luag haujlwm ib leeg tias cov khoom lag luam saum toj no tau ua raws li cov cai tseem ceeb ntawm EU Cov Lus Qhia hauv qab no thiab yog li tsim nyog rau kev txav mus los dawb hauv kev lag luam suav nrog European Union (EU) thiab European Economic Area (EEA).
Tshaj Tawm Txog Kev Ua Raws Li EU RoHS & REACH 211 01/19/2021
Arduino boards tau ua raws li RoHS 2 Directive 2011/65 / EU ntawm European Parliament thiab RoHS 3 Cov Lus Qhia 2015/863 / EU ntawm Pawg Sab Laj ntawm 4 Lub Rau Hli 2015 ntawm kev txwv tsis pub siv qee yam khoom siv phom sij hauv cov khoom siv hluav taws xob thiab hluav taws xob.
| Tshuaj | Qhov siab tshaj plaws (ppm) |
| Lead (Pb) Hmoob. | 1000 |
| Cadmium (Cd) | 100 |
| Mercury (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Tom ntej: Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl) phthalate (DEHP) | 1000 |
| Tom ntej: Benzyl Butyl Phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Kev zam: Tsis muaj kev zam.
Arduino Boards tau ua raws li tag nrho cov kev cai ntawm European Union Regulation (EC) 1907 / 2006 hais txog Kev Sau Npe, Kev Ntsuam Xyuas, Kev Tso Cai thiab Kev Txwv Cov Tshuaj (REACH). Peb tshaj tawm tsis muaj SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Cov Neeg Sib Tw Cov Ntawv Teev Npe ntawm Cov Khoom Muaj Kev Nyuaj Siab Heev rau kev tso cai tam sim no tso tawm los ntawm ECHA, muaj nyob rau hauv tag nrho cov khoom (thiab kuj pob) nyob rau hauv ntau npaum li cas nyob rau hauv ib tug concentration sib npaug zos los yog siab tshaj 0.1%. Rau qhov zoo tshaj plaws ntawm peb txoj kev paub, peb kuj tshaj tawm tias peb cov khoom tsis muaj ib yam ntawm cov khoom muaj npe nyob rau hauv "Tsev Ntawv Tso Cai" (Annex XIV ntawm REACH cov cai) thiab Cov Khoom Muaj Kev Txaus Siab Siab (SVHC) hauv ib qho tseem ceeb npaum li qhov tau hais tseg. los ntawm Annex XVII ntawm Cov Neeg Sib Tw Cov Npe Tshaj Tawm los ntawm ECHA (European Chemical Agency) 1907/2006/EC.
Kev tsis sib haum xeeb Minerals tshaj tawm
Raws li lub ntiaj teb kev lag luam ntawm cov khoom siv hluav taws xob thiab hluav taws xob, Arduino paub txog peb lub luag haujlwm ntsig txog kev cai lij choj thiab cov cai hais txog kev tsis sib haum xeeb Minerals, tshwj xeeb yog Dodd-Frank Wall Street Reform and Consumer Protection Act, Section 1502. Arduino tsis ncaj qha los yog txheej txheem teeb meem. minerals xws li Tin, Tantalum, Tungsten, los yog kub. Cov khoom tsis sib haum xeeb muaj nyob rau hauv peb cov khoom nyob rau hauv daim ntawv ntawm solder, los yog raws li ib feem ntawm cov hlau alloys. Raws li ib feem ntawm peb qhov kev mob siab rau qhov tsim nyog Arduino tau hu rau cov neeg muag khoom nyob rau hauv peb cov saw hlau los xyuas lawv cov kev ua raws li cov cai txuas ntxiv. Raws li cov ntaub ntawv tau txais los txog tam sim no peb tshaj tawm tias peb cov khoom muaj cov khoom tsis sib haum xeeb los ntawm cov chaw tsis sib haum xeeb.
FCC ceev faj
Ib qho kev hloov pauv lossis kev hloov kho uas tsis tau pom zoo los ntawm tog neeg lub luag haujlwm rau kev ua raws cai tuaj yeem ua rau tus neeg siv txoj cai ua haujlwm ntawm cov khoom siv.
Cov cuab yeej no ua raws li Tshooj 15 ntawm FCC Cov Cai. Kev ua haujlwm yog ua raws li ob yam hauv qab no:
- Cov cuab yeej no yuav tsis ua teeb meem cuam tshuam
- Cov cuab yeej no yuav tsum lees txais kev cuam tshuam tau txais, suav nrog kev cuam tshuam uas yuav ua rau tsis muaj kev ua haujlwm.
