Rough Country Hard Tri-Fold Tonneau Cover Instruction Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Rough Country Hard Tri-Fold Tonneau Cover. Designed for durability and security, this low-profile aluminum truck bed cover enhances your vehicle's functionality and appearance.

Safety Information

Important: Rough Country recommends installation by a certified technician. Knowledge of Rough Country instructions, suspension procedures, and post-installation checks are required. Improper installation may impact the integrity and operating safety of the product. It is the buyer's responsibility to check all bolts/nuts for tightness after the first 500 miles, and then every 1,000 miles. Wheel alignment, steering system, suspension, and driveline systems must be inspected by a qualified, professional mechanic at least every 3,000 miles.

What's in the Box

• (1) Flush Bed Cover
• (1) Bulkhead Seal
• (2) Mounting Rails
• Hardware
• Drainage Tubes

Setup & Installation

The Rough Country Hard Tri-Fold Tonneau Cover is designed for a simple, hassle-free, no-drill installation. All necessary tools are included.

1. Prepare the Bed: Ensure your truck bed is clean and free of debris.
2. Install Bulkhead Seal: Apply the provided bulkhead seal along the front of the truck bed, near the cab, to ensure a weather-tight seal.
3. Attach Mounting Rails: Secure the two mounting rails to the bedsides. These rails are designed to clamp into place without drilling.
4. Install Drainage Tubes: Connect the drainage tubes to the rails to channel water away from the truck bed.
5. Position the Cover: Carefully place the tri-fold cover onto the installed rails.
6. Secure the Cover: Utilize the auto-latching system and clamps to firmly secure the cover to the rails.

For a detailed visual guide, please refer to the official installation video below or download the Installation Manual (PDF).

Image showing the Rough Country Hard Low Profile Bed Cover partially folded, highlighting its tri-fold design for quick cargo access.

Close-up image illustrating the single cable pull mechanism for easy latch release on the Rough Country Hard Low Profile Bed Cover.

Operating the Tonneau Cover

The tri-fold design allows for versatile access to your truck bed.

• Opening: To open the cover, simply pull the release cable located underneath the rear panel. This will disengage the latches. You can then fold the panel forward.
• Partial Access: Fold one or two panels forward to access specific areas of your truck bed. Nylon straps are provided to secure the cover in the 2/3 open position, allowing you to drive with it partially open.
• Full Access: To gain full access to your truck bed, fold all panels towards the cab. The cover can be secured upright against the cab using the integrated straps and buckles.
• Closing: To close, simply unfold the panels back towards the tailgate. The auto-latching system will secure the panels upon closure.

Image showing the nylon straps and latches used to secure the Rough Country Hard Low Profile Bed Cover in a partially open position, allowing for driving.

Maintenance

To ensure the longevity and optimal performance of your tonneau cover, regular maintenance is recommended:

• Cleaning: Clean the aluminum panels with mild soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the matte black finish.
• Seals: Periodically inspect all rubber seals for wear and tear. Ensure they are free of debris to maintain a watertight seal.
• Hardware: Regularly check all clamps, latches, and mounting hardware for tightness. Tighten as necessary to prevent movement and ensure security.
• Drainage Tubes: Ensure drainage tubes are clear of obstructions to allow proper water runoff.

Troubleshooting

If you encounter any issues with your tonneau cover, consider the following:

• Water Leaks:
  • Check the bulkhead seal at the front of the bed for proper adhesion and placement.
  • Ensure all panels are fully latched and the tailgate is securely closed.
  • Verify that drainage tubes are not clogged and are properly channeling water away.
  • Inspect rubber seals along the edges of the panels for any damage or misalignment.
• Latching Issues:
  • Ensure the mounting rails are securely clamped and properly aligned.
  • Check the release cables for any kinks or obstructions that might prevent smooth operation.
  • Verify that the auto-latching mechanism is free of debris and operating correctly.
• Panel Alignment:
  • Confirm that the cover is centered and square on the truck bed. Adjust the mounting rails if necessary.

Specifications

Warranty & Support

Rough Country backs this tonneau cover with a 5-Year Warranty, ensuring its readiness for any adventure.

For further assistance or inquiries, please contact Rough Country Customer Support. You can also refer to the Installation Manual (PDF) for detailed information.