RossMax TG250/TG380 Thermometer Instruction Manual

RossMax TG250

INSTRUCTION MANUAL

Rossmax Digital Medical Thermometer

Rossmax Digital Medical Thermometer
Model: TG250/TG380
www.rossmax.com

Introduction

The Digital Medical Thermometer provides quick, highly accurate reading over the human body temperature range. Please read the instructions completely first.

The quality of the thermometer has been verified and conforms to the provisions of the EC council directive 93/42/EEC (Medical Device Directive) Annex I essential requirements and applied harmonized standards. EN 12470-3: 2000 /A1: 2009 Clinical thermometers-Part 3: Performance of compact electrical thermometers (non-predictive and predictive) with maximum device.

Attention: Consult the accompanying documents. Please read this manual carefully before use. Please be sure to keep this manual.

Introduction

How to Use

1.To push the On/Off button by the display window. The display will
read

for 2 seconds and beep sound will be heard.

2. Releasing the on/off button, last measured temperature will be shown for about 2 seconds. Then shows the self-test temperature 37.0°C(98.6°F) , and then Lo°C (Lo°F) displays.

3. Wipe or dip the probe with alcohol for disinfection. Position the probe in oral, rectal or axillary site.

4. Once the degree sign °C (°F) on the display has stopped flashing (usually within 10 to 40 seconds), a Beep signal will sound for approx. 10 times, the measured temperature is shown on LCD window. The temperature reading will not change after the unit is removed from testing position. If the temperature <37.8°C(100.0°F ). the buzzer will alarm “Bi—Bi—Bi—Bi—”. If the temperature ≥ 37.8°C (100.0°F). the buzzer whose frequency is higher will alarm “Bi-Bi-Bi—-Bi-Bi-Bi–” about 10 times rather than”Bi—Bi—Bi—Bi—”

5. The unit will automatically turn off in 10 minutes for energy-saving. However, to prolong the life of the battery, it is suggested to press the On/Off button to turn the unit off once the measurement is done.

6. Please dispose of any used battery and the thermometer according
to the local regulations.

Note: After step 2, if the room temperature is greater than 32.0°C (89.6°F ), it will be displayed the room temperature.

Note: Usage of the probe cover may result in a 0.1°C(0.2°F) difference from actual temperature.

Note: To clean the probe before and after using the thermometer to ensure an accurate reading and avoid cross contamination approximately.

Oral Use

Place the probe well under the patient’s tongue. Confirm the patient to keep his mouth closing for about 20 seconds.

Do not drink hot or cold fluids, exercise, and smoke or perform other activities prior to a reading. These activities will raise or lower temperature readings when compared to your normal, average temperature.

Axillary Use

Tightly place probe in the patient’s armpit for about 30 seconds.

  • Please ensure the close contact between the probe and the armpit of the baby or children.

Rectal Use

Always uses probe cover when taking rectal measurements.

  1. Commonly used for young children when it is difficult to take an oral or axillary temperature.
  2. Lubricate with a water-soluble gel. Do not use petroleum jelly.
  3. Gently insert the probe tip no more than 1.5-2 cm into the rectum for about 10 seconds. Do not force the tip into the rectum if resistance is encountered.
  4. Disinfect the thermometer after use. Refer to “cleaning and disinfection“section.

ºC /ºF Switchable

Temperature readings are available in the Fahrenheit or Celsius scale (°C / °F; located in the right of LCD.) With the unit off, press and hold the On/Off Button for approximately 4 seconds to change the current setting.

Battery Replacement

  1. When the BATTERY SIGN appears on the upper right corner of the LCD, the battery is exhausted and needs replacement.
  2. Pull the battery cover off in the direction shown below.
  3. Pull out the battery with a sharp objects such as pen. Keep exhausted battery from reaching by the children.
  4. Place a new 1.5V D.C. button size battery type SR41 or LR41 or equivalent in the chamber with positive side faced up and negative side faced down.
  5. Install the battery cover back.
Battery Replacement

Display on the LCD

Display on the LCD

M: Last measured temperature.
BATTERY SIGN: When the BATTERY SIGN appears on the upper right corner of the LCD, the battery is exhausted and needs replacement.

Troubleshooting

Troubleshooting

Cleaning and Disinfection

  1. Clean the unit by wiping it with a dry cloth and sterilize the probe with ethyl alcohol.
  2. Don’t let the unit contact any chemical thinner.
  3. Do not soak the display in water.