FCC RF Radiation Exposure Statement:
- Lub Transmitter no yuav tsum tsis txhob muab tso rau hauv los yog ua haujlwm ua ke nrog lwm tus kav hlau txais xov lossis cov khoom xa tawm.
- Cov cuab yeej no ua raws li cov kev txwv ntawm RF hluav taws xob raug teeb tsa rau qhov chaw tsis muaj kev tswj hwm.
- Cov cuab yeej no yuav tsum tau nruab thiab ua haujlwm nrog qhov tsawg kawg nkaus ntawm 20cm ntawm lub tshuab hluav taws xob thiab koj lub cev.
Lus Askiv: Cov neeg siv phau ntawv rau cov khoom siv xov tooj cua tsis muaj ntawv tso cai yuav tsum muaj cov ntawv ceeb toom hauv qab no lossis sib npaug hauv qhov chaw pom tseeb hauv phau ntawv siv los yog hloov ntawm lub cuab yeej lossis ob qho tib si. Cov cuab yeej no ua raws li Kev Lag Luam Canada daim ntawv tso cai-tsim RSS tus qauv (s). Kev ua haujlwm yog ua raws li ob yam hauv qab no:
- cov cuab yeej no yuav tsis ua rau muaj kev cuam tshuam
- cov cuab yeej no yuav tsum lees txais ib qho kev cuam tshuam, suav nrog kev cuam tshuam uas yuav ua rau lub tshuab ua haujlwm tsis xav tau.
IC SAR Waring:
Cov khoom siv no yuav tsum muab ntsia thiab ua haujlwm nrog qhov nrug tsawg kawg 20 cm ntawm qhov hluav taws xob thiab koj lub cev.
Tseem ceeb: Kev ua haujlwm kub ntawm EUT tsis tuaj yeem tshaj 85 ℃ thiab yuav tsum tsis txhob qis dua -40 ℃. Ntawm no, Arduino Srl tshaj tawm tias cov khoom no ua raws li cov kev cai tseem ceeb thiab lwm yam kev cai ntawm Cov Lus Qhia 2014/53/EU. Cov khoom no raug tso cai siv nyob rau hauv tag nrho EU cov tswv cuab lub xeev.
| Ntau zaus | Maximum tso zis zog (ERP) |
| 863-870 MHz | -3.22dBm |
Cov ntaub ntawv tuam txhab
| Lub tuam txhab npe | Arduino SA. |
| Chaw Nyob | Ntawm Ferruccio Pelli 14 6900 Lugano Switzerland |
Cov ntaub ntawv siv
| Kev siv | Txuas |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Huab) | https://create.arduino.cc/editor |
| Cloud IDE Pib Pib | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino- web-editor-4b3e4a |
| Rooj sab laj | http://forum.arduino.cc/ |
| TIAB SA 21G18 | http://ww1.microchip.com/downloads/en/devicedoc/40001884a.pdf |
| NIAS W102 | https://www.u-blox.com/sites/default/files/NINA-W10_DataSheet_%28UBX- 17065507%29.pdf |
| EC608 | http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf |
| MPM 3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
| NINA Firmware | https://github.com/arduino/nina-fw |
| Lub tsev qiv ntawv ECC608 | https://github.com/arduino-libraries/ArduinoECCX08 |
| LSM6DSL Library | https://github.com/stm32duino/LSM6DSL |
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Library Reference | https://www.arduino.cc/reference/en/ |
| Arduino Khw | https://store.arduino.cc/ |
Kev kho keeb kwm
| Hnub tim | Kev kho dua | Hloov |
| 04/15/2021 | 1 | General datasheet hloov tshiab |
Cov ntaub ntawv / Cov ntaub ntawv
 |
ARDUINO ABX00027 Nano 33 IoT Development Board [ua pdf] Tus neeg siv phau ntawv ABX00027, Nano 33 IoT Development Board |
 |
ARDUINO ABX00027 Nano 33 IoT Development Board [ua pdf] Tus neeg siv phau ntawv ABX00027, Nano 33 IoT Development Board |
 |
ARDUINO ABX00027 Nano 33 IoT Development Board [ua pdf] Tus neeg siv phau ntawv ABX00027 Nano 33 IoT Development Board ABX00027 Nano 33 IoT Development Board |
