Danfoss SM 084 Gungurawa Compressors
BAYANI
- A: Lambar samfur
- B: Serial number
- C: Firiji
- D: Supply voltage, Farawa na yanzu & Matsakaicin aiki na yanzu
- E: Matsin sabis na gidaje
- F: Mai cajin masana'anta
Shigarwa da sabis na kwampreso ta ƙwararrun ma'aikata kawai. Bi waɗannan umarnin da aikin injiniya na refrigeration sauti masu alaƙa da shigarwa, ƙaddamarwa, kulawa da sabis.
- Dole ne a yi amfani da na'urar kwampreso kawai don ƙera manufar (s) da kuma cikin iyakar aikace-aikacensa (koma zuwa "iyakan aiki").
- Tuntuɓi jagororin aikace-aikacen da takaddun bayanai da ake samu daga cc.danfoss.com
- A ƙarƙashin kowane yanayi, EN378 (ko wasu ƙa'idodin aminci na gida) dole ne a cika su.
- Ana isar da kwampreso a ƙarƙashin matsin iskar gas na nitrogen (tsakanin mashaya 0.3 da 0.7) don haka ba za a iya haɗa shi ba kamar yadda yake; koma zuwa sashin ''majalisar'' don ƙarin cikakkun bayanai.
- Dole ne a kula da kwampreso da taka tsantsan a cikin matsayi na tsaye (mafi girman saiti daga tsaye: 15°)
Umarni
SH / WSH 090 – 105 – 120 – 140 *- 161* -184*
SM 084 – 090 – 100 – 110 – 112 – 120 – 124 – 147 – 148 – 161 SZ 084 – 090 – 100 – 110 – 120 – 147 – 148 – 161
Wadannan kwampressors na Danfoss na gungurawa suna da kariya daga zafi fiye da kima da kima ta hanyar kariya ta mota ta ciki. Koyaya, ana ba da shawarar mai kariyar sake saitin kayan aiki na waje don kare da'irar daga wuce gona da iri na yanzu.
SM 115 – 125 – 160 – 175 – 185 SZ 115 – 125 – 160 – 175 – 185 iri tare da ma’aunin zafi da sanyio
Wadannan kwamfutoci na Danfoss na gungurawa ana samar da su tare da bimetallic pole guda jefa thermostat wanda ke cikin iskar motsi. Saboda ma'aunin zafi da sanyio na'urar sake saiti ta atomatik, dole ne a sanya shi a cikin da'irar aminci ta kulle tare da sake saitin hannu don sake kunna naúrar. Don kariyar wuce gona da iri, dole ne a yi amfani da kariyar sake saiti mai yawa na waje.
SH180
SM 115 – 125 – 160 – 175 – 185 SZ 115 – 125 – 160 – 175 – 185 iri tare da na’urar lantarki
Wannan Danfoss gungurawa kompressor motor ana kiyaye shi ta tsarin waje wanda ke karewa daga zafi mai zafi da babban zane na yanzu.
SM 115 – 125 – 160 – 175 – 185 SZ 115 – 125 – 160 – 175 – 185 SH180
SH 240 - 295 - 300 - 380 -485
SY 240 - 300 - 380
SZ 240 - 300 - 380
Waɗannan injinan kwamfutoci na Danfoss gungurawa ana kiyaye su ta wani tsari na waje wanda ke ba da kariya daga asarar lokaci, zafi mai zafi da babban zane na yanzu.
