Danfoss KoolProg PC Software

Ƙayyadaddun bayanai

• Tallafin samfuran Danfoss: ETC 1H, EETc/EETa, ERC 111/112/113, ERC 211/213/214, EKE 1A/B/C, AK-CC55, EKF 1A/2A, EIM 365, EKE 100, EKC 22x
• Tsarin aiki: Windows 10 ko Windows 11, 64 bit
• RAM: 8 GB RAM
• Hard Drive Space: 200 GB
• Software da ake buƙata: MS Office 2010 da sama
• Interface: USB 3.0

Gabatarwa

Ƙirƙiri da gwada masu sarrafa lantarki na Danfoss bai taɓa zama mai sauƙi kamar sabon software na KoolProg PC ba.
Tare da software KoolProg ɗaya, yanzu zaku iya ɗaukar advantage na sabbin fasalulluka masu fa'ida kamar zaɓin jerin abubuwan da aka fi so, rubuce-rubuce akan layi da kuma shirin layi. files, da saka idanu ko kwaikwaya ayyukan matsayin ƙararrawa. Waɗannan su ne kawai wasu sabbin abubuwan da za su rage lokacin R&D da samarwa da za su kashe don haɓakawa, shirye-shirye, da kuma gwada kewayon Danfoss na masu sarrafa firiji na kasuwanci.
Tallafin samfuran Danfoss: ETC 1H, EETc/EETa, ERC 111/112/113, ERC 211/213/214,
EKE 1A/B/C, AK-CC55, EKF 1A/2A, EIM 365, EKE 100, EKC 22x.
Umurnai masu zuwa zasu jagorance ku ta hanyar shigarwa da amfani da KoolProg® na farko.

Sauke .exe file
Zazzage KoolProgSetup.exe file daga wurin: http://koolprog.danfoss.com

Bukatun tsarin
An yi nufin wannan software don mai amfani guda ɗaya da shawarar tsarin buƙatun kamar ƙasa.

OS	Windows 10 ko Windows 11, 64 bit
RAM	8 GB RAM
HD sarari	200 GB da 250 GB
Software da ake buƙata	MS Offi ce 2010 da sama
Interface	Kebul na USB 3.0

Ba a tallafawa tsarin aiki na Macintosh.
Gudanar da saitin kai tsaye daga uwar garken Windows ko cibiyar sadarwa file ba a ba da shawarar uwar garke ba.

Shigar da software
Danna sau biyu akan gunkin saitin KoolProg®.
Gudun mayen shigarwa kuma bi umarnin kan allo don kammala shigarwar KoolProg®.

Lura: Idan kun ci karo da "gargadin tsaro" yayin shigarwa, da fatan za a danna "Shigar da wannan software ta kowane hali".

Haɗin kai tare da masu sarrafawa

1. Haɗa KoolKey zuwa tashar USB ta PC ta amfani da madaidaicin kebul na USB.
2. Haɗa mai sarrafawa zuwa KoolKey ta amfani da kebul na mu'amala na mai sarrafawa.

1. Haɗa kebul na USB zuwa tashar USB ta PC.
2. Haɗa mai sarrafawa ta amfani da kebul na daban.

HANKALI: Da fatan za a tabbatar cewa an haɗa mai sarrafawa ɗaya kawai a kowane lokaci.

Don ƙarin bayani kan saitin shirye-shirye file zuwa mai sarrafawa ta amfani da KoolKey da Maɓallin Shirye-shiryen Mass don Allah a duba hanyoyin haɗin yanar gizo: KoolKey (EKA200) da Maɓallin Shirye-shiryen Mass (EKA201).

Fara shirin

 

 

Dama

• Masu amfani da kalmar sirri suna da damar yin amfani da duk fasalulluka.
• Masu amfani waɗanda ba tare da kalmar wucewa ba suna da iyakataccen damar shiga kuma suna iya yin amfani da fasalin 'Kwafi zuwa mai sarrafawa' kawai.

Saita sigogi

Wannan fasalin yana ba ku damar saita saitunan sigogi don aikace-aikacenku.
Danna ɗaya daga cikin gumakan da ke gefen dama don ƙirƙirar sabon saiti a kashe layi, don shigo da saituna daga mai haɗawa ko don buɗe aikin da aka rigaya ya ajiye.
Kuna iya ganin ayyukan da kuka ƙirƙira a ƙarƙashin “Buɗe saitin kwanan nan file".

