RYNOSKIN RSSS-JK0201 DS7 II Python Side Matakai
Torque & Kayan aiki
KAFIN SHIGA
Cire abun ciki daga akwatin. TABBATAR DA DUKAN SASHE NA GABA DOMIN YANA KAN JERIN SAUKI. KARATUN UMARNI A HANKALI. ANA YIWA YANKEWA. ANA SHAWARAR TAIMAKO.
Jerin Sashe
A LURA CEWA HOTUNAN DA SUKE NAN SUN GINU NE AKAN HANYAR FUSKA.
MATAKI NA 1
Fara shigarwa zuwa gaban Fasinja/ gefen dama na abin hawa, Gano wurin gaba, tsakiya, da wuraren hawa na baya (Fig 1).
MATAKI NA 2
Ƙayyade idan abin hawa yana da buɗaɗɗen panel na bene ko rami mai zare a cikin ɓangaren bene
- Motoci masu buɗaɗɗen wurin hawa:
a. Saka (1) Farantin Kwaya 10mm a cikin babban fili mai buɗewa a cikin rukunin bene. Yi layi na goro mai zaren tare da rami a tsakanin ramukan biyu akan walda mai tsunkule, (Fig 2).
b. Zaɓi Bakin Dutsen Fasinja/Dama na Gaba. NOTE: Akwai ƙaramin daraja a Ƙarƙashin Ƙaƙwalwar Cibiyar kuma ƙaƙƙarfan maƙallan Rear yana saman saman. Da fatan za a gano Maɓallan Gaba, Cibiyar, da Rear bisa ga Jerin Sashe.
c. Haɗa Bracket zuwa Plate ɗin Kwaya tare da (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer, da (1) 10mm x 34mm Flat Washer, (Hoto 3). Kada ku matsa kayan aikin.
- Motoci masu ramukan masana'anta a cikin fatun bene:
a. Zaɓi Bakin Dutsen Fasinja/Dama na Gaba. Haɗa Bracket zuwa wurin hawa na gaba (Fig 4) tare da (1) 8mm Hex Bolt, (1) 8mm Lock Washer, da (1) 8mm Flat Washer, (Fig 5). Kada ku matsa kayan aikin.
MATAKI NA 4
Haɗa Bracket ɗin Tallafi zuwa Madaidaicin Dutsen tare da (1) 10mm x 30mm Hex Bolt, (2) 10mm x 20mm Flat Washers, da (1) 10mm Nylon Lock Nut, (Fig 7). Kada ku matsa kayan aikin.
MATAKI NA 5
Maimaita Matakai 2 – 4 don haɗa Fasinja/Cibiyar Dama da Maɓallan Haɗawa na Rear da Brackets Support zuwa tsakiya da wuraren baya, (Figs 8- 9). NOTE: Akwai ƙaramin daraja a Ƙarƙashin Ƙaƙwalwar Cibiyar kuma ƙaƙƙarfan maƙallan Rear yana saman saman. Da fatan za a gano Cibiyoyin Cibiya da Ƙwararrun Raya bisa ga wannan, (Fig 10). Kada ku matsa kayan aikin.
MATAKI NA 6
Zaɓi Kwamitin Gudun Fasinja/Dama.
NOTE: Hukumar Gudun Fasinja/Dama zata sami “P” a gaba. Haɗa allon Gudu zuwa Maƙallan Haɗawa tare da (6) 8mm Combo Bolts, (Hoto 11). MUHIMMI: Kada a zame allon Gudu a kan shimfiɗar katako na Dutsen Bracket, ko lalacewa ga ƙarewar na iya haifar da. Kada ku matsa kayan aikin.
MATAKI NA 7
Level da daidaita Gudun Board da kuma ƙara duk hardware.
MATAKI NA 8
Maimaita Matakai 1-7 don haɗa allon Gudun Direba/Hagu.
MATAKI NA 9
Yi binciken lokaci -lokaci na shigarwa don tabbatar da cewa duk kayan aikin suna da aminci kuma suna da ƙarfi.
Hankali
Don kare hannun jarin ku, kar a yi amfani da kowane nau'in goge ko kakin zuma wanda zai iya ƙunsar abrasives wanda zai iya lalata ƙarshen.
Hakanan ana iya amfani da sabulu mai laushi don tsaftace allon Gudu.
www.rynoskinauto.com.
Taimakon Abokin Ciniki: service@rynoskinauto.com
Takardu / Albarkatu
 |
RYNOSKIN RSSS-JK0201 DS7 II Python Side Matakai [pdf] Jagoran Shigarwa RSSS-JK0201 DS7 II Matakan Side na Python, RSSS-JK0201, DS7 II Matakan Side Python, Matakan Side na Python, Matakan Gefe, Matakai |