Labari:
- Fuskoki……………………………………………………………………………………………….F1
- Mai tuntuɓar kwampreso………………………………………………………………….KM
- Relay mai sarrafawa …………………………………………………………………………………………………
- Safety Kulle fitar da gudu …………………………………………………………………
- Zaɓin ɗan gajeren lokacin zagayowar (minti 3) …………………………………. 180 s
- Kariyar kaya ta waje………………………………………………………
- Canjin matsa lamba mai saukarwa………………………………………………………………
- Babban matsi aminci canji………………………………………………………………………
- Na'urar sarrafawa………………………………………………………………………………………
- Liquid Line Solenoid bawul…………………………………………………………
- Fitar da iskar gas ………………………………………………………….DGT
- Cire haɗin da aka haɗa………………………………………………………………………………….Q1
- Matsakaicin Tsaro na Motoci……………………………………………………………… thM
- Motar damfara………………………………………………………………………………
- Module Kariyar Mota…………………………………………………………………………
- Sarkar thermistor………………………………………………………………………………………
- Maɓallin matsi na aminci…………………………………………………………………………
- Sarrafa da'ira……………………………………………………………………….CC
Duk zane-zanen wayoyi suna tare da zagayowar saukar da famfo
Gabatarwa
Waɗannan umarnin sun shafi SM, SY, SZ, SH & WSH na'urorin gungurawa na Danfoss da ake amfani da su don tsarin kwandishan. Suna ba da mahimman bayanai game da aminci da ingantaccen amfani da wannan samfur.
Gudanarwa da ajiya
- Karɓar da kwampreso da kulawa. Yi amfani da keɓaɓɓun hannaye a cikin marufi. Yi amfani da murfin ɗagawa na kwampreso kuma yi amfani da dacewa da kayan ɗagawa masu aminci.
- Ajiye da jigilar kwampreso a wuri madaidaiciya.
- Ajiye compressor tsakanin -35°C da 50°C.
- Kada a bijirar da kwampreso da marufi zuwa ruwan sama ko yanayi mai lalata.
Matakan tsaro kafin taro
Kada kayi amfani da kwampreso a cikin yanayi mai ƙonewa.
- Yanayin zafin jiki na compressor bazai wuce 50 ° C yayin sake zagayowar ba.
- Dutsen kwampreso a kan shimfidar lebur a kwance tare da gangara kasa da 3°.
- Tabbatar cewa wutar lantarki ta yi daidai da halayen injin kwampreta (duba farantin suna).
- Lokacin shigar da SZ ko SH ko WSH, yi amfani da kayan aiki na musamman da aka tanada don refrigerants na HFC waɗanda ba a taɓa amfani da su ba don CFC ko HCFC refrigerants.
- Yi amfani da bututun jan ƙarfe mai tsafta da bushewar firji da kayan ƙoshin ƙarfe na azurfa.
- Yi amfani da abubuwan tsarin tsafta da bushewar ruwa.
- Bututun da aka haɗa da kwampreso dole ne ya zama mai sassauƙa cikin girma 3 zuwa dampen vibrations.
Majalisa
- A cikin majalisu guda ɗaya na SH, WSH, SM112 - 124 - SM/SZ147 compressor yana buƙatar tsayayyen hawa akan dogo. Yi amfani da matsananciyar sarari daga kayan hawan tandem ko ƙwanƙwaran da aka kawo tare da kwampreso na tandem.
- Sannu a hankali saki cajin riƙewar nitrogen ta tashar schrader.
- Cire gaskets lokacin brazing masu haɗin rotolock.
- Yi amfani da sabbin gaskets koyaushe don taro.
- Haɗa compressor zuwa tsarin da wuri-wuri don guje wa gurɓataccen mai daga danshi na yanayi.
- Kauce wa kayan shiga cikin tsarin yayin yanke tubes. Kada a taɓa huda ramuka inda ba za a iya cire buras ba.
- Braze tare da kulawa sosai ta amfani da fasaha na zamani da bututun iska tare da kwararar iskar iskar nitrogen.
- Haɗa aminci da na'urorin sarrafawa da ake buƙata. Lokacin da ake amfani da tashar schrader don wannan, cire bawul na ciki.
- Kada ku wuce matsakaicin ƙarfin ƙarfi don haɗin gwiwar rotolock:
| Haɗin Rotolock | Ƙunƙarar ƙarfi |
| 1" rotolock | 80 nm |
| 1 1/4 "rotolock | 90 nm |
| 1 3/4" rotolock | 110 nm |
| 2 1/4" rotolock | 130 Nm. |
Gano leda
Kada a taɓa matsawa kewaye da iskar oxygen ko bushewar iska. Wannan zai iya haifar da wuta ko fashewa.
