Manuale di l'utente di u modulu di lettura RFID multiprotocolu Hewei Electronic Technology HW58R12-WBDB

Product Specification Product
Modellu di produttu: HW58R12-WBDB/HW59R12-XYLSProduct
Data | Versione | Preparazione | Verificatu | Change content | Rimarche |
24/07/11 | V1.0 | Xiaobing XU | Wang Hanping | Original Drafting | |
Immagine di u produttu:


Pin 1 | Pin 2 | Pin 3 | Pin 4 | Pin 5 |
VCC | GND | RXD | TXD | GND |

Features è Funzioni
- This module is a 13.56MHz RFID read/write module developed based on a multi-protocol readerchip;The reader chip supports ISO/IEC 14443 Type A/Type B protocols. Supports mobile payment applications such as Apple Pay and Samsung Pay. Supports P2P passive initiator mode under ISO/IEC 18092. Supports ISO/IEC 15693 protocol. Complies with EMV 3.0/3.1 certification, including electrical, protocol, and mobile compatibility tests. The module comes pre-integrated with operational commands for reading Mifare1 S50/S70, Mifare UltraLight, MifareDESFire, CPU cards, and second-generation Chinese resident ID cards.
- Ampia operazione voltage range: 5V–24V;
Supports RS232 serial communication with adjustable baud rate; - Automatically detects card presence and outputs data via serial port;
- Supports Low Power Card Detection (LPCD);
- LED Indicator Light Prompt.
Specificazioni tecniche
Nome di u produttu | Multi-protocol RFID Reader Module |
Product Model | HW58R12-WBDB/HW59R12-XYLS |
Dimensioni di u produttu | 65 * 42 mm |
Ambiente operativu | Operating Temperature: -40 to 85℃Maximum Humidity: 5%~95% RH, non-condensing and non-freezing |
Operating frequency | 13.56 MHz |
Contactless Card | Contactless smart cards supporting ISO/IEC 14443 Type A/Type B protocols Contactless smart cards compliant with ISO/IEC 15693 protocol |
Card Reading Distance | ≤ 4 cm |
Metudu di cumunicazione | RS232 serial communication, transmission rate: 19200 bps |
Alimentazione elettrica | DC 12V, supports input range of 5~ 24V |
Cunsumu d'energia | Standby: <0.3W |
Indicatore | Power indicator light |
Altre Funzioni | Provides interface functions or interface command sets, supports custom development. |
Conformal coating follows the following standards:
- Spray coating thickness: 0.1-0.3 mm, with a cured thickness of 40-60 µm.
- Conformal coating bubble standards: Bubbles are allowed on the plastic body or insulating parts of components, and small bubbles within the coating are acceptable. Only a single bubble enclosing a single part of a conductor is acceptable; bubbles between the component leads are not acceptable.
- Exposed copper with tin plating, connectors, and power components should not be coated with conformal coating.
- Components within 3 mm around the connectors do not require conformal coating, but a clear isolation strip of conformal coating must be present around the connectors.
- No conformal coating is allowed within a 5 mm diameter of positioning holes, and holes should not be filled.
- All IC component leads must be coated with conformal coating, and there should be visible traces of conformal coating on the body.
Salt Spray Testing is conducted in accordance with the following standards:
Dichjarazione FCC
- stu dispusitivu ùn pò causari interferenza dannusu.
- stu dispusitivu deve accettà ogni interferenza ricevuta, cumpresi interferenza chì pò causà operazione indesiderata.
Nota: Stu equipamentu hè statu pruvatu è truvatu cum'è i limiti per un dispositivu digitale di Classe B, in cunfurmità cù a parte 15 di e Regule FCC. Questi limiti sò pensati per furnisce una prutezzione raghjone contr'à l'interferenza dannosa in una stallazione residenziale. Stu equipamentu genera usi è pò irradià energia di freccia radio è, se ùn hè micca stallatu è utilizatu in cunfurmità cù l'istruzzioni, pò causà interferenza dannosa à e cumunicazioni radio. Tuttavia, ùn ci hè micca guaranzia chì l'interferenza ùn accade micca in una stallazione particulare. Se l'apparecchiatura provoca interferenza dannosa à a ricezione di a radio o di a televisione, chì pò esse determinata spegnendu è accendendu l'equipaggiu, l'utilizatore hè incuraghjitu à pruvà à corregge l'interferenza cù una o più di e seguenti misure:
- Riorientate o rilocate l'antenna di ricezione.
- Aumente a separazione trà l'equipaggiu è u ricevitore.
- Cunnette l'equipaggiu in una presa in un circuitu diversu da quellu à quale hè cunnessu u ricevitore.
- Cunsultate u rivenditore o un tecnicu espertu di radio/TV per aiutu.
Cambiamenti o mudificazioni chì ùn sò micca appruvati espressamente da a parte rispunsevuli di u cumplimentu puderanu annullà l'autorità di l'utilizatore per operà l'equipaggiu.
Dichjarazione di l'esposizione à a radiazione FCC
Stu dispusitivu hè conforme à i limiti di esposizione à a radiazione RF di FCC stabiliti per un ambiente incontrolatu. Stu trasmettitore ùn deve micca esse situatu o operatu in cunghjunzione cù qualsiasi altra antenna o trasmettitore.
Stu dispositivu deve operà cun una distanza minima di 20 cm trà u radiatore è u corpu di l'utente

Documenti / Risorse
![]() |
Modulu di lettura RFID multiprotocolu Hewei Electronic Technology HW58R12-WBDB [pdfManuale di u pruprietariu HW58R12-WBDB, HW58R12-WBDB Multi Protocol RFID Reader Module, Multi Protocol RFID Reader Module, RFID Reader Module, Reader Module, Module |