Caution

  • Do not bend, drop or twist the thermometer. It is not shockproof.
  • Do not boil probe for disinfect.
  • Do not store the unit under direct sunlight, at a high temperature, in high humidity or dust. Neither store the unit under the sunlight, nor at the high temperature or humidity.
  • Do not disassemble. See BATTERY REPLACEMENT to replace battery.
  • Avoid strong electromagnetic interference such as microwave ovens and cell phones.
  • Please be noticed to keep the probe dry before putting the thermometer into the carry case.
  • The thermometer contains small parts (battery, etc.) that can be swallowed by children. Therefore never leave the thermometer unattended to children.
  • The thermometer should be cleaned after measurement no matter the probe cover has been installed or not.
  • Keep battery away from children. Harmful is swallowed.
  • Battery should not be charged or placed into extreme heat as it may explode.
  • Do not use the thermometer in ear. Intended use is for oral, axillary and rectal measurement.
  • Use of the probe cover may result in a 0.1ºC(0.2ºF) discrepancy from actual temperature.
  • Remove battery from the thermometer when not in operation for a long time.
  • If the unit is stored in an extreme environment before measurement, please make sure it has been firstly adapted in the room temperature, so that the unit can be measured normally.
  • Please note that this is a home healthcare product only, and it is not intended to serve as a substitute for the advice of a physician or medical professional.
  • Do not use this device for diagnosis or treatment of any health problem on disease. Measurement results are for reference only. Contact your physician if you have or suspect any medical problems. Do not change your medications without the advice of your physician or healthcare professional.
  • This device may not meet its performance specification if stored or used outside temperature and humidity ranges specified in specifications.
  • If this device is used according to the operations instruction, periodic re-calibration is not required. If you still have questions, please send the device to dealers.
  • Please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at your local retailer or at appropriate collection points provided in your country.
  • This device is for oral, axillary and rectal use only.
  • High, prolonged fever requires medical attention especially for young children. Please contact your physician.
  • For save reason, during children’s temperature measurement, please keep them from crying, walking, talking and any related dangerous activities.

Specifications

Specifications
EMC guidance and manufacturer’s declaration
Guidance and manufacturer
Guidance
Recommended separation distance

Warranty

This instrument is covered by a 5 year guarantee from the date of purchase, batteries and accessories are not included. The guarantee is valid only on presentation of the guarantee card completed by the dealer confirming date of purchase or the receipt. Opening or altering the instrument invalidates the guarantee. The guarantee does not cover damage, accidents or non-compliance with the instruction manual. Please contact rossmax service.

Product Information

Date of purchase:
Store where purchased:
Price Paid (excl. Tax):
Purchase for:

Questions about your Manual ? Post in the comments!

RossMax HA500 Thermometer Instruction Manual

RossMax HA500 Thermometer

INSTRUCTION MANUAL

Rossmax non-contact temple thermometer

Rossmax non-contact temple thermometer
Model: HA500
www.rossmax.com

Introduction

Rossmax non-contact temple thermometer using an infrared detector to detect body temperature from the temple for adult and child at home. This thermometer could also detect ambient temperature.
• The quality of the infrared temple thermometer has been verified and conforms to the provisions of the EC council directive 93/42/ EEC (Medical Device Directive) Annex I essential requirements and applied harmonized standards. Comply with ASTM E1965-98.
• This thermometer converts the temple temperature to display its “oral equivalent.”(according to the result of the clinical evaluation)

Please read the instruction manual carefully before using the product and be sure to keep this manual.

Introduction

LCD display

LCD display
  • The temple temperature measurement mode
  • The object temperature measurement mode
  • When battery icon shows, please replace the battery.