- SM 084 zuwa 185, SY 380, SZ 084 zuwa 185, SZ 380, SH 090 zuwa 184, WSH 090 zuwa 184: Matsa tsarin a gefen HP da farko sannan a gefen LP. Karka bari matsa lamba akan gefen LP ya wuce matsa lamba akan gefen HP tare da mashaya sama da 5. Irin wannan bambancin matsa lamba na iya haifar da lalacewar kwampreso na ciki.
- Kar a yi amfani da rini don gano zubewa.
- Yi gwajin gano zube akan cikakken tsarin.
- Dole ne matsin gwajin kada ya wuce:
Samfura LP gefe HP gefe SY/SZ 240-380 20 bar 32 bar SM/SZ 84-185 25 bar 32 bar SH 180-485 30 bar 45 bar SH / WSH 090 – 184 33 bar 45 bar - Lokacin da aka gano ɗigon ruwa, gyara ɗigon kuma maimaita gano ruwan.
Rashin bushewar ruwa
- Kada kayi amfani da kwampreso don fitar da tsarin.
- Haɗa injin famfo zuwa bangarorin LP & HP.
- Ja saukar da tsarin ƙarƙashin injin injin 500 μm Hg (0.67 mbar) cikakke.
- Kar a yi amfani da megohmmeter ko sanya wuta a kan kwampreso yayin da yake ƙarƙashin injina saboda wannan na iya haifar da lahani na ciki.
Haɗin lantarki
- Kashe kuma ware babban wutar lantarki. Duba leaf don cikakkun bayanai na wayoyi.
- Dole ne a zaɓi duk abubuwan haɗin lantarki kamar yadda ake buƙata na gida da buƙatun kwampreso.
- Koma shafi na 2 don cikakkun bayanan haɗin wutar lantarki.
- Danfoss gungurawa compressors gungurawa kwampreso kawai yana aiki daidai a hanya guda juyi. Matsakaicin layin L1, L2, L3 dole ne a haɗa su gaba ɗaya zuwa tashoshi na kwampreso T1, T2, T3 don guje wa juyawa baya.
- Yi amfani da ø 4.8 mm (3/16 ") screws da ¼" tashoshi don haɗin wutar lantarki. Daure tare da karfin juyi 3 Nm.
- Haɗin thermostat (idan akwai) ¼” AMP-AWE spade connector.
- Dole ne a haɗa da kwampreso zuwa ƙasa tare da dunƙule ƙarshen duniya na 5 mm.
Cika tsarin
- Rike compressor a kashe.
- Cika firiji a cikin lokaci mai ruwa a cikin na'ura ko mai karɓar ruwa. Dole ne cajin ya kasance kusa da yuwuwar cajin tsarin ƙira don guje wa ƙarancin aiki da matsanancin zafi. Karka bari matsa lamba akan gefen LP ya wuce matsa lamba akan gefen HP tare da mashaya sama da 5. Irin wannan bambancin matsa lamba na iya haifar da lalacewar kwampreso na ciki.
- Ajiye cajin firiji ƙasa da iyakar cajin da aka nuna idan zai yiwu. Sama da wannan iyaka; kare damfara daga ruwa ambaliya-baya tare da famfo-saukar sake zagayowar ko tsotsa line accumulator.
- Kar a taɓa barin silinda mai cika da aka haɗa da kewaye.
| Samfurin Compressor | Iyakar cajin firiji (kg) |
| SM/SZ 084, 090, 100 | 8.5 |
| SM/SZ 110, 120 | 10 |
| SM 112, 124, 147 , SZ147 | 7.9 |
| SM/SZ 115, 125 | 11 |
| SM/SZ 148, 160, 161 | 12.5 |
| SM/SZ 175, 185 | 13.5 |
| SY/SZ 240 | 16 |
| SY/SZ 380 | 20 |
| SH/WSH 090 | 5.9 |
| SH / WSH105, 120, 140,161, 184 | 7.9 |
| SH 180, 240, 295, 300 | 13.5 |
| SH380 | 14.5 |
| SH485 | 17 |
Tabbatarwa kafin ƙaddamarwa
Yi amfani da na'urori masu aminci kamar canjin matsi na aminci da bawul ɗin taimako na inji cikin jituwa tare da gabaɗaya da ƙa'idodi na gida da ƙa'idodin aminci. Tabbatar cewa suna aiki kuma an saita su yadda ya kamata. Bincika cewa saituna na maɓalli mai ƙarfi da bawul ɗin taimako ba su wuce matsakaicin matsi na sabis na kowane ɓangaren tsarin ba.
