ENGO CONTROLS ECAM-L2 WiFi Smart Floodlight Camera User Guide

Safety Information
Use the product in compliance with national and EU regulations.
Installation should only be done by a qualified person following the regulations.

Installation of the Camera in the App

STEP 1 – DOWNLOAD ENGO SMART APP: Download the
ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.

STEP 2 – REGISTER THE NEW ACCOUNT: Register a new account by following the steps provided in the app.
STEP 3A – CONNECT CAMERA TO WI-FI- Connection via
Bluetooth: Follow the instructions in the app to connect the camera to Wi-Fi via Bluetooth.

STEP 3B – CONNECT CAMERA TO WI-FI- Connection via QR
Code: Connect the camera to Wi-Fi by scanning the QR code provided in the app.

Frequently Asked Questions (FAQ):

Q: What is the maximum storage capacity supported for the microSD card?
A: The camera supports microSD cards up to 256GB capacity.

Technical specification

Power supply 230V AC

Communication Wi-Fi 2.4GHz
Lumen 2500 – 3000lm

Resolution 4Mpx 2560*1440P
Local storage

Micro SD(Max 256GB)- card not included
Minimum requirements of a microSDXC card

-full HD speed class – C10/U1/V10
IP protection class IP65

Dimmension [mm] 283 x 133 x 184

Product Compliance

This product complies with the following EU Directives: 2014/53/EU, 2011/65/EU.

Introduction

The outdoor camera offers Full HD 4MP resolution and a wide 108° viewing angle. The built-in LED lamp with adjustable brightness effectively illuminates the monitored area. Thanks to the motion detection function, the camera reacts to any unwanted movements. The device has two-way audio communication with noise reduction. The camera is equipped with a memory card slot with a capacity of up to 256GB. The camera is suitable for a wide temperature range, from -10°C to +50°C, making it suitable for all conditions. In addition, thanks to the push notification function, users can receive instant alerts via the Engo Smart app.

Product features

Safety Information
Use in accordance with national and EU regulations. Use the device only as intended. Installation must be carried out by a qualified person in accordance with national and EU regulations.

Installation

Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions.

WARNING
For the entire installation, there may be additional protection requirements, which the installer is responsible for (e.g., installation of an additional differential pressure overflow valve).

Camera description

LED lamps
Light sensor
Camera lens
Microphone
Loudspeaker
Moisture protection
Reset button
Micro SD slot

Installation of the camera in the app
Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device.

STEP1 – DOWNLAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.
STEP 2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:
1. Click „Sign Up” to create new account.
2. Enter your e-mail address to which the verification code will be sent.
3. Enter the verification code received in the email.
4. Then set the login password.
STEP 3A – CONNECT CAMERA TO WI-FI- Connection via Bluetooth
After installing the app and creating an account:
1. On your mobile device, make sure the ENGO Smart has access to permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you want to assign the device.
2. Make sure the camera is powered on. Then press and hold the button on the back of the camera for approximately 5 seconds, until the beep. The blue LED on the front of the unit will then start flashing. The pairing mode is enabled.
3. In the app, select:„Add Device”.
4. After finding the camera, go „Add”
5. Select the Wi-Fi network in which the camera will operate and enter the password of this network.
6. Wait for the app to configure the device with the selected Wi-Fi network.
7. Go „DONE”.
8. The camera has been installed and displays the main interface.

STEP 3B – CONNECT CAMERA TO WI-FI- Connection via QR Code

After installing the app and creating an account:

On your mobile device, make sure the ENGO Smart has access to permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you want to assign the device.
Make sure the camera is powered on. Then press and hold the button on the back of the camera for approximately 5 seconds, until the beep. The blue LED on the front of the unit will then start flashing. The pairing mode is enabled.
In the app, select: „Add Device”.

Select „Camera & Lock”.
Find and click on the Wi-Fi camera in the device list
Then go „Next”.

Select the Wi-Fi network in which the camera will operate and enter the password of this network.
Point the camera at the QR code displayed in the app, click „I heard the sound” after the beep.
Wait for the app to configure the device with the selected Wi-Fi network.

Go „DONE”.
Go „DONE”.
The camera has been installed and displays the main interface.

Factory reset

To restore the default settings of the camera, hold down the Reset button for about 5 seconds until a beep sounds. Then release the button. The camera will restart, restore the default (factory) settings and be ready to be added to the application again.

Documents / Resources

ENGO CONTROLS ECAM-L2 WiFi Smart Floodlight Camera [pdf] User Guide
ECAM-L2, ECAM-L2 WiFi Smart Floodlight Camera, ECAM-L2, WiFi Smart Floodlight Camera, Smart Floodlight Camera, Floodlight Camera, Camera

References

User Manual

ENGO CONTROLS ECAM-L2 WiFi Smart Floodlight Camera

Product Usage Instructions