Document

Anker-LOGO

Anker SoundCore

Anker-SoundCore-PRODUCT

Anker SoundCore

For FAQs and more information, please visit
For FAQs and more information, please visit

Social Media

What’s Included

What’s Included

At a Glance

At a Glance

English

Using Your SoundCore

1. Turn on / off
Turn on

Note: SoundCore will automatically turn off after 10 minutes if no device is connected.

2. Charge your SoundCore

Charge your SoundCore

  • Flashing red Flashing red Low power
  • Steady red Steady red Charging
  • Off Off Fully charged

Use the included USB cable to charge your SoundCore and make sure it is fully charged before first use.

Pair with your device

Pair with your device

Un-pair connected device and re-enter pairing mode

Un-pair connected device and re-enter pairing mode

  • Rapidly flashing blue Rapidly flashing blue Pairing mode
  • Steady blue Steady blue Connected to a device

When turned on, SoundCore will automatically connect to the last connected device if available. If not, SoundCore will enter pairing mode. Having connection problems? Remove SoundCore from your device’s Bluetooth history, ensure it’s less than 3 feet away then try pairing again.

Connect via AUX

Connect via AUX

  • SoundLine AUX cable sold separately.
  • Rapidly flashing blue Rapidly flashing blue AUX mode

When using AUX mode, control audio playback via the connected device.

Controls

Play - pause Play – pause

 

Skip forwardSkip forward

 

Volume up - downVolume up / down

 

Answer - End callAnswer / End call

 

Reject call Reject call

 

  • Put current call on hold and answer incoming call Put current call on hold and answer incoming call

 

Switch between held call and active call

Specifications

  • Input : 5 V = 1 A
  • Audio output : 3 W × 2
  • Charging time : 5 – 6 hours
  • Play time (varies by volume level and content) : 24 hours
  • Size : 165 × 45 × 54 mm 6.5 × 1.8 × 2.1 in
  • Weight : 365 g / 12.9 oz
  • Range : 20 m / 66 ft

Attention

  • Use original or certified cables Use original or certified cables
  • Don’t expose to liquids Don’t expose to liquids
  • Don’t disassemble Don’t disassemble
  • Avoid dropping Avoid dropping
  • Avoid extreme temperatures Avoid extreme temperatures

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.

RF Warning Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Trademark

Trademark
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Anker Technology Co., Limited is under license.

Notice This product complies with the radio interference requirements of the European Community.

Declaration of Conformity

Hereby, Anker Technology Co., Limited declares that the radio equipment type A3102 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

www.anker.com
www.ankeroficial.com.br
[email protected]

  • BT Maximum output power: 1.5dBm
  • BT Frequency band: 2.4G band (2.4000GHz-2.4835GHz)

IC NOTICE TO CANADIAN USERS

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003.

warranty

  • 18-month limited warranty

Customer Service

  • Lifetime technical support
  • [email protected]
  • TEL: 1-800-988-7973
  • 00477-18-10554
  • Mon-Fri 9:00-5:00 PST (US)

Thanks

Questions about Anker SoundCore ? Post in the comments!

DOWNLOAD RESOURCES

FAQ’S

I can’t pair with SoundCore. How do I fix this?

Ensure Bluetooth is enabled on your device, then try pairing again.
Ensure you are within 3 feet of SoundCore. If the problem persists, remove SoundCore from your device’s Bluetooth history and try again.

I can’t connect to SoundCore via AUX. How do I fix this?

Make sure you are using the included SoundLine AUX cable, and that it is fully inserted into both ends. If the problem persists, remove SoundCore from your device’s Bluetooth history and try again.

Why does my music cut out when using AUX mode?

This may be due to a weak connection between your phone or tablet and the AUX cable. Try moving the cable around to find a better connection point, or use a different AUX cable if available. If you continue to experience problems, please contact our support team at www.anker.com/support .

Why does my music cut out when using Bluetooth mode?

This may be due to a weak connection between your phone or tablet and SoundCore. Try moving your phone or tablet closer to SoundCore until you find a good connection point, then try playing music again. If you continue to experience problems, please contact our support team at www.anker.com/support .

Is the Anker a3102 waterproof?

Anker doesn’t provide a weatherization rating, so I wouldn’t leave this speaker exposed to the elements or use it too close to the edge of a pool.

How loud are Anker speakers?

It’s loud enough to fill a small room, but will struggle to be heard on a noisy beach or street. This is to be expected from such a compact speaker with stellar battery life but it’s a trade-off nonetheless. Those who want 360-degree audio, waterproofing, and better sound should look at the UE Wonder boom. 

How many watts is Anker Soundcore?

Featuring a customized 3′ Runtrack Speaker driver with BassUp™ technology, it delivers a wide range of high-quality audio frequency at 10 watts. The Icon connects to devices via Bluetooth 5.0 and provides 12 hours of playtime on a single charge.

Does Anker SoundCore work with iPhone?

Compatibility: Bluetooth; works with all Mac’s, iPad’s, iPhone’s and iPods that have Bluetooth. This means in practice all Mac’s, iPads and iPhones and all iPod touches.

Does Anker speaker have mic?

Anker SoundCore 2 Portable Bluetooth Speaker with Better Bass, 24-Hour Playtime, 66ft Bluetooth Range, IPX5 Water Resistance & Built-in Mic, Dual-Driver Wireless Speaker (Red)

Does Anker Soundcore have app?

The Soundcore app is available on iOS and Android devices.

How do I know if my Soundcore is charging?

The SoundCore will take about 3 hours to charge with a 2 amp charger (like a tablet charger or Anker wall charger) or about 6-8 hours with a phone charger or laptop USB port. When the LED turns white it will have finished charging.

Why is my Anker Soundcore blinking red?

Your Bluetooth device may be out of range for connection. To solve this remove any obstacles between the speaker and your device, move as close as possible, and try to connect.

VIDEO

Anker-LOGO

Anker SoundCore
www://anker.com/

Join the Conversation

6 Comments

  1. I am trying to connect this device to my Playstation 3, but it asks for a passkey. There is no passkey i am aware of and I had this for a long time so I do not have the original box. Not even the online manual had a passkey for Playstation devices.

  2. I recently purchased an Anker Sound Core 2 with the built-in mic. I hope to use the speaker as a sound output only. We use the speaker for Skype and the other end only hears themselves due to the feedback from the mic being right next to the sound speaker. Is there a way to turn off the build-in mic?

  3. Is the aux connector truly stereo? I have tried four or five different cables which I *KNOW* are three-conductor (TRS) cables, yet the audio that comes through is always monaural, both channel playing through both speakers.

  4. I have two soundcare A3102 speakers, and I have tried to connect them together, but it was impossible. Is there any configuration to be able to do it? Or only the Soundcare 2 can be connected to each other?
    Tengo dos parlantes soundcare A3102, y he tratado de conectarlos entre sí, pero me ha sido imposible. Existe alguna configuración para poder hacerlo? O solo los Soundcare 2 se pueden conectar ente sí?

Leave a comment

Your email address will not be published.