1. Introduction
This manual provides essential information for the safe installation, operation, and maintenance of your Eglo 20998M Pistoia 3-Light Pendant Luminaire. Please read these instructions carefully before beginning installation and retain them for future reference. This luminaire is designed for indoor use only.
2. Safety Information
- Always disconnect power at the main circuit breaker before installation, maintenance, or bulb replacement.
- Installation must be performed by a qualified electrician in accordance with all local electrical codes.
- Ensure the mounting surface can support the weight of the luminaire.
- Do not exceed the maximum wattage specified for the bulbs (3x40W G9).
- Avoid touching bulbs with bare hands during replacement; use a clean cloth or glove.
- Keep packaging materials out of reach of children.
- Do not modify the luminaire in any way.
3. Package Contents
Verify that all components are present before beginning installation:
- Pendant Luminaire Base
- 3 Opal Glass Shades
- 3 G9 Bulbs (40W each)
- Mounting Hardware (screws, anchors, wire connectors)
- Instruction Manual
4. Setup and Installation
Assembly is required for this luminaire. Follow these general steps for installation. Specific details may vary; consult a qualified electrician if unsure.
4.1 Tools Required (Not Included)
- Screwdriver (Phillips and/or Flathead)
- Wire Strippers
- Pliers
- Electrical Tape
- Drill (if new mounting holes are needed)
- Ladder
4.2 Installation Steps
- Turn Off Power: Locate the circuit breaker controlling the light fixture and turn off the power. Verify power is off using a voltage tester.
- Prepare Mounting: Attach the mounting bracket to the junction box in the ceiling using the provided screws. Ensure it is securely fastened.
- Adjust Height: The pendant cables can be adjusted to your desired hanging height. Carefully feed the cables through the canopy and secure them.
- Wire Connections: Connect the luminaire's wires to the household electrical wires. Typically, connect black to black (live), white to white (neutral), and green/bare copper to green/bare copper (ground). Use wire connectors and secure with electrical tape.
- Secure Canopy: Carefully push the luminaire canopy up to the ceiling, covering the junction box and wiring. Secure it with the provided screws or nuts.
- Install Shades: Attach the opal glass shades to the lamp holders. Gently twist or secure them according to the design.
- Insert Bulbs: Carefully insert the G9 bulbs into the sockets. Do not overtighten.
- Restore Power: Once installation is complete and all connections are secure, restore power at the circuit breaker.
Figure 1: Front view of the Eglo 20998M Pistoia 3-Light Pendant Luminaire with three opal glass shades and satin nickel finish.
Figure 2: Close-up view showing the satin nickel finish of the luminaire's curved arm and one of the opal glass shades.
Figure 3: Detailed view of the connection point between the metal fixture and the opal glass shade, highlighting the G9 bulb socket area.
5. Operating Instructions
Once installed and power is restored, the Eglo 20998M Pistoia Luminaire operates like any standard light fixture. It is controlled by the wall switch connected to its electrical circuit.
- Turning On/Off: Use the wall switch to turn the luminaire on or off.
- Bulb Replacement: To replace a G9 bulb, ensure power is off at the circuit breaker. Allow the bulb to cool completely. Gently pull the old G9 bulb straight out from its socket. Insert the new G9 bulb by pushing it straight into the socket until it is firmly seated. Do not twist.
6. Maintenance
Regular cleaning will help maintain the appearance and performance of your luminaire.
- Cleaning: Ensure power is off and the luminaire is cool before cleaning. Wipe the metal parts with a soft, dry cloth. For the glass shades, use a soft, damp cloth with a mild, non-abrasive cleaner if necessary, then dry thoroughly.
- Do not use harsh chemicals, abrasive cleaners, or scouring pads, as these can damage the finish.
7. Troubleshooting
If your luminaire is not functioning correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power to the fixture Faulty bulb Loose wiring connection | Check circuit breaker and wall switch. Replace bulb(s). Turn off power and check wire connections. |
| Light flickers | Loose bulb Incorrect bulb type/wattage Loose wiring connection | Ensure bulbs are fully seated. Verify bulbs are G9 40W max. Turn off power and check wire connections. |
If these steps do not resolve the issue, consult a qualified electrician.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | 20998M |
| Brand | EGLO |
| Product Dimensions | 84 x 11 x 110 cm (Length x Width x Height) |
| Item Weight | 3.14 kg |
| Material | Alloy Steel (Fixture), Opal Glass (Shades) |
| Finish | Satin Nickel |
| Number of Lights | 3 |
| Bulb Type | G9 |
| Max Wattage per Bulb | 40W |
| Power Source | Corded Electric |
| Assembly Required | Yes |
| Included Components | Base, Shades, Sockets, Bulbs |
| Style | Modern |
| Room Type | Entryway (suitable for various indoor spaces) |
9. Warranty and Support
Warranty information for Eglo products is typically provided at the point of purchase or can be obtained directly from the manufacturer's official website. Please retain your proof of purchase for any warranty claims.
For technical support or further assistance, please refer to the contact information provided by your retailer or visit the official EGLO website.