Sabo
Ƙirƙiri sabon aiki ta zaɓi:

• Nau'in mai sarrafawa
• Lambar sashi (lambar lamba)
• PV (samfurin sigar) lamba
• SW (software) sigar

Da zarar kun zaɓi a file, kuna buƙatar sunan aikin. Danna 'Gama' don ci gaba zuwa view kuma saita sigogi.

Lura: Madaidaitan lambobi kawai suna samuwa don zaɓar daga cikin filin "Lambar Lamba". Don yin aiki ba tare da layi ba tare da lambar lambar da ba ta dace ba (lambar lambar abokin ciniki), yi amfani da ɗayan hanyoyin biyu masu zuwa:

1. Haɗa mai sarrafa lambar lamba ɗaya tare da KoolProg ta amfani da Ƙofar, kuma yi amfani da "Shigo da saituna daga Mai sarrafawa" don ƙirƙirar saiti. file daga gare ta.
2. Yi amfani da fasalin "Buɗe" don buɗe abin da aka ajiye a cikin gida file a kan PC ɗin ku na lambar lamba ɗaya kuma ƙirƙirar sabo file daga gare ta.

Sabuwa file, wanda aka ajiye akan PC ɗinku na gida, ana iya samun dama ga layi a nan gaba ba tare da haɗa mai sarrafawa ba.

Shigo da saituna daga mai sarrafawa
Yana ba ku damar shigo da tsari daga mai haɗawa zuwa KoolProg kuma don canza sigogi a layi.
Zaɓi "Shigo da saituna daga mai sarrafawa" don shigo da duk sigogi da cikakkun bayanai daga mai haɗawa zuwa PC.

Bayan "An kammala shigo da kaya", ajiye saitin da aka shigo dashi file ta hanyar samar da file suna a cikin akwatin saƙo mai tasowa.

Yanzu ana iya aiki da saitunan sigina akan layi kuma ana iya rubuta su zuwa ga mai sarrafawa ta latsa "Export" . Yayin aiki a layi, ana nuna mai sarrafawa da aka haɗa yayi launin toka kuma ba a rubuta ƙimar sigina zuwa mai sarrafawa har sai an danna maɓallin fitarwa.

Bude

Umurnin "Buɗe" yana ba ku damar buɗe saiti fileAn riga an adana shi zuwa kwamfutar. Da zarar an danna umarnin, taga zai bayyana tare da jerin saitunan da aka adana files.
Ana adana duk ayyukan anan cikin babban fayil: “KoolProg/Configurations” ta tsohuwa. Kuna iya canza tsoho file ajiye wuri a cikin "Preferences" .
Hakanan zaka iya buɗe saitin files da ka karɓa daga wani tushe kuma ka adana a kowace babban fayil ta amfani da zaɓin bincike. Lura cewa KoolProg yana goyan bayan da yawa file Formats (xml, cbk) don
daban-daban masu kula. zaɓi saitin da ya dace file tsarin mai sarrafa da kake amfani da shi.

Lura: tsarin .erc / .dpf files na ERC/ETC mai sarrafa ba a bayyane a nan. An .erc ko .dpf file Ana iya buɗewa a kan PC ɗinku ta ɗayan hanyoyi masu zuwa:

1. Zaɓi "Sabon Project" kuma tafi gaba ɗaya zuwa jerin sigogi view na samfurin mai sarrafawa iri ɗaya. Zaɓi maɓallin Buɗe don lilo da buɗe .erc/.dpf file akan PC naka.
2. Zaɓi "Loda daga mai sarrafawa" idan an haɗa ku zuwa mai sarrafawa iri ɗaya akan layi kuma je zuwa jerin sigogi. view. Zaɓi Buɗe maɓallin don bincika .erc/.dpf da ake so file kuma view yana cikin KoolProg.
3. Zaɓi "Buɗe" don buɗe kowane .xml file na mai sarrafawa iri ɗaya, isa lissafin siga view allon, sannan zaɓi maɓallin Buɗe don lilo kuma zaɓi .erc/.dpf file ku view kuma gyara waɗannan files.