Function

Function

How to measure temple temperature

  1. Always make sure the probe is clean, and without damage.
  2. Press “ON/OFF/Memory” button to power on the device.
  3. Vertically aim the thermometer at the temple with a distance of less than 5 cm. If the temple is covered with hair, sweat or dirt, remove the obstacle from the temple to improve the measuring accuracy.
  4. Press the “Start” button to take temperature. Measurement is complete when you hear a long beep sound.
  5. Read the recorded temperature from the LCD display.
  6. Clean the probe after each use to ensure an accurate reading and avoid cross contamination. ( See the section of Care and Cleaning for details.)
  7. Remember to put in the storage case when not in use.
How to measure temple temperature

Switching between Fahrenheit and Celsius

  1. Make sure the device is off. (Or you can turn off the device by pressing and holding the “On/Off/Memory” button for 3 seconds.)
  2. Hold onto the “Start“ button, then press and hold the “On/Off/ Memory” button until °C appears on the LCD.
  3. Press the “On/Off/Memory” button to select the desired scale °C or °F, once you decide the scale, wait for 5 seconds and the setting will be confirmed while you will hear 2 short beep sounds.

How to measure object temperature

When you want to measure object temperature, you have to change to Object Mode.

  1. Make sure the device is turned off.
  2. Press and hold down the “Start” button. After about 3 seconds, the display will show this sequence:
How to measure object temperature

3. Release the “Start” button when the desired measurement mode is shown and 1 short beep sound will be heard.

4. When you are at Object Mode, press the “Start” button to get the real temperature.

Note:

  1. Applications include temperature measurements for Water, Milk, Cloth, Skin or other object.
  2. This mode shows the actual, unadjusted object temperatures, which is different from the body temperature.

Care and cleaning

Care and cleaning
  1. The probe is the most delicate part of the thermometer. Use with care when cleaning the lens to avoid damage.
  2. After the measurement, please use the cotton swab with the Alcohol (70% concentration) to clean the inside of the probe, including lens and metal parts.
  3. Allow the probe to fully dry for at least 5 minutes.
  4. Storage temperature range: It should be stored at room temperature between -25~+55°C, RH<=95%
  5. Keep the unit dry and away from any liquids and direct sunlight.
  6. The probe should not be submerged into liquids.
  7. Please check the device if damaged once it falls. If you can’t make sure of it, please send the complete device to the nearest retailer for re-calibration.
  8. Holding the thermometer too long may cause a higher ambient temperature reading of the probe. This could make the body temperature measurement lower than usual. Please try not to touch the thermometer probe part for avoiding the incorrect reading.

Battery Replacement

  1. Open the battery cover: use thumb to push battery cover out.
  2. Hold the device and flip the battery out.
  3. Insert the new battery down with the correct electrical polarity.
  4. Place back the battery cover.
  5. Keep the battery away from children.
Battery Replacement

Troubleshooting:

Troubleshooting:
Troubleshooting:

Specification

Specification

*Dispose of device and batteries according to local regulations

Caution

  1. Only use the device once you have read and understood these instructions for use. Keep the instruction manual for use.
  2. The thermometer and patient needs to stay in the room in which the measurement is taken for at least 30 minutes before use.
  3. It is recommend that you always take the temperature in the same location, since temperature readings may vary according to the locations.
  4. It is recommended that three temperatures are taken and the highest one taken as the reading if:
    a) New born infants
    b) Children with a compromised immune system and for whom the presence or absence of fever is critical.
    c) When the user is learning how to use the thermometer for the first time until he/she has familiarized himself/herself with the instrument and obtains consistent readings.
    d) The reading is extremely low.
  5. Do not take a measurement while drinking, eating, sweating or exercising.
  6. Do not take measurement while or immediately after nursing.
  7. Children is not allowed to use the device. Medical products are not toys.
  8. Influences on body temperature
    a) A person’s individual metabolism
    b) Age: Greater temperature fluctuations occur faster and more often in children. Normal body temperature decreases with age.
    c) Clothing
    d) Outside temperature
    e) Time of day: Body temperature is lower in the morning and increases throughout the day towards evening.
    f) Activities: Physical and, to a lesser extent, mental activities increase body temperature.
  9. This device is not shock-protected. Do not drop or expose to heavy shock this device.
  10. Do not bend the device.
  11. Do not disassemble or make modifications the device.
  12. Please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at your local retailer or at appropriate collection points provided in your country.
  13. Do not boil the probe.
  14. Do not use the device if it operates irregularly or any error massage showed.
  15. Do not use thinner or benzene to clean the device.
  16. Wipe the device clean before storing.
  17. When take the device from storage at below or above 15~40°C(59~104°F), place it in 15~40°C(59~104°F) temperature range for at least 30 minutes before use.
  18. Remove the battery if the device will not be used for a long time.
  19. If this device is used according to the operation instruction, periodic re-calibration is not required. If you still have questions, please send the complete device to dealers.
  20. Please note that this is a home healthcare product only, and it is not intended to serve as a substitute for the advice of a physician or medical professional.
  21. Do not use this device for diagnosis or treatment of any health problem on disease. Measurement results are for reference only. Contact your physician if you have or suspect any medical problems. Do not change your medications without the advice of your physician or healthcare professional.
  22. This device may not meet its performance specification if stored or used outside temperature and humidity ranges specified in specifications.
  23. Battery should not be charged or placed into extreme heat as it may explode.
  24. The thermometer contains small parts (ex: battery, etc.) that can be swallowed by children. Therefore never leave the thermometer unattended to children.
  25. Be sure to consult a doctor if you feel that your health is in poor condition.
  26. Do not judge your health only on the presence or absence of a fever.

