1. Product Overview
This manual provides comprehensive instructions for the installation, operation, and maintenance of your AIKE Automatic Soap Dispenser (Model AK1206). Designed for commercial and high-traffic environments, this wall-mounted liquid dispenser offers hygienic, touch-free operation with a large 1100ml capacity and adjustable soap supply.
2. Setup and Installation
The AIKE AK1206 dispenser is designed for surface mounting with screws. Proper installation is crucial for optimal performance and hygiene.
2.1 Installation Steps
- Mark Mounting Holes: Use the provided mounting plate as a template to mark the drilling points on the wall.
- Drill Holes: Drill holes at the marked positions.
- Insert Anchors: Insert wall anchors (if necessary for your wall type) into the drilled holes.
- Secure Mounting Plate: Attach the mounting plate to the wall using the screws.
- Mount Dispenser: Carefully align the dispenser with the mounting plate and slide it down until it locks securely into place.
- Install Batteries: Open the battery compartment (usually at the bottom or back) and insert 4 AA batteries (not included), ensuring correct polarity.
2.2 Recommended Installation Distance
To ensure proper sensor function and prevent accidental dispensing, maintain the following minimum distances from the unit to the desktop or counter surface:
- Normal Countertop: At least 9.84 inches (25 cm)
- Reflective Countertop (e.g., polished stone, metal): At least 13.8 inches (35 cm)
2.3 Installation Video Guide
For a visual guide on installation, please refer to the official video below:
3. Operating Instructions
Operating your AIKE Automatic Soap Dispenser is simple and hygienic.
3.1 Refilling the Dispenser
The dispenser has a large 1100ml capacity, supporting over 500 dispenses before needing a refill. It is compatible with most liquid soaps, gels, and hand sanitizers. Ensure the liquid soap does not contain particles that could clog the mechanism.
- Unlock Top Cover: Use the provided key or press the release button to open the top cover of the dispenser.
- Pour Liquid: Carefully pour liquid soap into the reservoir. Avoid overfilling.
- Close Cover: Close the top cover securely until it clicks into place.
3.2 Turning On/Off and Adjusting Soap Supply
The dispenser features five adjustable levels for soap supply, ranging from 0.5ml to 2.5ml per dispense.
- Turn On: Locate the power button (often at the bottom or side). Press and hold the button until the indicator light flashes 3 times, indicating it's on.
- Adjust Supply Level: After turning on, briefly press the power button repeatedly to cycle through the five soap supply levels. The indicator light will flash a corresponding number of times (1 to 5) to show the current level.
- Dispense Soap: Place your hand under the sensor. The dispenser will automatically dispense the set amount of soap.
- Turn Off: Press and hold the power button until the indicator light turns off.
4. Maintenance
Regular maintenance ensures the longevity and hygienic operation of your dispenser.
- Cleaning: Wipe the exterior of the dispenser with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the stainless steel finish.
- Sensor Cleaning: Keep the sensor area clear of soap residue or debris to ensure accurate detection.
- Soap Type: Use liquid soap without solid particles to prevent clogging of the pump mechanism. If using thick soap, dilute it with a small amount of water if necessary, ensuring it remains effective.
- Battery Replacement: Replace batteries when the indicator light flashes rapidly or the dispenser stops responding. Always replace all batteries at once with new ones of the same type.
5. Troubleshooting
If you encounter issues with your AIKE Automatic Soap Dispenser, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Dispenser not dispensing soap. | Low battery, empty reservoir, clogged pump, sensor obstruction. | Check/replace batteries. Refill soap. Check for clogs in the nozzle. Clean sensor area. |
| Weak or inconsistent soap dispense. | Low battery, soap too thick, air in pump. | Replace batteries. Dilute soap slightly. Prime the pump by repeatedly activating the sensor until soap flows consistently. |
| Indicator light not working. | Dead batteries, internal fault. | Replace batteries. If issue persists, contact customer support. |
| Accidental dispensing. | Dispenser too close to reflective surface or object. | Ensure proper installation distance from countertop (refer to Section 2.2). Remove any objects near the sensor. |
6. Product Specifications
Detailed specifications for the AIKE AK1206 Automatic Soap Dispenser:
- Model Number: AK1206
- Color: Brushed Stainless Steel
- Material: Stainless Steel
- Product Dimensions (L x W x H): 5.12" x 3.15" x 10.24"
- Shape: Rectangular
- Unit Count: 1.0 Count
- Liquid Volume Capacity: 1100 Milliliters
- Item Weight: 2.42 pounds
- Manufacturer: Zhejiang AIKE Appliances Co., Ltd.
- Date First Available: September 14, 2020
7. Warranty and Support
For specific warranty information and customer support, please refer to the documentation included with your product packaging or visit the official AIKE website. Keep your purchase receipt for warranty claims.