Samfurin mai sarrafawa (kawai don AK-CC55, EKF da EIM):
Wannan yana ba ku damar shigo da ƙirar mai sarrafawa (.cdf) a layi kuma samar da bayanai a KoolProg. Wannan zai baka damar ƙirƙirar saiti file offline ba tare da an haɗa mai sarrafawa zuwa KoolProg ba. KoolProg na iya shigo da ƙirar mai sarrafawa (.cdf) da aka ajiye zuwa PC ko kowace na'urar ajiya.

Mayen saiti mai sauri (kawai don AK-CC55 da EKC 22x):
Mai amfani zai iya tafiyar da saiti mai sauri duka a kashe-layi da kan layi don saita mai sarrafawa don aikace-aikacen da ake buƙata kafin matsawa zuwa cikakkun saitunan sigina.

Maida saitin files (kawai don AK-CC55 da ERC 11x):
Mai amfani zai iya canza saitin files daga sigar software ɗaya zuwa wani nau'in software na nau'in mai sarrafawa iri ɗaya kuma yana iya canza saitunan daga hanyoyi biyu (ƙananan sigar SW mafi girma kuma mafi girma zuwa ƙananan sigar SW.

1. Bude saitin file wanda ke buƙatar canzawa a cikin KoolProg a ƙarƙashin "Set parameter".
2. Danna kan canza saitin .
3. Zaɓi sunan aikin, lambar lambar da sigar SW / sigar samfurin saitin file wanda ke buƙatar ƙirƙirar kuma danna Ok.
4. Za a nuna saƙo mai faɗowa tare da taƙaitaccen juzu'i a ƙarshen tuba.
5. Maida file Ana nunawa akan allon. Duk wani ma'auni mai digon orange yana nuna cewa ƙimar wannan siga ba ta kwafi daga tushe file. An ba da shawarar sakeview wadancan sigogi kuma yin canje-canjen da suka dace kafin rufewa file, idan an buƙata.

Kwafi zuwa na'ura

Anan zaka iya kwafi saitin files zuwa mai haɗawa da haɓaka firmware mai sarrafawa. Siffar haɓaka firmware tana samuwa kawai don ƙirar mai sarrafawa da aka zaɓa kawai.

Kwafi saitin files: Zaɓi saitin file kuna son yin shiri tare da umarnin "BROWSE".
Kuna iya ajiye saiti file a cikin "Fiyayyen Files" ta danna maɓallin "Saita azaman Favourite". Za a ƙara aikin zuwa lissafin kuma za'a iya samun dama ga sauƙi daga baya.
(Danna gunkin sharar don cire aikin daga lissafin).
Da zarar ka zaɓi saiti file, mahimman bayanan da aka zaɓa file ana nunawa.

Haɓaka firmware (kawai don AK-CC55 da EETa):

1. Shigar da firmware file (Bin file) kana so ka shirya - firmware da aka zaɓa file Ana nuna cikakkun bayanai a gefen hagu.
2. Idan firmware da aka zaɓa file ya dace da mai haɗawa, KoolProg yana kunna maɓallin farawa kuma zai sabunta firmware. Idan bai dace ba, maɓallin farawa ya kasance a kashe.
3. Bayan nasarar sabunta firmware, mai sarrafawa zai sake farawa kuma yana nuna bayanan da aka sabunta na mai sarrafawa.
4. Wannan fasalin yana iya samun cikakkiyar kariya ta kalmar sirri. Idan KoolProg yana kare kalmar sirri, to lokacin da kake bincika firmware file, KoolProg yana faɗakar da kalmar sirri kuma zaka iya loda firmware kawai file bayan shigar da kalmar sirri daidai.

Sabis na kan layi

Wannan yana ba ku damar saka idanu kan aikin mai sarrafawa na ainihi yayin da yake gudana.

• Kuna iya sa ido kan abubuwan da aka shigar da su.
• Kuna iya nuna ginshiƙi na layi dangane da sigogi da kuka zaɓa.
• Kuna iya saita saituna kai tsaye a cikin mai sarrafawa.
• Kuna iya adana sigogin layi da saitunan sannan ku bincika su.

