Introduction
This manual provides comprehensive instructions for the assembly, operation, and maintenance of your Yaheetech Adjustable Drafting Table, Model YA-00120594. Please read this manual carefully before use to ensure proper setup and safe operation. Keep this manual for future reference.
Important Safety Information
WARNING: Do not overload the product. Ensure all components are securely fastened before use. Always follow assembly instructions carefully. Keep small parts away from children.
For your safety, please adhere to the maximum load capacity of 100 kg for the table.
Components List
Please verify that all parts are present before beginning assembly. If any parts are missing or damaged, please contact Yaheetech customer support.
- Main Tabletop (Adjustable)
- Side Extension Table (Pull-out)
- Table Frame (Legs and Supports)
- Stool (Seat and Legs)
- Fabric Drawers (2 units)
- Pencil Ledge/Stopper
- Side Tray with Compartments
- Perforated Storage Shelf (Underneath)
- Assembly Hardware (Screws, bolts, tools - not explicitly listed but implied)
Image: Overview of the Yaheetech Adjustable Drafting Table and accompanying stool, showing its main components.
Setup and Assembly
Assembly typically requires two adults. Please follow these steps carefully.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
- Assemble Table Frame: Attach the table legs and support beams using the provided hardware. Ensure all connections are secure.
- Attach Main Tabletop: Secure the main tabletop to the assembled frame. Pay attention to the tilting mechanism.
- Install Side Extension: Slide the side extension table into its designated slot.
- Insert Drawers and Accessories: Place the fabric drawers into their compartments. Attach the pencil ledge and side tray.
- Assemble Stool: Connect the stool seat to its legs using the provided hardware.
- Final Check: Verify that all screws and bolts are tightened and the table is stable before use.
Image: An illustrative diagram showing the various parts of the drafting table and their assembly points.
Operating Instructions
Adjusting Table Height
The table height can be adjusted from 69.5 cm to 92.5 cm. Locate the adjustment knobs on the table legs. Loosen the knobs, adjust the table to your desired height, and then securely tighten the knobs to lock the position.
Tilting the Tabletop
The main tabletop can be tilted from 0 to 60 degrees. To adjust the angle, release the locking mechanism (usually a lever or knob) located beneath the tabletop. Adjust to the desired angle and re-engage the lock.
Image: Close-up view of the tabletop tilting mechanism, showing how to adjust the angle.
Using the Side Extension Table
The 60 x 38 cm side surface can be pulled out to provide additional workspace for laptops, tablets, or reference materials. When not in use, it can be slid back under the main tabletop.
Image: The side extension table fully extended, demonstrating its use as an additional surface.
Utilizing Storage Features
The table includes a detachable side tray with separate slots for stationery, two fabric drawers for organized storage, and an open shelf underneath for larger items like paper rolls or paint jars. The metal pencil ledge can be locked or loosened to prevent items from sliding off the tilted surface.
Image: Detail of the integrated storage features, including the side tray with compartments and the pencil ledge.
Maintenance
Cleaning
Wipe the table surfaces with a dry cloth. For stubborn marks, use a slightly damp cloth with mild soap, then dry immediately. Avoid abrasive cleaners or harsh chemicals that may damage the finish.
Care
Regularly check all screws and bolts to ensure they remain tight. Avoid placing excessively hot or cold items directly on the surface. Do not expose the table to prolonged direct sunlight or extreme humidity.
Troubleshooting
Table is Unstable
- Ensure all assembly hardware is securely tightened.
- Check that the table is placed on a flat, level surface.
- Verify that the height adjustment knobs are fully tightened after adjustment.
Tabletop Does Not Tilt Smoothly
- Inspect the tilting mechanism for any obstructions.
- Ensure the locking lever/knob is fully disengaged before attempting to tilt.
Drawers Do Not Slide Easily
- Check for any items obstructing the drawer path.
- Ensure the fabric drawers are correctly inserted into their compartments.
Specifications
| Feature | Detail |
|---|---|
| Model | YA-00120594 |
| Materials | Powder-coated Metal Frame, MDF with waterproof and scratch-resistant veneer |
| Overall Dimensions (L x W x H) | 120.5 x 60 x (69.5-92.5) cm |
| Main Tabletop Dimensions | 98.5 x 60 cm |
| Side Extension Table Dimensions | 60 x 38 cm |
| Adjustable Height Range | 69.5 cm to 92.5 cm |
| Tabletop Tilt Angle | 0 to 60 degrees |
| Stool Dimensions | 30 cm (Diameter) x 52 cm (Height) |
| Maximum Load Capacity (Table) | 100 kg |
| Product Weight | 23.5 kg |
| Color | Black |
Image: Detailed diagram showing the dimensions of the drafting table and stool.
Warranty and Support
Yaheetech products are designed for quality and durability. For warranty information, product support, or to purchase replacement parts, please visit the official Yaheetech website or contact our customer service department. Please have your model number (YA-00120594) and purchase date available when contacting support.
You can find more information and contact details on the Yaheetech Brand Store.