EMC guidance and manufacturer’s declaration

EMC guidance
EMC guidance
Guidance and manufacturer’s
Guidance and manufacturer’s

Warranty

This instrument is covered by a 5 year guarantee from the date of purchase, batteries and accessories are not included. The guarantee is valid only on presentation of the guarantee card completed by the dealer confirming date of purchase or the receipt. Opening or altering the instrument invalidates the guarantee. The guarantee does not cover damage, accidents or non-compliance with the instruction manual. Please contact Rossmax service.

Date of purchase:
Store where purchased:
Price Paid (excl. Tax):
Purchase for:

Questions about your Manual ? Post in the comments!

RossMax RA600 Thermometer Instruction Manual

RossMax RA600 Thermometer

INSTRUCTION MANUAL

RossMax Digital Thermometer

RossMax Infrared Ear Thermometer
Model: RA600
www.rossmax.com

Please read the instruction manual carefully before using the product and be sure to keep this manual

RA600 Infrared Ear Thermometer

The Rossmax Infrared Ear thermometer has been carefully developed for accurate, safe and fast temperature measurements in the ear.

It is a non-invasive ear thermometer using an infrared detector to detect body temperature from the auditory canal for adult and child.

  • The quality of the infrared ear thermometer has been verified and conforms to the provisions of the EC council directive 93/42/EEC(Medical Device Directive) Annex I essential requirements and applied harmonized standards. EN 12470-5: 2003 Clinical thermometers-Part 5: Performance of infrared ear thermometers (with maximum device.)
  • This thermometer converts the ear temperature to display its “oral equivalent.” (according to the result of the clinical evaluation)
RA600 Infrared Ear Thermometer

LCD display

LCD display
  • It means measurable and reminds to use a probe cover for measurement.
  • When battery icon always appears, please replace the battery.

How to use the RA600 Infrared Ear Thermometer

  1. To achieve accurate readings, make sure a new, clean probe cover is in place before each measurement and the ear canal is clean.
    a. Install the probe cover by clockwise rotating then fix it.
    b. Remove the probe cover by anti-clockwise rotating then releasing it.
  2. Press the POWER BUTTON “On/Off/Memory” button, the thermometer is ready
    for use after the ear icon is flashing, two beeps are sounded, and three dash segments are appeared.
  3. Gently pull the ear back to straighten the ear canal and snugly position the probe into the ear canal, aiming towards the membrane of the eardrum to obtain an accurate reading.
    a. Before measurement, correct installation of the probe cover ensures accurate measurement.
How to use the RA600

b. Replace the probe cover after each use to ensure an accurate reading and avoid cross contamination.
c. This thermometer must only be used with rossmax probe covers, other covers can lead to inaccuracy. If running out of probe covers, please contact with the original seller or distributor for buying new probe covers.

4. Measuring the ear temperature: Use the index finger to trigger, by pressing “Start” button, a long beep will be sounded when measurement is done.

5. For the next measurement, remove the used probe cover and put on a new one.

6. Power off: If left idle for more than 1 minute, device will automatically shut off for extending battery life. Or press POWER BUTTON“On/Off/Memory” button for at least 3 seconds to turn the device off.

7. Fever alarm: When the measuring temperature is higher than 37.5 °C(93.2°F), the reading will flash, the backlight will be enabled, and 4 short beeps will be sounded. If measuring temperature is higher than 42.2 °C(108°F), the display will show “Hi”, the backlight will be enabled, and 4 short beeps will be sounded.
a. It is recommended that you measure 3 times with the same ear within a short period of time. If the 3 consecutive measurements are different, select the highest temperature.
b. To avoid the risk of cross contamination, please clean the probe according to “Clean and Storage“ section after each use.