Ƙararrawa (kawai na AK-CC55):
A ƙarƙashin shafin "Ƙararrawa", mai amfani zai iya view ƙararrawa masu aiki da tarihin da ke cikin mai sarrafawa tare da lokaci stamp.

Matsayin IO da Sauke Manual:
Mai amfani na iya samun wucewa nan takeview na abubuwan da aka tsara da abubuwan da aka tsara da kuma matsayinsu a ƙarƙashin wannan rukunin. Mai amfani zai iya gwada aikin fitarwa da na'urorin lantarki ta hanyar sanya mai sarrafawa cikin yanayin juyewar hannu da sarrafa kayan sarrafawa da hannu ta hanyar kunna su ON da KASHE .

Charts na Trend
Shirin yana adana bayanai kawai idan an duba akwatin "Ajiye ginshiƙi".
Idan kana son adana bayanan da aka tattara a cikin wani file tsarin, yi amfani da umarnin "Ajiye As". Wannan yana baka damar adana bayanai a cikin .csv/.png file tsari.
Bayan ajiye hoto, ginshiƙi na iya zama viewed daga baya a zaba file tsari.

Tallafin mai sarrafawa wanda ba a sani ba

(Sai don masu kula da ERC 112 & ERC 113)

Idan an haɗa sabon mai sarrafawa, bayanan wannan bayanan bai riga ya kasance a cikin KoolProg ba, amma har yanzu kuna iya haɗawa da mai sarrafawa a cikin yanayin kan layi. Zaɓi "Shigo da saituna daga na'urar da aka haɗa"
ko "Sabis na kan layi" zuwa view lissafin siga na mai haɗawa. Duk sabbin sigogin mai sarrafa da aka haɗa za a nuna su a ƙarƙashin rukunin menu daban ”Sabbin Sigai”. Mai amfani zai iya shirya saitunan siga na mai haɗawa da adana saitin file akan PC zuwa shirin taro ta amfani da "Shirye-shiryen EKA 183A (Lambar lamba 080G9740)".

Lura: saitin da aka ajiye file halitta ta wannan hanya ba za a iya sake buɗewa a KoolProg.

Da fatan za a tuntuɓi wakilin tallace-tallace mafi kusa don ƙarin taimako.

Kudin hannun jari Danfoss A/S Climate Solutions
• danfoss.com • +45 7488 2222

Duk wani bayani, gami da, amma ba'a iyakance ga bayanin zaɓi na samfur, aikace-aikacen sa ko amfani da shi ba, ƙirar samfur, nauyi, girma, iyawa ko duk wani bayanan fasaha a cikin ƙasidar kasida, tallace-tallace, da dai sauransu kuma ko an samar da shi a rubuce, da baki, ta hanyar lantarki, akan layi ko ta hanyar zazzagewa, za a yi la'akari da bayanai, kuma yana ɗaure kawai idan kuma har zuwa iyakar tabbatarwa ko yin oda a fayyace. Danfoss ba zai iya karɓar kowane alhakin yuwuwar kurakurai a cikin kasida, kasidu, bidiyo da sauran kayan Danfoss yana da haƙƙin canza samfuransa ba tare da sanarwa ba. Wannan kuma ya shafi samfuran da aka ba da oda amma ba a isar da su ba muddin ana iya yin irin waɗannan sauye-sauye ba tare da canje-canje don ƙira, dacewa ko aikin samfurin ba. Duk alamun kasuwancin da ke cikin wannan kayan mallakar Danfoss A/S ne ko kamfanonin rukunin Danfoss. Danfoss da tambarin Danfoss alamun kasuwanci ne na Danfoss A/S. An kiyaye duk haƙƙoƙi.

Tambayoyin da ake yawan yi

• Tambaya: Zan iya gudanar da wannan software akan tsarin aiki na Macintosh?
  A: A'a, wannan software tana dacewa da Windows 10 ko Windows 11 kawai.
• Tambaya: Menene zan yi idan na ci karo da gargaɗin Tsaro yayin shigarwa?
  A: Danna kan "Shigar da wannan software na direba" don ci gaba da shigarwa.

Takardu / Albarkatu

Danfoss KoolProg PC Software [pdf] Jagorar mai amfani KoolProg PC Software, PC Software, Software

Magana

• Manual mai amfani