- Ana ba da shawarar maɓalli mai ƙarancin ƙarfi don guje wa aikin injin. Mafi ƙarancin saiti don SM/SY/SZ: 0.5 bar g. Mafi ƙarancin saiti don SH/WSH: mashaya 1.5 g.
- Tabbatar da cewa duk haɗin wutar lantarki an ɗaure su da kyau kuma suna bin ƙa'idodin gida.
- Lokacin da ake buƙatar na'urar bushewa, dole ne a ba da kuzari aƙalla sa'o'i 12 kafin farawa na farko da farawa bayan tsawan lokaci na rufewa don na'urorin dumama nau'in bel (awanni 6 don dumama dumama).
Farawa
- Kada a taɓa fara kwampreso lokacin da ba a cajin firiji.
- Duk bawuloli na sabis dole ne su kasance a cikin buɗaɗɗen matsayi.
- Daidaita matsa lamba HP/LP.
- Karfafa kwampreso. Dole ne ya fara da sauri. Idan compressor bai fara ba, duba daidaiton wayoyi da voltage a kan tashoshi.
- Za a iya gano jujjuyawar ƙarshe ta hanyar abubuwan mamaki; Compressor baya gina matsi, yana da matakin sauti mara kyau da ƙarancin wutar lantarki. A irin wannan yanayin, rufe kwampreso nan da nan kuma haɗa matakan zuwa tashoshi masu dacewa. Yawancin Danfoss gungurawa compressors ana kiyaye su daga jujjuyawar juyi ko dai ta hanyar kariyar jujjuyawar ciki ko ta tsarin kariya ta lantarki ta waje. Za su kashe ta atomatik. SH / WSH 090 zuwa 184 kawai da SM 112, 124, 147, SZ147 ba su da kariyar jujjuyawa. Juyawa baya na tsawon lokaci zai lalata waɗannan compressors.
- Idan mai kare kaya na ciki ya fita (SM/SZ 084, 090, 100, 110, 112, 120, 124, 147, 148, 161 da SH / WSH 090, 105, 120, 140, 161), 184 dole ne ya yi sanyi zuwa 60. Dangane da yanayin zafi, wannan na iya ɗaukar sa'o'i da yawa.
- Idan an buɗe bawul ɗin taimako na matsa lamba na ciki (SY/SZ 240, 300, 380 da SH 380, 485), damfara za ta yi dumi kuma na'urar za ta fita a kan mai kare motar.
Duba tare da kwampreso mai gudana
- Duba zane na yanzu da voltage.
- Duba superheat tsotsa don rage haɗarin slugging.
- Kula da matakin mai a cikin gilashin gani na kimanin mintuna 60 don tabbatar da dawowar mai daidai ga kwampreso.
- Mutunta iyakokin aiki.
- Bincika duk bututu don mummunan rawar jiki. Motsi fiye da 1.5 mm yana buƙatar matakan gyara kamar maƙallan bututu.
- Lokacin da ake buƙata, ana iya ƙara ƙarin firji a cikin lokacin ruwa a cikin ƙananan matsi gwargwadon yiwuwa daga kwampreso. Dole ne compressor ya kasance yana aiki yayin wannan tsari.
- Kar a yi cajin tsarin fiye da kima.
- Kar a taɓa sakin na'urar sanyaya zuwa yanayi.
- Kafin barin wurin shigarwa, gudanar da bincike na gabaɗaya game da tsabta, hayaniya da gano ɗigogi.