Scanning Mode

If you continuously obtain different measurement results, it is recommended that you use Scanning Mode to measure.

Measuring the ear temperature: Use the index finger to trigger, press and hold the “Start” button for 3 seconds to take measurement. During the measuring process, gently pivoting the probe side-to-side to view the entire ear canal or in order to find the highest temperature. Release the “Start” button until hearing a long beep sound and the measurement is completed.

Enabling or disabling the beep sound

  1. Turn off the device.
  2. Hold down the “Start” button, then press and hold the“ON/OFF/ Memory” button until the LCD shows °C.
  3. Press the “ON/OFF/Memory” change beep sound from on to off, then release the “ON/OFF/Memory” button.
  4. After 6 seconds without changing, the beep On/Off setting will be completed, and the unit will be entered into the measurement mode.

Switching between temperature scale Fahrenheit and Celsius

To change the Unit from °C to °F:

Switching between temperature scale Fahrenheit and Celsius
  1. Turn off the device.
  2. Hold down the “Start” button, then press and hold the“ON/OFF/Memory” button until the LCD shows °C.
  3. Press the “Start” to change the °C to °F, then release the “Start” button.
  4. During the setting adjustment, each old or new temperature scale setting will be flashing for 6 seconds. After 6 seconds without changing, the temperature scale adjustment will be completed, and the unit will be entered into measurement mode.

Memory function

There are total 9 set memories for measurement records. If the reading of the thermometers is within the normal temperature range of 34 °C to 42.2 °C (93.2 °F to 108°F ), when the measurement is done, the measurement data is saved into memory.

  • Press POWER BUTTON“On/Off/Memory” button to repeatedly to recall each temperature memory.

Cleaning and storage

The probe is the most delicate part of the thermometer. Use with care when cleaning the lens to avoid damage.

Cleaning and storage
  1. Please use the cotton swab with the Alcohol to clean the lens (on the inside of the probe).
  2. Allow the probe to fully dry for at least 5 minutes.
    a. Please check the device if it falls and damages. If you can’t make sure of it, please send the complete device to the nearest retailer for recalibration.
    b. Keep the unit dry and away from any liquid and direct sunlight. The probe should not be submerging into liquids.

Change the battery

Change the battery
  1. This thermometer is equipped with one lithium cell (CR2032).
  2. Turn off the thermometer before replacing the battery.
  3. Open the battery cover: Hold the device and flip the battery out by sticking the pen tip into the battery storage well as illustrated.
  4. Insert a new battery and ensure the battery positive polarity is facing upward.
  5. Place back the battery cover.
  • The positive (+) side up and the negative (-) side pointed down.

Troubleshooting

Troubleshooting
Troubleshooting

Specification

Specification

*Dispose of device and batteries according to local regulations

Caution

  1. Besides the oral temperature, the body temperature measured by ear may be different from measurements taken by rectal or axillary. Therefore, there is no any meaning to compare them. Take the temperature periodically to find out the normal ear temperature reading , then use that reading as the basis for comparison with any measurement taken when you suspect a fever.
  2. This thermometer is designed for ear temperature measurement. Do not use this thermometer for other body site measurement.
  3. Keep the unit dry and away from where it might be exposed to moisture, liquids, direct sunlight, high temperature, high humidity, or excessive dust.
  4. This device is not shock-protected. Do not drop, heavily pressure the unit or fall from high place.
  5. Do not bend the device.
  6. Do not disassemble or make modifications on the device.
  7. Please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at your local retailer or at appropriate collection points provided in your country.
  8. Do not boil the probe.
  9. Do not use the device if it operates abnormally or error massage is showed.
  10. Do not use thinner or benzene to clean the device.
  11. Wipe the device clean before storing.
  12. When taking the device from storage below or above 10~ 40°C(50~104°F), place it in 10~ 40°C(50~104°F) temperature range for at least 30 minutes before use.
  13. Remove the battery if this device is not used for a period of time.
  14. If this device is used according to the operation instruction, periodic re-calibration is not required. If you still have questions, please send the complete device to dealers.
  15. Please note that this is a home healthcare product only, and it is not intended to serve as a substitute for the advice of a physician or medical professional.
  16. Do not use this device for diagnosis or treatment of any health problem on disease. Measurement results are for reference only. Contact your physician if you have or suspect any medical problems. Do not change your medications without the advice of your physician or healthcare professional.
  17. This device may not meet its performance specification if stored or used outside temperature and humidity ranges specified in specifications.
  18. Battery should neither be charged nor placed into the extreme environment, or it may explode.
  19. The thermometer contains small parts (ex: battery, etc.) that can be swallowed by children. Therefore never leave the thermometer unattended to children.
  20. After wearing the probe cover, the ear thermometer probe must be vertically and snugly inserted into the ear channel so as to get the correct temperature reading.
  21. Be sure to consult a doctor if you feel that your health is in poor condition.
  22. Do not judge your health only on the presence or absence of a fever.

