RYNOSKIN
Installation Guide for RYNOSKIN models including: RSSS-JK0201 DS7 II Python Side Steps, RSSS-JK0201, DS7 II Python Side Steps, Python Side Steps, Side Steps, Steps
RYNOSKIN DS7 II Side Steps for 2007-2018 Jeep Wrangler JK 4 Door (excl
File Info : application/pdf, 5 Pages, 696.62KB
DocumentDocumentPYTHON SIDE STEP PART NO. RSSS-JK0201 FITS: 2007-2018 Jeep Wrangler JK 4 Door 90-180 min Cutting Not Required Drilling Not Required Part List Torque & Tools Fastener Size 6mm 8mm 10mm 12mm Tightening Torque (ft-lbs) 7-8.5 18-20 35-40 60-70 Wrench Required 10mm 13mm 16mm 18mm Allen Wrench Required 4mm 5mm 6mm 8mm BEFORE INSTALLATION REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. CUTTING MAY BE REQUIRED. ASSISTANCE IS RECOMMENDED. "D" for Left/Driver Side Front "P" for Right /Passenger Side #1 #2 Driver/Left Side Front Bracket Driver/Left Side Center Bracket A Notch Here #1 #2 A Notch Here Passenger/Right Side Front Bracket #1 #2 Driver/Left Side Rear Bracket Passenger/Right Side Rear Bracket #1: Driver/Left Support Bracket x 3 #2: Passenger/Right Support Bracket x 3 www.rynoskinauto.com Customer Support: service@rynoskinauto.com x6 10mm x 35mm Hex Bolt x6 x6 x6 x12 x6 10mm x 30mm Hex Bolt 10mm x 34mm Flat Washer 10mm x 20mm Flat Washer 10mm Lock Washer x6 x6 x6 x6 10mm Lock Nut 10mm Nut Plate x12 x12 8mm x 35mm Hex Bolt x24 8mm Lock Washer x12 8mm x 28mm Flat Washer 8mm x 25mm Combo Bolt 6mm x 25mm Hex Bolt 6mm x 22mm Flat Washer 6mm Lock Nut PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE PASSENGER SIDE INSTALLATION STEP 1 Start installation toward the front of the Passenger/Right side of the vehicle, Locate the front, center and rear mounting locations (Fig 1). FIG 1 (Fig 1) Passenger/Right mounting locations STEP 2 Determine if the vehicle has an open floor panel or a threaded hole in the floor panel (1) Vehicles with open mounting location: a. Insert (1) 10mm Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the hole in between the pair of holes on the pinch weld, (Fig 2). b. Select the Passenger/Right Front Mounting Bracket. NOTE: There is a small notch at the Bottom of the Center Brackets and the notch of Rear Brackets is at the Top. Please identify the Front, Center and Rear Brackets according to the Part List. c. Attach the Bracket to the Nut Plate with (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm x 34mm Flat Washer, (Fig 3). Do not tighten hardware. (2) Vehicles with factory threaded hole in floor panel: a. Select the Passenger/Right Front Mounting Bracket. Attach the Bracket to the front mounting location (Fig 4) with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Fig 5). Do not tighten hardware. www.rynoskinauto.com Page 1 of 4 5/31/23 (JH) FIG 2 FIG 5 10mm Nut Plate (Fig 2) Passenger/Right front mounting location (Models open mounting location shown) FIG 3 10mm x 35mm Hex Bolt 10mm Lock Washer 10mm x 34mm Flat Washer 10mm Nut Plate (Fig 3) Attach the Passenger/Right Front Mounting Bracket to the Nut Plate FIG 4 Pair of holes on pinch weld Front (Fig4) Passenger/Right front mounting location (Models with threaded insert shown) Front 8mm Hex Bolt 8mm Lock Washer 8mm Flat Washer (Fig5) Attach the Passenger/Right Front Mounting Bracket to the Threaded Hole STEP 3 Select (1) Passenger/Right Support Bracket (#2). Attach the Support Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Fig 6). FIG 6 (2) 6mm Hex Bolts (4) 6mm Flat Washers (2) 6mm Nylon Lock Nuts (Fig 6) Attach (1) Passenger/Right Support Bracket (#2) to the (2) holes in the pinch trim in the front location www.rynoskinauto.com Page 2 of 4 5/31/23 (JH) STEP 4 Attach the Support Bracket to the Mounting Bracket with (1) 10mm x 30mm Hex Bolt, (2) 10mm x 20mm Flat Washers and (1) 10mm Nylon Lock Nut, (Fig 7). Do not tighten hardware. FIG 7 10mm x 30mm Hex Bolt (2) 10mm x 20mm Flat Washers 10mm Nylon Lock Nut (Fig 7) Attach (1) Passenger/Right Support Bracket (#2) to the Front Mounting Bracket STEP 5 Repeat Steps 2 - 4 to attach the Passenger/Right Center and Rear Mounting Brackets and Support Brackets to the center and rear locations, (Figs 89). NOTE: There is a small notch at the Bottom of the Center Brackets and the notch of Rear Brackets is at the Top. Please identify the Center and Rear Brackets according to this, (Fig 10). Do not tighten hardware. FIG 8 Rear (Fig 8) Passenger/Right center mounting location (Model with open mounting location shown) FIG 9 Rear (Fig 9) Passenger/Right rear mounting location (Model with threaded inset shown) FIG 10 Rear Bracket www.rynoskinauto.com Center Bracket (Fig 10) Differentiate the Center and Rear Brackets Page 3 of 4 5/31/23 (JH) STEP 6 Select the Passenger/Right Running Board. NOTE: The Passenger/Right Running Board will have a "P" on the front. Attach the Running Board to the Mounting Brackets with (6) 8mm Combo Bolts, (Fig 11). IMPORTANT: Do not slide Running Board on the Mounting Bracket cradles, or damage to the finish may result. Do not tighten hardware. FIG 11 Front (2) 8mm Combo Bolts (Fig 11) Attach the Passenger/Right Running Board to the Mounting Brackets STEP 7 Level and adjust the Running Board and tighten all hardware. STEP 8 Repeat Steps 1--7 to attach Driver/Left Running Board. STEP 9 Do periodic inspections to the installation to make sure that all hardware is secure and tight. Attention To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Boards. www.rynoskinauto.com Page 4 of 4 5/31/23 (JH)