- Nau'in rikodi da adadin cajin firiji da yanayin aiki azaman abin dubawa na gaba.
Kulawa
- Matsi na ciki da zafin jiki suna da haɗari kuma suna iya haifar da rauni na dindindin. Masu aikin kulawa da masu sakawa suna buƙatar ƙwarewa da kayan aiki masu dacewa. Yawan zafin jiki na tubing na iya wuce 100 ° C kuma yana iya haifar da ƙonewa mai tsanani.
- Tabbatar cewa ana yin binciken sabis na lokaci-lokaci don tabbatar da amincin tsarin kuma kamar yadda dokokin gida suka buƙata.
Don hana matsalolin da suka shafi tsarin, ana ba da shawarar kiyayewa lokaci-lokaci:
- Tabbatar cewa na'urorin aminci suna aiki kuma an saita su yadda ya kamata.
- Tabbatar cewa tsarin ya zube sosai.
- Bincika zane na compressor na yanzu.
- Tabbatar da cewa tsarin yana aiki ta hanyar da ta dace da bayanan kulawa na baya da yanayin yanayi.
- Bincika cewa duk haɗin wutar lantarki har yanzu suna da kyau sosai.
- Tsaftace kwampreso kuma tabbatar da rashin tsatsa da oxidation akan harsashin kwampreso, bututu da haɗin lantarki.
Garanti
Koyaushe watsa lambar ƙira da lambar serial tare da kowane da'awa filed game da wannan samfurin.
Garanti na samfur na iya zama mara amfani a cikin waɗannan lokuta:
- Rashin farantin suna.
- gyare-gyare na waje; musamman, hakowa, walda, karyewar ƙafa da alamun girgiza.
- Compressor ya buɗe ko ya dawo ba a rufe ba.
- Tsatsa, ruwa ko rini gano ɗigo a cikin kwampreso.
- Amfani da firiji ko mai mai wanda Danfoss bai amince da shi ba.
- Duk wani sabani daga shawarwarin shawarwarin da suka shafi shigarwa, aikace-aikace ko kiyayewa.
- Yi amfani da aikace-aikacen hannu.
- Amfani a cikin yanayin yanayi mai fashewa.
- Babu lambar ƙira ko lambar serial da aka watsa tare da da'awar garanti.
zubarwa
Danfoss ya ba da shawarar cewa kamfanin da ya dace ya sake yin amfani da kwampreso da man kwampreso a wurinsa.
Danfoss ba zai iya karɓar alhakin yuwuwar kurakurai a cikin kasida, ƙasidu da sauran bugu. Danfoss yana da haƙƙin canza kayan sa ba tare da sanarwa ba. Wannan kuma ya shafi samfuran da aka riga aka yi kan oda muddin ana iya yin irin waɗannan sauye-sauye ba tare da wasu canje-canje masu zuwa sun zama dole ba cikin ƙayyadaddun ƙayyadaddun da aka amince da su. Duk alamun kasuwanci a cikin wannan kayan mallakar kamfanoni ne. Danfoss da alamar tambarin Danfoss alamun kasuwanci ne na Danfoss A/S. An kiyaye duk haƙƙoƙi.
Tambayoyin da ake yawan yi
- Tambaya: Za a iya amfani da compressors tare da firigeren daban-daban?
A: Na'am, compressors sun dace da takamaiman firigeren kamar yadda aka ambata a cikin littafin. Tabbatar da bin ƙa'idodi na kowane nau'in firji. - Tambaya: Ana buƙatar kariya ta waje don compressors?
A: Dangane da samfurin, kariya ta waje kamar masu kariyar sake saitin obalawa na hannu ana iya ba da shawarar don abubuwan da suka wuce yanzu. Koma zuwa littafin jagora don takamaiman bayani.
Takardu / Albarkatu
 |
Danfoss SM 084 Gungurawa Compressors [pdf] Umarni SM 084, 090, 100, 110, 112, 120, 124, 147, 148, 161, SZ 084, 090, 100, 110, 120, 147, 148, 161, gungurawa SM 084 Kwamfuta, Compressors |