EMC guidance and manufacturer’s declaration

EMC guidance and manufacturer’s declaration
EMC guidance and manufacturer’s declaration
EMC guidance and manufacturer’s declaration

Warranty

This instrument is covered by a 5 year guarantee from the date of purchase, batteries and accessories are not included. The guarantee is valid only on presentation of the guarantee card completed by the dealer confirming date of purchase or the receipt. Opening or altering the instrument invalidates the guarantee. The guarantee does not cover damage, accidents or non-compliance with the instruction manual. Please contact Rossmax Service.

Product Information

Date of purchase:
Store where purchased:
Price Paid (excl. Tax):
Purchase for:

Questions about your Manual ? Post in the comments!

RossMax TG100/TG120 Thermometer Manual

RossMax TG100

INSTRUCTION MANUAL

RossMax Digital Thermometer

RossMax Digital Thermometer
Model:TG100\TG120
www.rossmax.com

Introduction

The Digital Medical Thermometer provides quick, highly accurate reading over the human body temperature range. Please read the instructions completely first.
The quality of the thermometer has been verified and conforms to the provisions of the EC council directive 93/42/EEC(Medical Device Directive) Annex I essential requirements and applied harmonized standards. EN 12470-3: 2000 /A1: 2009 Clinical thermometers-Part 3: Performance of compact electrical thermometers (non-predictive and predictive) with maximum device.

Attention: Consult the accompanying documents. Please read this manual carefully before use. Please be sure to keep this manual.

Parts Identification

How to Use

1.Push the On/Off button by the display window. The display will
read

 beep sound will be heard

for 2 seconds and beep sound will be heard.

2. Releasing the on/off button, last measured temperature will be shown for about 2 seconds. Then shows the self-test temperature 37.0°C(98.6°F),and then Lo°C (Lo°F) displays.

3. Wipe or dip the probe with alcohol for disinfection. Position the probe in oral, rectal or axillary site.

4. Once the degree sign °C ( °F) on the display has stopped flashing (usually within 30 to 60 seconds), an Beep signal will sound for approx. 10 times, the measured temperature is shown on LCD window. The temperature reading will not change after the unit is removed from testing position. If the temperature <37.8°C(100.0°F ), the buzzer will alarm “Bi—Bi—Bi—Bi—”. If the temperature ≥ 37.8°C (100.0°F), the buzzer whose frequency is higher will alarm “Bi-Bi-Bi—-Bi-Bi-Bi–” about 10 times rather than”Bi—Bi—Bi—Bi—”

5. The unit will automatically turn off in 10 minutes for energy saving. However, to prolong the life of the battery, it is suggested to press the On/Off button to turn the unit off once the measurement is done.

6. Please dispose of any used battery and the thermometer according to the local regulations.

Note: After step 2, if the room temperature is greater than 32.0°C (89.6°F ). it will be displayed the room temperature. Note: Usage of the probe cover may result in a 0.1°C(0.2°F) difference from actual temperature.

Note: To clean the probe before and after using the thermometer to ensure an accurate reading and avoid cross contamination approximately.

Oral Use

Place the probe well under the patient’s tongue. Confirm the patient to keep his mouth closing for about 1 minute.

Do not drink hot or cold fluids, exercise, and smoke or perform other activities prior to a reading. These activities will raise or lower temperature readings when compared to your normal, average temperature.

Axillary Use

Tightly place probe in the patient’s armpit for about 1~5 minutes. *Please ensure the close contact between the probe and the armpit of the baby or children.

Rectal Use

Always uses probe cover when taking rectal measurements.

  1. Commonly used for young children when it is difficult to take an oral or axillary temperature.
  2. Lubricate with a water-soluble gel. Do not use petroleum jelly.
  3. Gently insert the probe tip no more than 1.5-2 cm into the rectum
    for about 1 minute. Do not force the tip into the rectum if resistance is encountered.
  4. Disinfect the thermometer after use. Refer to “cleaning and disinfection“section.

ºC /ºF Switchable

Temperature readings are available in the Fahrenheit or Celsius scale (°C / °F; located in the right of LCD.) With the unit off, press and hold the On/Off Button for approximately 4 seconds to change the current setting.

Battery Replacement

  1. When the BATTERY SIGN appears on the upper right corner of the LCD, the battery is exhausted and needs replacement.
  2. Pull the battery cover off in the direction shown below.
  3. Pull out the battery with a sharp objects such as pen. Keep exhausted battery from reaching by the children.
  4. Place a new 1.5V D.C. button size battery type SR41 or LR41 or equivalent in the chamber with positive side faced up and negative side faced down.
  5. Install the battery cover back.

Display on the LCD

M: Last measured temperature

Display on the LCD

When the BATTERY SIGN appears on the upper right corner of the LCD, the battery is exhausted and needs replacement.

Troubleshooting

Troubleshooting

Cleaning and Disinfection

  1. Clean the unit by wiping it with a dry cloth and sterilize the probe with ethyl alcohol.
  2. Don’t let the unit contact any chemical thinner.
  3. Not waterproof. Do not soak the display in water. Only the probe is waterproof.

Caution

  • Do not bend or drop the thermometer. It is not shockproof.
  • Do not boil probe for disinfect.
  • Do not store the unit under direct sunlight, at a high temperature, in high humidity or dust. Neither store the unit under the sunlight, nor at the high temperature or humidity.
  • Do not disassemble. See BATTERY REPLACEMENT to replace battery.
  • Avoid strong electromagnetic interference such as microwave ovens and cell phones.
  • Please be noticed to keep the probe dry before putting the thermometer into the carry case.
  • The thermometer contains small parts (battery, etc.) that can be swallowed by children. Therefore never leave the thermometer unattended to children.
  • The thermometer should be cleaned after measurement no matter the probe cover has been installed or not.
  • Battery should not be charged or placed into extreme heat as it may explode.
  • Do not use the thermometer in ear. Intended use is for oral, axillary and rectal measurement.
  • Use of the probe cover may result in a 0.1ºC(0.2ºF) discrepancy from actual temperature.
  • Remove battery from the thermometer when not in operation for a long time.
  • If the unit is stored in an extreme environment before measurement, please make sure it has been firstly adapted in the room temperature, so that the unit can be measured normally.
  • Please note that this is a home healthcare product only, and it is not intended to serve as a substitute for the advice of a physician or medical professional.
  • Do not use this device for diagnosis or treatment of any health problem on disease. Measurement results are for reference only. Contact your physician if you have or suspect any medical problems. Do not change your medications without the advice of your physician or healthcare professional.
  • This device may not meet its performance specification if stored or used outside temperature and humidity ranges specified in specifications.
  • If this device is used according to the operations instruction, periodic re-calibration is not required. If you still have questions, please send the device to dealers.
  • Please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at your local retailer or at appropriate collection points provided in your country.
  • This device is for oral, axillary and rectal use only.
  • High, prolonged fever requires medical attention especially for young children. Please contact your physician.
  • For save reason, during children’s temperature measurement, please keep them from crying, walking, talking and any related dangerous activities.

Specifications

EMC guidance and manufacturer’s declaration

EMC guidance and manufacturer’s declaration
EMC guidance and manufacturer’s declaration
Guidance and manufacturer
Guidance and manufacturer’s
Guidance and manufacturer’s
Recommended separation

Warranty

This instrument is covered by a 5 year guarantee from the date of purchase, batteries and accessories are not included. The guarantee is valid only on presentation of the guarantee card completed by the dealer confirming date of purchase or the receipt. Opening or altering the instrument invalidates the guarantee. The guarantee does not cover damage, accidents or non-compliance with the instruction manual. Please contact rossmax service.
Product Information
Date of purchase:
Store where purchased:
Price Paid (excl. Tax):
Purchase for:

Questions about your Manual ? Post in the comments!